我想用stc15单片机在1602上显示占空比，程序烧到板子上，1602上没数据，串口没错，... -

标题: 我想用stc15单片机在1602上显示占空比，程序烧到板子上，1602上没数据，串口没错，... [打印本页]

作者: 周涛1331 时间: 2019-7-23 09:55
标题: 我想用stc15单片机在1602上显示占空比，程序烧到板子上，1602上没数据，串口没错，...
#include"15.h"
#define uint unsigned int
#define uchar unsigned char

sbit lcden=P2^7;    //1602引脚
sbit lcdrw=P2^6;
sbit lcdrs=P2^5;

sbit s1=P2^0;    //按键
sbit s2=P2^1;
sbit s3=P2^2;

uchar zhankongbi=0x80;
uchar code table1[]="zhankongbi";
void delay(uint z);
void pwminit()                      //占空比初始化
{
            CMOD=0x02;
            CL=0x00;
            CH=0x00;
            PCA_PWM0=0x00;
            CCAPM0=0x42;
            CCAP0H=0xff;
            CCAP0L=0xff;
            CR=1;
}
void pwmshe(uchar t)//这是占空比调节函数
{

            CCAP0H=t;
            CCAP0L=t;
}
void write_com(uchar com)
{
lcdrs=0;
P0=com;
delay(5);
lcden=1;
delay(5);
lcden=0;
}
void write_data(uchar dota)
{
lcdrs=1;
P0=dota;
delay(5);
lcden=1;
delay(5);
lcden=0;
}
void initlcd()
{
lcden=0;
write_com(0x38);
delay(5);
write_com(0x0c); delay(5);
write_com(0x06);delay(5);
write_com(0x01);delay(5);
}
void display()
{
uchar num=0;
initlcd();
   write_com(0x80);
for(num=0;num<11;num++)
{
write_data(table1[num]);
delay(5);
}
}
void display1()
{

uint a=0,b=0,c=0;
      initlcd();
zhankongbi=zhankongbi/256*100;
a=zhankongbi/100;
b=zhankongbi%100/10;
c=zhankongbi%10;
write_com(0x80+0x40); delay(5);
write_data('a');
write_com(0x80+0x41);delay(5);
write_data('b');
write_com(0x80+0x42);delay(5);
write_data('c');
}
void keyscan()
{
if(s1==0)
{ delay(5);
if(s1==0)
{
   while(!s1);
      zhankongbi=zhankongbi-0x0a;
if(zhankongbi<10)
      zhankongbi=0x0a;
      pwmshe(zhankongbi);

}
}
if(s2==0)
{ delay(5);
if(s2==0)
{
while(!s2);
      zhankongbi=zhankongbi=0x0a;
if(zhankongbi>256)
zhankongbi=0x80;
      pwmshe(zhankongbi);

}
}
if(s3==0)
{
      delay(5);
if(s3==0)
{
        while(!s3);
   if(zhankongbi<20)
   zhankongbi++;
      zhankongbi--;
      pwmshe(zhankongbi);

}
}
}
void main()
{
P0M0 = 0x00;
P0M1 = 0x00;
P1M0 = 0x00;
P1M1 = 0x00;
P2M0 = 0x00;
P2M1 = 0x00;
P3M0 = 0x00;
P3M1 = 0x00;
P4M0 = 0x00;
P4M1 = 0x00;
P5M0 = 0x00;
P5M1 = 0x00;
P6M0 = 0x00;
P6M1 = 0x00;
P7M0 = 0x00;
P7M1 = 0x00;
   initlcd();
pwminit();
display();
display1();
while(1)
{
      keyscan();
}
}
void delay(uint z)
{
uint i,j;
for(i=z;i>=0;i--)
for(j=110;j>=0;j--);
}

作者: zhongya917 时间: 2019-7-23 10:43
建议先复位，另外检查下硬件电路确保硬件工作正常

作者: zhongya917 时间: 2019-7-23 10:51
板子是不是ok的？建议先写一些简单的底层驱动测试下硬件

作者: 小黑屋525 时间: 2019-7-23 12:47
哇哦，头文件就一个"15.h"这么简单？求教这块单片机

作者: 蓝天有梦 时间: 2019-7-23 19:45
建议先复位，另外检查下硬件电路确保硬件工作正常

作者: 周涛1331 时间: 2019-7-25 09:05
自己已解决；软件可能有点问题；
以下是程序：
#include"12.h"
#define  uint  unsigned int
#define  uchar  unsigned char

sbit lcden=P3^5;
sbit lcdrs=P3^7;
sbit lcdrw=P3^6;
sbit s1=P2^0;
sbit s2=P2^1;
float zhankongbi=256;
uchar code table1[]="zkb";
void display1();
void pwminit();
void keyscan();
void delay(uint z)
{
  uint i,j;
for(i=z;i>0;i--)
for(j=110;j>0;j--);
}

void pwminit()
{

            CMOD=0x04;
CCON=0X00;
            CL=0x00;
            CH=0x00;
// PCA_PWM0=0x00;
            CCAPM0=0x42;
            CCAP0H=0xff;
            CCAP0L=0xff;
            CR=1;
}
void pwmshe(uchar t)//这是占空比调节函数
{

            CCAP0H=t;
            CCAP0L=t;
}
void write_com(uchar com)// 液晶写命令函数
{
   lcdrs=0;
   lcdrw=0;
   P0=com;
   delay(5);
   lcden=1;
   delay(5);
   lcden=0;
}

void write_date(uchar date)//液晶写数据函数
{
   lcdrs=1;
   lcdrw=0;
   P0=date;
   delay(5);
   lcden=1;
   delay(5);
   lcden=0;
}
void init() //初始化函数
{
uchar num;

write_com(0x38);
write_com(0x0c);
write_com(0x06);
write_com(0x01);
write_com(0x80);//设置显示初始坐标
for(num=0;num<3;num++)//显示年月日
{
write_date(table1[num]);
delay(5);
}
}
void main()
{
P0M0 = 0x00;
P0M1 = 0x00;
P1M0 = 0x00;
P1M1 = 0x00;
P2M0 = 0x00;
P2M1 = 0x00;
P3M0 = 0x00;
P3M1 = 0x00;
P4M0 = 0x00;
P4M1 = 0x00;
P5M0 = 0x00;
P5M1 = 0x00;
init();
pwminit();
display1();
while(1) //进入主程序大循环
{

            keyscan();
   display1();
            pwmshe(zhankongbi);
}

}
void keyscan()
{
if(s1==0)
{
delay(60);
if(s1==0)
{
   while(!s1);
      zhankongbi--;


}
}
if(s2==0)
{
      delay(60);
if(s2==0)
{
while(!s2);
      zhankongbi++;
if(zhankongbi>256)
zhankongbi=0x80;
}
}

}
void display1(float m)
{

float a=0,c=0;
      uchar b=0;
      m=zhankongbi;
      m=(float)m*100/256;
      a=m/100;
      b=(uchar)m%100/10;
      c=(uchar)m%10;

write_com(0x84);
write_date(a+0x30);
write_com(0x85);
write_date(b+0x30);
write_com(0x86);
write_date(c+0x30);
write_com(0x87);
write_date('%');
write_com(0x83);
write_date(':');

}

作者: 周涛1331 时间: 2019-7-25 09:07
引脚同的原因是我拿12芯片做测试的；12和15芯片1602的读写，使能引脚不同

欢迎光临 (http://www.51hei.com/bbs/)