大神帮助为什么ds1302能不能被读取 -

标题: 大神帮助为什么ds1302能不能被读取 [打印本页]

作者: 鐡人 时间: 2018-8-7 13:24
标题: 大神帮助为什么ds1302能不能被读取
不能读取ds1302的数据，.h文件没有问题
主程序代码在最下面

#include<reg52.h>
#include<lcd.h>
#include<i2c.h>
#include<intrins.h>
#include<stdio.h>
#include<ds1302.h>
typedef unsigned char uint8;
typedef unsigned int uint16;
sbit led1=P2^2;
sbit led2=P2^3;
sbit led3=P2^4;
uint8 num,num4,num5,key,mode,w;
uint16 i,j,m=0;
uint16 n=0;
uint8 a,b,c,d,e,f,g;
uint8 a1=1,a2=2,a3=3,a4=4,a5=5,a6=6;
uint8 x1=4,x2=5,x3=6,x4=7,x5=8,x6=9;
uint8 y1=6,y2=5,y3=4,y4=3,y5=2,y6=1;
uint8 z1=9,z2=8,z3=7,z4=6,z5=5,z6=4;
uint8 b1,b2,b3,b4,b5,b6;
uint8 dat1[]={1,2,3,4,5,6,7,8,9,0};
uint8 flag,r;
uint8 Q1,Q2,Q3,Q4,Q5,Q6;
uint8 L1,L2,L3,L4,L5,L6;
uint8 O1,O2,O3,O4,O5,O6;
uint8 U1,U2,U3,U4,U5,U6;
uint8 code table[]="open box";
uint8 Dispkaiji1[]="1.PASSWORD";
uint8 Dispkaiji2[]="2.IC";
uint8 cuowu1[]="  WRONG NUMBER  ";
uint8 cuowu2[]=" TRY AGAIN! ";
uint8 Dispjiesuo1[]=" UNLOCKED ";
uint8 Dispjiesuo2[]=" SUCCESSFULLY!! ";
uint8 suosi[]=" DEADLOCK ";
uint8 xiugai1[]="INPUT OLD NUMBER";
uint8 xiugai2[]="INPUT NEW NUMBER";
uint8 xiugai3[]="ALREADY CHANGED!";
uint8 box1[]=" BOX1  UNLOCKED ";
uint8 box2[]=" BOX2  UNLOCKED ";
uint8 box3[]=" BOX3  UNLOCKED ";
uint8 box4[]=" BOX4  UNLOCKED ";

void delay(uint16 i)
{
while(i--);
}
void delay2s()
{
unsigned char x,y,z;
for(x=127;x>0;x--)
      for(y=235;y>0;y--)
         for(z=32;z>0;z--);
_nop_();  //if Keil,require use intrins.h
}
void password_input()       //½«ÃÜÂëÐ´ÈëEEPROM
{
if(w==1)
{
  At24c02Write(1,a1);
  delay(10000);
  Q1=At24c02Read(1);
  At24c02Write(2,a2);
  delay(10000);
  Q2=At24c02Read(2);
  At24c02Write(3,a3);
  delay(10000);
  Q3=At24c02Read(3);
  At24c02Write(4,a4);
  delay(10000);
  Q4=At24c02Read(4);
  At24c02Write(5,a5);
  delay(10000);
  Q5=At24c02Read(5);
  At24c02Write(6,a6);
  delay(10000);
  Q6=At24c02Read(6);
}
if(w==4)
{
  At24c02Write(19,z1);
  delay(10000);
  U1=At24c02Read(19);
  At24c02Write(20,z2);
  delay(10000);
  U2=At24c02Read(20);
  At24c02Write(21,z3);
  delay(10000);
  U3=At24c02Read(21);
  At24c02Write(22,z4);
  delay(10000);
  U4=At24c02Read(22);
  At24c02Write(23,z5);
  delay(10000);
  U5=At24c02Read(23);
  At24c02Write(24,z6);
  delay(10000);
  U6=At24c02Read(24);
}
}

void password_output()       //½«ÃÜÂëÐ´ÈëEEPROM
{
  Q1=At24c02Read(1);a1=Q1;
  delay(10000);
  Q2=At24c02Read(2);a2=Q2;
  delay(10000);
  Q3=At24c02Read(3);a3=Q3;
  delay(10000);
  Q4=At24c02Read(4);a4=Q4;
  delay(10000);
  Q5=At24c02Read(5);a5=Q5;
  delay(10000);
  Q6=At24c02Read(6);a6=Q6;



  U1=At24c02Read(19);x1=U1;
  delay(10000);
  U2=At24c02Read(20);x2=U2;
  delay(10000);
  U3=At24c02Read(21);x3=U3;
  delay(10000);
  U4=At24c02Read(22);x4=U4;
  delay(10000);
  U5=At24c02Read(23);x5=U5;
  delay(10000);
  U6=At24c02Read(24);x6=U6;
}

void UsartInit()
{
SCON=0X50;
TMOD=0X20;
PCON=0X80;
TH1=0XF3;
TL1=0XF3;
ES=1;
EA=1;
TR1=1;
}
void delayms(uint16 xms)
{
uint16 i,j;
for(i=xms;i>0;i--)
  for(j=110;j>0;j--);
}

void LcdDisplayshijian()
{
Ds1302ReadTime();
LcdWriteCom(0x80+0X40);
LcdWriteData('0'+TIME[2]/16); //Ê±
LcdWriteData('0'+(TIME[2]&0x0f));
LcdWriteData('-');
LcdWriteData('0'+TIME[1]/16); //·Ö
LcdWriteData('0'+(TIME[1]&0x0f));
LcdWriteData('-');
LcdWriteData('0'+TIME[0]/16); //Ãë
LcdWriteData('0'+(TIME[0]&0x0f));
LcdWriteCom(0x80);
LcdWriteData('2');
LcdWriteData('0');
LcdWriteData('0'+TIME[6]/16); //Äê
LcdWriteData('0'+(TIME[6]&0x0f));
LcdWriteData('-');
LcdWriteData('0'+TIME[4]/16); //ÔÂ
LcdWriteData('0'+(TIME[4]&0x0f));
LcdWriteData('-');
LcdWriteData('0'+TIME[3]/16); //ÈÕ
LcdWriteData('0'+(TIME[3]&0x0f));
LcdWriteCom(0x8D);
LcdWriteData('0'+(TIME[5]&0x07)); //ÐÇÆÚ
}
void xianshi()
{
  Ds1302ReadTime();
  SBUF='2';while(TI==0);TI=0;
  SBUF='0';while(TI==0);TI=0;
  SBUF='0'+TIME[6]/16;while(TI==0);TI=0;
  SBUF='0'+(TIME[6]&0x0f);while(TI==0);TI=0;//nian
  SBUF='-';while(TI==0);TI=0;
  SBUF='0'+TIME[4]/16;while(TI==0);TI=0;
  SBUF='0'+(TIME[4]&0x0f);while(TI==0);TI=0;//yue
  SBUF='-';while(TI==0);TI=0;
  SBUF='0'+TIME[3]/16;while(TI==0);TI=0;
  SBUF='0'+(TIME[3]&0x0f);while(TI==0);TI=0;//ri
  SBUF='-';while(TI==0);TI=0;
  SBUF='-';while(TI==0);TI=0;
  SBUF='0'+TIME[2]/16;while(TI==0);TI=0;
  SBUF='0'+(TIME[2]&0x0f);while(TI==0);TI=0;//shi
  SBUF='-';while(TI==0);TI=0;
  SBUF='0'+TIME[1]/16;while(TI==0);TI=0;
  SBUF='0'+(TIME[1]&0x0f);while(TI==0);TI=0;//fen
  SBUF='-';while(TI==0);TI=0;
  SBUF='0'+TIME[0]/16;while(TI==0);TI=0;
  SBUF='0'+(TIME[0]&0x0f);while(TI==0);TI=0;//miao
  SBUF=' ';while(TI==0);TI=0;
}

void caiji1()
{
  if(n==1)
  {
a=g;
  }
  if(n==2)
  {
b=g;
  }
  if(n==3)
  {
c=g;
  }
  if(n==4)
  {
d=g;
  }
  if(n==5)
  {
e=g;
  }
  if(n==6)
  {
f=g;
  }
}
void caiji2()
{
  if(n==1)
  {
b1=g;
  }
  if(n==2)
  {
b2=g;
  }
  if(n==3)
  {
b3=g;
  }
  if(n==4)
  {
b4=g;
  }
  if(n==5)
  {
b5=g;
  }
  if(n==6)
  {
b6=g;
  }
}
void panduan()
{
switch(r)
{
  case(1):
  xianshi();
  for(i=0;i<8;i++)
{
SBUF=table[i];
while(!TI);
TI=0;
}
  SBUF='1';while(TI==0);TI=0;
  SBUF=0x0d;while(TI==0);TI=0;
  SBUF=0x0a;while(TI==0);TI=0;break;
  case(2):
  xianshi();
  for(i=0;i<8;i++)
{
SBUF=table[i];
while(!TI);
TI=0;
}SBUF='2';while(TI==0);TI=0;
  SBUF=0x0d;while(TI==0);TI=0;
  SBUF=0x0a;while(TI==0);TI=0;break;
  case(3):
  xianshi();
  for(i=0;i<8;i++)
{
SBUF=table[i];
while(!TI);
TI=0;
}SBUF='3';while(TI==0);TI=0;
  SBUF=0x0d;while(TI==0);TI=0;
  SBUF=0x0a;while(TI==0);TI=0;break;

  case(4):
  xianshi();
  for(i=0;i<8;i++)
{
SBUF=table[i];
while(!TI);
TI=0;
}SBUF='4';while(TI==0);TI=0;
  SBUF=0x0d;while(TI==0);TI=0;
  SBUF=0x0a;while(TI==0);TI=0;break;
}
}

void kaixiang()
{
            if((a1==a)&&(a2==b)&&(a3==c)&&(a4==d)&&(a5==e)&&(a6==f))
            {
               led1=0; r=1;
               m=0;
               n=0;
               a=10;
               LcdWriteCom(0x01);
               LcdWriteCom(0x80);
               for(i=0;i<16;i++)
               {
               LcdWriteData(box1[i]);
               }
               LcdWriteCom(0x80+0x40);
               for(j=0;j<16;j++)
               {
               LcdWriteData(Dispjiesuo2[j]);
               }
               mode=4;
            }                               //box1
            else if((x1==a)&&(x2==b)&&(x3==c)&&(x4==d)&&(x5==e)&&(x6==f))
            {
               led1=0; r=2;
               m=0;
               n=0;
               a=10;
               LcdWriteCom(0x01);
               LcdWriteCom(0x80);
               for(i=0;i<16;i++)
               {
               LcdWriteData(box2[i]);
               }
               LcdWriteCom(0x80+0x40);
               for(j=0;j<16;j++)
               {
               LcdWriteData(Dispjiesuo2[j]);
               }
               mode=4;
            }                               //box2
            else if((y1==a)&&(y2==b)&&(y3==c)&&(y4==d)&&(y5==e)&&(y6==f))
            {
               led1=0;r=3;
               m=0;
               n=0;
               a=10;
               LcdWriteCom(0x01);
               LcdWriteCom(0x80);
               for(i=0;i<16;i++)
               {
               LcdWriteData(box3[i]);
               }
               LcdWriteCom(0x80+0x40);
               for(j=0;j<16;j++)
               {
               LcdWriteData(Dispjiesuo2[j]);
               }
               mode=4;
            }                               //box3
            else if((z1==a)&&(z2==b)&&(z3==c)&&(z4==d)&&(z5==e)&&(z6==f))
            {
               led1=0;r=4;
               m=0;
               n=0;
               a=10;
               LcdWriteCom(0x01);
               LcdWriteCom(0x80);
               for(i=0;i<16;i++)
               {
               LcdWriteData(box4[i]);
               }
               LcdWriteCom(0x80+0x40);
               for(j=0;j<16;j++)
               {
               LcdWriteData(Dispjiesuo2[j]);
               }
               mode=4;
            }                               //box4
            else
            {
               m++;
               LcdWriteCom(0x01);
               LcdWriteCom(0x80);
               LcdWriteCom(0x80);
                  for(i=0;i<16;i++)
                  {
                  LcdWriteData(cuowu1[i]);
                  }
                  LcdWriteCom(0x80+0x40);
                  for(j=0;j<16;j++)
                  {
                  LcdWriteData(cuowu2[j]);
                  }

                  if(m==3)
                  {
                  LcdWriteCom(0x01);
                  while(1)
                  {
                  led2=0;
                  LcdWriteCom(0x80);
                  for(i=0;i<16;i++)
                  {
                     LcdWriteData(suosi[i]);
                  }
                  }
                  }
            }

}
void keyscan2()
{
P1=0x7f;
if(P1!=0x7f)
{
  delay(1000);
  if(P1!=0x7f)
  {
key=P1&0x0f;
switch(key)
{
case 0x07: num=0;n++;break;
case 0x0b: num=1;n++;break;
case 0x0d: num=2;n++;break;
}
  }
  while(P1!=0x7f);
  if(num==0)
  {
LcdWriteData(0x30+dat1[num]);
g=1;
  }
  if(num==1)
  {
LcdWriteData(0x30+dat1[num]);
g=2;
  }
  if(num==2)
  {
LcdWriteData(0x30+dat1[num]);
g=3;
  }
}

P1=0xbf;
if(P1!=0xbf)
{
  delay(1000);
  if(P1!=0xbf)
  {
key=P1&0x0f;
switch(key)
{
case 0x07: num=3;n++;break;
case 0x0b: num=4;n++;break;
case 0x0d: num=5;n++;break;
}
  }
  while(P1!=0xbf);
  if(num==3)
  {
LcdWriteData(0x30+dat1[num]);
g=4;
  }
  if(num==4)
  {
LcdWriteData(0x30+dat1[num]);
g=5;
  }
  if(num==5)
  {
LcdWriteData(0x30+dat1[num]);
g=6;
  }
}

P1=0xdf;
if(P1!=0xdf)
{
  delay(1000);
  if(P1!=0xdf)
  {
key=P1&0x0f;
switch(key)
{
case 0x07: num=6;n++;break;
case 0x0b: num=7;n++;break;
case 0x0d: num=8;n++;break;
}
  }
  while(P1!=0xdf);
  if(num==6)
  {
LcdWriteData(0x30+dat1[num]);
g=7;
  }
  if(num==7)
  {
LcdWriteData(0x30+dat1[num]);
g=8;
  }
  if(num==8)
  {
LcdWriteData(0x30+dat1[num]);
g=9;
  }
}

P1=0xef;
if(P1!=0xef)
{
  delay(1000);
  if(P1!=0xef)
  {
key=P1&0x0f;
switch(key)
{
case 0x0b : num=9;n++;break;
case 0x07 : num=10;break;
case 0x0d : num=11;break;
case 0x0e : mode=4;break;
}
  }
  while(P1!=0xef);
  if(num==9)
  {
LcdWriteData(0x30+dat1[num]);
g=0;
  }
  if(num==10)
  {
LcdWriteCom(0x01);
n=0;
a=b=c=d=e=f=0;
led1=1;
  }
            if(num==11)
            {
            if(mode==1)
            {
            kaixiang();
            flag=1;
            Ds1302ReadTime();
            if(flag==1)
               {
               ES=0;

               panduan();
               }
               ES=1;
            flag=0;
               //mode==1
            }
            if(mode==2)
            {
            }
            if(mode==3)
            {
            if((a1==a)&&(a2==b)&&(a3==c)&&(a4==d)&&(a5==e)&&(a6==f))
            {
               led1=0;
               LcdWriteCom(0x01);
               w=1;
            }
            if((x1==a)&&(x2==b)&&(x3==c)&&(x4==d)&&(x5==e)&&(x6==f))
            {
               led1=0;
               LcdWriteCom(0x01);
               w=2;
            }
            if((y1==a)&&(y2==b)&&(y3==c)&&(y4==d)&&(y5==e)&&(y6==f))
            {
               led1=0;
               LcdWriteCom(0x01);
               w=3;
            }
            if((z1==a)&&(z2==b)&&(z3==c)&&(z4==d)&&(z5==e)&&(z6==f))
            {
               led1=0;
               LcdWriteCom(0x01);
               w=4;
            }



            else
            {
               m++;
               LcdWriteCom(0x01);
               LcdWriteCom(0x80);
                  for(i=0;i<16;i++)
                  {
                  LcdWriteData(cuowu1[i]);
                  }
                  LcdWriteCom(0x80+0x40);
                  for(j=0;j<16;j++)
                  {
                  LcdWriteData(cuowu2[j]);
                  }
                  if(m==3)
                  {
                  LcdWriteCom(0x01);
                  while(1)
                  {
                  led2=0;
                  LcdWriteCom(0x80);
                  for(i=0;i<16;i++)
                  {
                     LcdWriteData(suosi[i]);
                  }
                  }
                  }
            }

            } //mode==3
            }
}
}
void keyscan3()
{
P1=0x7f;
if(P1!=0x7f)
{
  delay(1000);
  if(P1!=0x7f)
  {
key=P1&0x0f;
switch(key)
{
case 0x07: num=0;n++;break;
case 0x0b: num=1;n++;break;
case 0x0d: num=2;n++;break;
}
  }
  while(P1!=0x7f);
  if(num==0)
  {
LcdWriteData(0x30+dat1[num]);
g=1;
  }
  if(num==1)
  {
LcdWriteData(0x30+dat1[num]);
g=2;
  }
  if(num==2)
  {
LcdWriteData(0x30+dat1[num]);
g=3;
  }
}

P1=0xbf;
if(P1!=0xbf)
{
  delay(1000);
  if(P1!=0xbf)
  {
key=P1&0x0f;
switch(key)
{
case 0x07: num=3;n++;break;
case 0x0b: num=4;n++;break;
case 0x0d: num=5;n++;break;
}
  }
  while(P1!=0xbf);
  if(num==3)
  {
LcdWriteData(0x30+dat1[num]);
g=4;
  }
  if(num==4)
  {
LcdWriteData(0x30+dat1[num]);
g=5;
  }
  if(num==5)
  {
LcdWriteData(0x30+dat1[num]);
g=6;
  }
}

P1=0xdf;
if(P1!=0xdf)
{
  delay(1000);
  if(P1!=0xdf)
  {
key=P1&0x0f;
switch(key)
{
case 0x07: num=6;n++;break;
case 0x0b: num=7;n++;break;
case 0x0d: num=8;n++;break;
}
  }
  while(P1!=0xdf);
  if(num==6)
  {
LcdWriteData(0x30+dat1[num]);
g=7;
  }
  if(num==7)
  {
LcdWriteData(0x30+dat1[num]);
g=8;
  }
  if(num==8)
  {
LcdWriteData(0x30+dat1[num]);
g=9;
  }
}

P1=0xef;
if(P1!=0xef)
{
  delay(1000);
  if(P1!=0xef)
  {
key=P1&0x0f;
switch(key)
{
case 0x0b : num=9;n++;break;
case 0x07 : num=10;break;
case 0x0d : num=11;break;
case 0x0e : mode=4;break;
}
  }
  while(P1!=0xef);
  if(num==9)
  {
LcdWriteData(0x30+dat1[num]);
g=0;
  }
  if(num==10)
  {
LcdWriteCom(0x01);
n=0;
a=b=c=d=e=f=0;
led1=1;
  }
            if(num==11)
            {
            if(w==1)
            {
            a1=b1;
            a2=b2;
            a3=b3;
            a4=b4;
            a5=b5;
            a6=b6;
            }
            if(w==2)
            {
            x1=b1;
            x2=b2;
            x3=b3;
            x4=b4;
            x5=b5;
            x6=b6;
            }
            if(w==3)
            {
            y1=b1;
            y2=b2;
            y3=b3;
            y4=b4;
            y5=b5;
            y6=b6;
            }
            if(w==4)
            {
            z1=b1;
            z2=b2;
            z3=b3;
            z4=b4;
            z5=b5;
            z6=b6;
            }

            }
}
}
void chushi()
{
LcdWriteCom(0x80);
  for(i=0;i<10;i++)
  {
LcdWriteData(Dispkaiji1[i]);
  }
  LcdWriteCom(0x80+0x40);
  for(j=0;j<4;j++)
  {
LcdWriteData(Dispkaiji2[j]);
  }
}

void keyscan1()
{
while(1)
{
  chushi();



  P1=0x7f;
  if(P1!=0x7f)
  {
delay(1000);
if(P1!=0x7f)
{
key=P1&0x0f;
switch(key)
{
   case 0x0e: mode=1;break;
}
}
while(P1!=0x7f);
  }


P1=0xbf;
if(P1!=0xbf)
{
delay(1000);
if(P1!=0xbf)
{
   key=P1&0x0f;
   switch(key)
   {
   case 0x0e: mode=2;break;
   }
}

while(P1!=0xbf);
  }

P1=0xdf;
if(P1!=0xdf)
{
delay(1000);
if(P1!=0xdf)
{
   key=P1&0x0f;
   switch(key)
   {
   case 0x0e: mode=3;break;
   }
}

while(P1!=0xdf);
  }
if(mode==1)
{
   LcdWriteCom(0x01);

   while(1)
{
   caiji1();
   keyscan2();
   if(mode==4)
   {
   led1=1;
   n=0;
   delay2s();
   LcdWriteCom(0x01);
   break;
   }
}
}
if(mode==2)
   {
   }
if(mode==3)
{
         LcdWriteCom(0x01);
         while(1)
         {
         LcdWriteCom(0x80);
         for(i=0;i<16;i++)
         {
         LcdWriteData(xiugai1[i]); //old  number
         }
         break;
         }
         LcdWriteCom(0x80+0x40);
         while(1)
         {
         keyscan2();
         caiji1();

         if(mode==4)
         {
            led1=1;
            n=0;
            LcdWriteCom(0x01);
            break;
         }                            //fan hui

         if(led1==0)
         {
            n=0;

            break;
         }

         }

      if(led1==0)
         {
         LcdWriteCom(0x01);
         LcdWriteCom(0x80);
         for(i=0;i<16;i++)
         {
            LcdWriteData(xiugai2[i]);          //new number
         }
         led1=1;

         LcdWriteCom(0x80+0x40);
         while(1)
         {
         keyscan3();                         //
         caiji2();
         password_input();
         if(w==1)
         {
            if((a1==b1)&&(a2==b2)&&(a3==b3)&&(a4==b4)&&(a5==b5)&&(a6==b6))
            {
            LcdWriteCom(0x01);
            LcdWriteCom(0x80);
            for(i=0;i<16;i++)
            {
               LcdWriteData(xiugai3[i]);
            }
            mode=4;
            m=0;
            }
         }
         if(w==2)
         {
            if((x1==b1)&&(x2==b2)&&(x3==b3)&&(x4==b4)&&(x5==b5)&&(x6==b6))
            {
            LcdWriteCom(0x01);
            LcdWriteCom(0x80);
            for(i=0;i<16;i++)
            {
               LcdWriteData(xiugai3[i]);
            }
            mode=4;
            m=0;
            }
         }
         if(w==3)
         {
            if((y1==b1)&&(y2==b2)&&(y3==b3)&&(y4==b4)&&(y5==b5)&&(y6==b6))
            {
            LcdWriteCom(0x01);
            LcdWriteCom(0x80);
            for(i=0;i<16;i++)
            {
               LcdWriteData(xiugai3[i]);
            }
            mode=4;
            m=0;
            }
         }
         if(w==4)
         {
            if((z1==b1)&&(z2==b2)&&(z3==b3)&&(z4==b4)&&(z5==b5)&&(z6==b6))
            {
            LcdWriteCom(0x01);
            LcdWriteCom(0x80);
            for(i=0;i<16;i++)
            {
               LcdWriteData(xiugai3[i]);
            }
            mode=4;
            m=0;
            }
         }

         if(mode==4)
         {

            delay2s();delay2s();
            n=0;
            LcdWriteCom(0x01);
            break;

         }
         }
         }
}

  }
}

void main()
{
LcdInit();
UsartInit();
Ds1302Init();
while(1)
{
  LcdDisplayshijian();

  if(mode==4)
  {
mode=0;
led1=1;
n=0;
r=0;
LcdWriteCom(0x01);
while(1)
{
Ds1302ReadTime();
keyscan1();
}
  }
}
}

void Usart() interrupt 4
{
RI=0;
flag=1;
}

IMG_20180807_132032.jpg (2.26 MB, 下载次数: 37)

作者: fx283 时间: 2018-8-8 14:56
这么长的程序 ……怎么看得下去啊
对比一下这个板子给的例程

作者: 鐡人 时间: 2018-8-9 10:12

fx283 发表于 2018-8-8 14:56
这么长的程序 ……怎么看得下去啊
对比一下这个板子给的例程

ds1302 的.c .h 程序都是复制的没问题啊，就单独显示时钟是可以的，加到这个程序就不行了，串口发到电脑上也是？？？问号

作者: fzqiang 时间: 2018-8-9 10:40
程序有点儿长呀~~

作者: 011010 时间: 2018-8-9 10:52
不是这样的，用c

作者: yousunny 时间: 2018-8-9 11:13
你这样的开发版，应该有历程的，所以，找个历程下载进去，看下行不行。
然后，就是硬件问题了。我记得当时是那个芯片坏的，一直读取不了。然后，电池也是没电的，也是不行。

作者: 人中狼 时间: 2018-8-9 15:22
为什么没贴1302部分的程序呢，试试把1302部分的操作频率降低，有的1302芯片好像数据的时钟频率不能太高了

作者: 鐡人 时间: 2018-8-9 15:40

yousunny 发表于 2018-8-9 11:13
你这样的开发版，应该有历程的，所以，找个历程下载进去，看下行不行。
然后，就是硬件问题了。我记得当时 ...

单独1602显示可以的，加到我这个程序就不能显示了

作者: 鐡人 时间: 2018-8-10 09:37

人中狼发表于 2018-8-9 15:22
为什么没贴1302部分的程序呢，试试把1302部分的操作频率降低，有的1302芯片好像数据的时钟频率不能太高了

1302的程序就是复制的开发板历程里面的，我在1602单独显示或者串口传回电脑可以有1302的值，

作者: jipinxlm 时间: 2018-8-10 10:19
这么长的程序实在没耐心看完。。。我觉得写代码的时候应该先实现小的功能模块并测试OK然后再逐步增加其它功能模块，这样全部写完再测试根本没办法判断问题可能出现的地方，然后出错后可以用printf在特定位置打印代码，方便判断具体执行情况。

作者: 鐡人 时间: 2018-8-11 12:09

jipinxlm 发表于 2018-8-10 10:19
这么长的程序实在没耐心看完。。。我觉得写代码的时候应该先实现小的功能模块并测试OK然后再逐步增加其它功 ...

就是我所有模块都是好的，加起来有问题了

作者: Trump1438 时间: 2019-1-28 20:06
最好还是一种种功能来实验，先做好LCD1602，再DS1302,后AT2402.一口吃个大胖子不切实际！

欢迎光临 (http://www.51hei.com/bbs/)