LED双色单元板+STC12C5A60S2+DS1302制作电子钟 -

#include"STC12C5A60S2.h" /*头文件的包含*/
#include"zimo.h"
#include <intrins.h>
#include <ADC.H>
#include"led_595.h"
#include"DS1302.h"
sbit K1=P3^0;
sbit K2=P3^1;
sbit K3=P3^2;
sbit K4=P3^3;
unsigned char SetState,SetPlace=0;
void Int0Configuration();
unsigned char code temp_table[]={67, 70, 72, 74, 76, 78, 81, 83, 85, 87,
89, 90, 91, 93, 95, 97, 100,103,106,110,
113,116,119,122,125,128,131,133,136,139,
141,143,146,148,150,152,154,157,159,161,
163,165,167,169,171,173,175,176,178,180,
182,184,186,187,189,191,193,194,196,198,
199,200,201,202};
unsigned int temp_change(unsigned char temp1)
{
unsigned int i;
for(i=0;i<=63;i++)
{
if(temp_table[i]>temp1) break;
}
if(temp_table[i]==0) return 0;
else if(temp_table[i]==63) return 640;
else
{
return (unsigned int)((temp1-temp_table[i-1])*10/(temp_table[i]-temp_table[i-1])+(i-1)*10+5);
}
}
void SendTime(void)
{
unsigned int TempData;
GetTime();
TempData=GetADCResult(2);
TempData=temp_change(TempData);
line1_num[2]=TableDs1302[6]/10;
line1_num[3]=TableDs1302[6]%10;
line1_num[5]=TempData/100;
line1_num[6]=TempData%100/10;
line2_num[0]=TableDs1302[4]/10;
line2_num[1]=TableDs1302[4]%10;
line2_num[3]=TableDs1302[3]/10;
line2_num[4]=TableDs1302[3]%10;
line2_num[7]=TableDs1302[5]+10;
line3_num[0]=TableDs1302[2]/10;
line3_num[1]=TableDs1302[2]%10;
line3_num[3]=TableDs1302[1]/10;
line3_num[4]=TableDs1302[1]%10;
line3_num[6]=TableDs1302[0]/10;
line3_num[7]=TableDs1302[0]%10;
}
void main()
{
unsigned int i;
LED_Init();
DelayMS(100);
InitADC();
DelayMS(1000);
Int0Configuration();
if(K2==0)
{
DelayMS(1000);
InitDS1302();
}
while(1)
{
if(SetState==0)
{
SendTime();
for(i=0;i<10;i++) LED_Display();
}
else
{
SendTime();
for(i=0;i<20;i++) LED_Display();
for(i=0;i<2;i++)
{
if(SetPlace==0) {line3_num[6]=11;line3_num[7]=11;}
if(SetPlace==1) {line3_num[3]=11;line3_num[4]=11;}
if(SetPlace==2) {line3_num[0]=11;line3_num[1]=11;}
if(SetPlace==3) {line2_num[3]=10;line2_num[4]=10;}
if(SetPlace==4) {line2_num[0]=10;line2_num[1]=10;}
if(SetPlace==5) {line2_num[7]=10;}
if(SetPlace==6) {line1_num[2]=10;line1_num[3]=10;}
LED_Display();
}
if(K1==0) //检测按键K1是否按下
{
LED_Display(); //消除抖动
if(K1==0)
{
SetPlace++;
if(SetPlace>=7)
SetPlace=0;
}
while((i<50)&&(K1==0)) //检测按键是否松开
{
LED_Display();
i++;
}
i=0;
}
if(K2==0) //检测按键K2是否按下
{
LED_Display(); //消除抖动
if(K2==0)
{
TableDs1302[SetPlace]++;
if((TableDs1302[SetPlace]>=60)&&(SetPlace<2)) //分秒只能到59
{
TableDs1302[SetPlace]=0;
}
if((TableDs1302[SetPlace]>=24)&&(SetPlace==2)) //小时只能到23
{
TableDs1302[SetPlace]=0;
}
if((TableDs1302[SetPlace]>=32)&&(SetPlace==3)) //日只能到31
{
TableDs1302[SetPlace]=1;
}
if((TableDs1302[SetPlace]>=13)&&(SetPlace==4)) //月只能到12
{
TableDs1302[SetPlace]=1;
}
if((TableDs1302[SetPlace]>=8)&&(SetPlace==5)) //周只能到7
{
TableDs1302[SetPlace]=1;
}
if((TableDs1302[SetPlace]>=31)&&(SetPlace==6)) //年暂时到2030
{
TableDs1302[SetPlace]=0;
}
InitDS1302();
}
while((i<50)&&(K2==0)) //检测按键是否松开
{
LED_Display();
i++;
}
i=0;
}
}
}
}
void Int0Configuration()
……………………
…………限于本文篇幅余下代码请从51黑下载附件…………

复制代码