STM8控制HDMID三进一出的程序 -

标题: STM8控制HDMID三进一出的程序 [打印本页]

作者: 101113b 时间: 2018-4-23 14:02
标题: STM8控制HDMID三进一出的程序
/**
  ******************************************************************************
  * @file Project/main.c
  * @author  MCD Application Team
  * @version V2.1.0
  * @date 18-November-2011
  * @brief Main program body
  ******************************************************************************
  * @attention
  *
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
  *
  * <h2><center>© COPYRIGHT 2011 STMicroelectronics</center></h2>
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "include.h"

/* Private defines -----------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/

void main(void)
{
Init_MCU_CLK();
Init_MCU_GPIO();
TIM4_Init();
LT8631UX_Reset();
Init_Lt8631UX_State();
  /* Infinite loop */
  while (1)
  {
    Rx_5V_Change_Detect();
Tx_Hpd_Change_Detect();
Hdmi20_Change_Detect();
Key_Process();
IR_Process();
//if((Flag_Switch_Key_Down||Flag_Rx_5V_Change||Flag_TX_Hpd_High||Flag_Hdmi20_Change)&&Number_Rx_Plug&&Flag_Tx_Hpd_Change) // ljy 20180421
   // ljy 20180421 start
   if(starting_up_on==1&&Number_Rx_Plug&&Flag_Tx_Hpd_Change)
      {
   Channel_Num_Current=1;
   starting_up_on=2;
      }
// ljy 20180421 end
if((Flag_Switch_Key_Down||starting_up_on==2)&&Number_Rx_Plug&&Flag_Tx_Hpd_Change) // ljy 20180421
{
if(Flag_Hdmi20)
{
Rx_Eq_Mode_Config(RX_FIXED_EQ,RX_EQ_VALUEA);
if(Flag_Switch_Key_Down||Flag_Rx_5V_Change)
{
Hdmi20_LT8631UX_Ch_Select(Channel_Num_Current);
}
else
{
LT8631UX_Ch_Select(Channel_Num_Current);//通道选择以及配置
}
}
else
{
Rx_Eq_Mode_Config(RX_FIXED_EQ,RX_EQ_VALUE5);
LT8631UX_Ch_Select(Channel_Num_Current);//通道选择以及配置
}
Flag_Rx_5V_Change=FALSE;
Flag_TX_Hpd_High=FALSE;
Flag_Switch_Key_Down=FALSE;
Flag_Hdmi20_Change=FALSE;
starting_up_on=0; // ljy 20180421
}
  }

}

#ifdef USE_FULL_ASSERT

/**
  * @brief  Reports the name of the source file and the source line number
  * where the assert_param error has occurred.
  * @param file: pointer to the source file name
  * @param line: assert_param error line source number
  * @retval : None
  */
void assert_failed(u8* file, u32 line)
{
  /* User can add his own implementation to report the file name and line number,
   ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */

  /* Infinite loop */
  while (1)
  {
  }
}
#endif

/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

欢迎光临 (http://www.51hei.com/bbs/)