请问，如何用stm32通过串口调试助手控制灯的亮灭？ -

标题: 请问，如何用stm32通过串口调试助手控制灯的亮灭？ [打印本页]

作者: stm32learning 时间: 2018-11-28 15:54
标题: 请问，如何用stm32通过串口调试助手控制灯的亮灭？

大家有没有源码可以分享

作者: 小猫猫爱吃鱼 时间: 2018-11-28 16:54

你好！
1、用的STM32的那款芯片？
2、分步完成程序和调试
a、写程序，先能点亮 led 灯
b、接着写程序，能用程序控制灯的亮灭
c、再写串口程序，能正常接收串口数据
d、增加串口控制指令，实现串口控制灯的亮灭
3、如有疑问，可以加我QQ好友，帮你完成设计

作者: yousunny 时间: 2018-11-29 09:07
用正点原子的历程，直接可以使用。具体你去官方论坛看下（开源电子网）（不做伸手党）

作者: alanqnb 时间: 2018-12-1 14:41
1.串口配置；2.串口中断接收；3.通过串口数据判断是否点亮led

作者: cyc0228 时间: 2018-12-1 16:29
#include "main.h"
#include "stm32f0xx_hal.h"

/* USER CODE BEGIN Includes */
#include "lcd.h"
/* USER CODE END Includes */

/* Private variables ---------------------------------------------------------*/
UART_HandleTypeDef huart1;

/* USER CODE BEGIN PV */
/* Private variables ---------------------------------------------------------*/

/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_USART1_UART_Init(void);

/* USER CODE BEGIN PFP */
/* Private function prototypes -----------------------------------------------*/

/* USER CODE END PFP */

/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

/**
  * @brief  The application entry point.
  *
  * @retval None
  */
int main(void)
{
  /* USER CODE BEGIN 1 */

  /* USER CODE END 1 */

  /* MCU Configuration----------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* USER CODE BEGIN Init */

  /* USER CODE END Init */

  /* Configure the system clock */
  SystemClock_Config();

  /* USER CODE BEGIN SysInit */

  /* USER CODE END SysInit */

  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_USART1_UART_Init();
  /* USER CODE BEGIN 2 */
Lcd_Init();
Lcd_Clear(WHITE);
  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
Gui_DrawFont_GBK16(0, 0, BLACK, WHITE, "LED1 OFF");
Gui_DrawFont_GBK16(0, 25, BLACK, WHITE, "LED2 OFF");
Gui_DrawFont_GBK16(0, 50, BLACK, WHITE, "LED3 OFF");
HAL_GPIO_WritePin(GPIOB, GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_2, GPIO_PIN_SET);
  while (1)
  {

  /* USER CODE END WHILE */

  /* USER CODE BEGIN 3 */

uint8_t data = 0;
HAL_UART_Receive_IT(&huart1, &data, 1);
if(data == '1')
{
HAL_GPIO_WritePin(GPIOB, GPIO_PIN_0, GPIO_PIN_RESET);
HAL_UART_Transmit(&huart1, &data, 1, 0);
Gui_DrawFont_GBK16(0, 0, BLACK, WHITE, "LED1  ON");
//HAL_Delay(500);
}
else if(data == '2')
{
HAL_GPIO_WritePin(GPIOB, GPIO_PIN_0, GPIO_PIN_SET);
HAL_UART_Transmit(&huart1, &data, 1, 0);
Gui_DrawFont_GBK16(0, 0, BLACK, WHITE, "LED1 OFF");
//HAL_Delay(500);
}
else if(data == '3')
{
HAL_GPIO_WritePin(GPIOB, GPIO_PIN_1, GPIO_PIN_RESET);
HAL_UART_Transmit(&huart1, &data, 1, 0);
Gui_DrawFont_GBK16(0, 25, BLACK, WHITE, "LED2  ON");
//HAL_Delay(500);
}
else if(data == '4')
{
HAL_GPIO_WritePin(GPIOB, GPIO_PIN_1, GPIO_PIN_SET);
HAL_UART_Transmit(&huart1, &data, 1, 0);
Gui_DrawFont_GBK16(0, 25, BLACK, WHITE, "LED2 OFF");
//HAL_Delay(500);
}
else if(data == '5')
{
HAL_GPIO_WritePin(GPIOB, GPIO_PIN_2, GPIO_PIN_RESET);
HAL_UART_Transmit(&huart1, &data, 1, 0);
Gui_DrawFont_GBK16(0, 50, BLACK, WHITE, "LED3  ON");
//HAL_Delay(500);
}
else if(data == '6')
{
HAL_GPIO_WritePin(GPIOB, GPIO_PIN_2, GPIO_PIN_SET);
HAL_UART_Transmit(&huart1, &data, 1, 0);
Gui_DrawFont_GBK16(0, 50, BLACK, WHITE, "LED3 OFF");
//HAL_Delay(500);
}
  }
  /* USER CODE END 3 */

}
---------------------
作者：乌云的暮年下着雪
来源：CSDN
原文：https://blog.csdn.net/qq_40390825/article/details/80994900
版权声明：本文为博主原创文章，转载请附上博文链接！

欢迎光临 (http://www.51hei.com/bbs/)