MSP430实现计时器的源代码 -

标题: MSP430实现计时器的源代码 [打印本页]

作者: 达达君 时间: 2018-11-30 22:08
标题: MSP430实现计时器的源代码
和上一篇文章一样，用到了 TM1638。计时器初值设为 23:57:45，计时到 23:59:59 时重置为 0点 0分 0秒。
（和上次的定时器一样，主函数中的delay是我自己写的，是为了便于调试，并没有真正起到延时1s的作用）

源の代码：

#include "TM1638.h"
#include "msp430f6638.h"
#include "stdint.h"

uint8_t num[8]; //各个数码管显示的值
uint8_t led_flag[8];
const uint8_t tab[] = {0x3F,0x06,0x5B,0x4F,0x66,0x6D,0x7D,0x07,0x7F,0x6F,0x77,0x7C,0x39,0x5E,0x79,0x00};

void init_port(void) {
P3DIR |= BIT5;
P3DIR |= BIT4 + BIT2;

P1DIR |= BIT0; // ACLK set out to pins
P1SEL |= BIT0;

}

const uint8_t tab2[] = {0x3F,0x06,0x5B,0x4F,0x66,0x6D,0x7D,0x07,0x7F,0x6F,0x77,0x7C,0x39,0x5E,0x79,0x71};

void TM1638_Write(unsigned char DATA) { //写数据函数
unsigned char i;
DIO_OUT;
for(i=0;i<8;i++) {
   CLK_low;
   if(DATA & 0x01)
      DIO_high;
   else
      DIO_low;
   CLK_high;
   DATA >>= 1;
}
}

unsigned char TM1638_Read(void) { //读数据函数
unsigned char i;
unsigned char temp=0;
DIO_IN;
STB_low;
for(i=0;i<8;i++) {
      temp >>= 1;
      CLK_low;
      _delay_us(100);
      if(DIO_READ)
            temp |= 0x80;
      else
            temp &= 0x7f;
      CLK_high;
}
return temp;
}

void Write_COM(unsigned char cmd) { //发送命令字
CLK_high;
STB_high;
STB_low;
TM1638_Write(cmd);
STB_high;
}

void Write_DATA(unsigned char add,unsigned char DATA) { //指定地址写入数据
Write_COM(0x44);
STB_low;
TM1638_Write(0xc0|add);
TM1638_Write(DATA);
STB_high;
}

void init_TM1638(void) {
unsigned char count = 0;
unsigned char times = 1;
while(times--) {
      Write_allLED(tab2[count]);
      count++;
      if(count == 16)
         count = 0;
      _delay_ms(100);
}
Write_allLED(0xff);
_delay_ms(100);
Write_allLED(0);
}

void delay() {
for (int i=0; i<10; i++)
   for (int j=0; j<1000; j++);
}

void Write_allLED(unsigned char DATA) {
unsigned char i;
Write_COM(0x8F);//显示控制
Write_COM(0x40); //数据命令
STB_low;
TM1638_Write(0xc0);
for(i=0;i<16;i++)
TM1638_Write(DATA);
STB_high;
}

void main(void) {

WDTCTL = WDTPW+WDTHOLD;
init_port();
init_TM1638();

int hourA = 2;
int hourB = 3;
int minuteA = 5;
int minuteB = 7;
int secondA = 4;
int secondB = 5;

while(1) {
      secondB++;
      if(secondB == 10) {
         secondB = 0;
         secondA++;
         if(secondA == 6) {
            secondA = 0;
            minuteB++;
            if(minuteB == 10) {
                  minuteB = 0;
                  minuteA++;
                  if(minuteA == 6) {
                     minuteA = 0;
                     hourB++;
                     if(hourB == 10) {
                        hourB = 0;
                        hourA++;
                     }
                     if(hourA == 2 && hourB == 4) {
                        hourA = 0;
                        hourB = 0;
                     }
                  }
            }
         }
      }

      Write_DATA(4*2,tab[hourA]);
      Write_DATA(5*2,tab[hourB]);
      Write_DATA(6*2,tab[15]);
      Write_DATA(7*2,tab[minuteA]);
      Write_DATA(0*2,tab[minuteB]);
      Write_DATA(1*2,tab[15]);
      Write_DATA(2*2,tab[secondA]);
      Write_DATA(3*2,tab[secondB]);

      delay();

}

}

shiy2-3-2.zip

1.95 KB, 下载次数: 5, 下载积分: 黑币 -5

作者: 刘旭0625 时间: 2018-12-30 16:36
很好，++++++

作者: 伊特 时间: 2019-8-7 08:50

刘旭0625 发表于 2018-12-30 16:36
很好，++++++

能不能给我发个定时一分钟灯亮的程序

欢迎光临 (http://www.51hei.com/bbs/)