简易的引体向上计数器单片机红外对管测数程序 -

/*============================================================
/
==============================================================
SMC1602A(16*2)模拟口线接线方式
连接线图:
---------------------------------------------------
|LCM-----51 | LCM-----51 | LCM------51 |
--------------------------------------------------|
|DB0-----P1.0 | DB4-----P1.4 | RW-------P3.4 |
|DB1-----P1.1 | DB5-----P1.5 | RS-------P3.3 |
|DB2-----P1.2 | DB6-----P1.6 | E--------P3.5 |
|DB3-----P1.3 | DB7-----P1.7 | VLCD接1K电阻到GND|
---------------------------------------------------
接线：模块TRIG接 P2.6 ECH0 接P2.7
=============================================================*/
#include <AT89x51.H> //器件配置文件
#include <intrins.h>
#define Rin P3_7
#define LCM_RW P1_1 //定义LCD引脚
#define LCM_RS P1_0
#define LCM_E P1_5
#define LCM_Data P0
#define Key_Data P2_0 //定义Keyboard引脚
#define Key_CLK P3_2
#define Busy 0x80 //用于检测LCM状态字中的Busy标识
void LCMInit(void);
void DisplayOneChar(unsigned char X, unsigned char Y, unsigned char DData);
void DisplayListChar(unsigned char X, unsigned char Y, unsigned char code *DData);
void Delay5Ms(void);
void Delay400Ms(void);
void Decode(unsigned char ScanCode);
void WriteDataLCM(unsigned char WDLCM);
void WriteCommandLCM(unsigned char WCLCM,BuysC);
void Conut(void);
unsigned char ReadDataLCM(void);
unsigned char ReadStatusLCM(void);
unsigned char code mcustudio[] ={"number:"};
unsigned char code Cls[] = {" "};
unsigned char code ASCII[10] = {'0','1','2','3','4','5','6','7','8','9'};
static unsigned char DisNum = 0; //显示用指针
unsigned int time=0;
bit flag =0;
unsigned char disbuff[4]={ 0,0,0,0,};
unsigned long S = 0;
volatile bit FlagSucceed=0; //测量成功标志
sbit Beep=P2^0; //报警蜂鸣器
sbit LedAlarm = P2^1;
void WriteDataLCM(unsigned char WDLCM)
{
ReadStatusLCM(); //检测忙
LCM_Data = WDLCM;
LCM_RS = 1;
LCM_RW = 0;
LCM_E = 0; //若晶振速度太高可以在这后加小的延时
LCM_E = 0; //延时
LCM_E = 1;
}
//写指令
void WriteCommandLCM(unsigned char WCLCM,BuysC) //BuysC为0时忽略忙检测
{
if (BuysC) ReadStatusLCM(); //根据需要检测忙
LCM_Data = WCLCM;
LCM_RS = 0;
LCM_RW = 0;
LCM_E = 0;
LCM_E = 0;
LCM_E = 1;
}
//读数据
unsigned char ReadDataLCM(void)
{
LCM_RS = 1;
LCM_RW = 1;
LCM_E = 0;
LCM_E = 0;
LCM_E = 1;
return(LCM_Data);
}
//读状态
unsigned char ReadStatusLCM(void)
{
LCM_Data = 0xFF;
LCM_RS = 0;
LCM_RW = 1;
LCM_E = 0;
LCM_E = 0;
LCM_E = 1;
while (LCM_Data & Busy); //检测忙信号
return(LCM_Data);
}
void LCMInit(void) //LCM初始化
{
LCM_Data = 0;
WriteCommandLCM(0x38,0); //三次显示模式设置，不检测忙信号
Delay5Ms();
WriteCommandLCM(0x38,0);
Delay5Ms();
WriteCommandLCM(0x38,0);
Delay5Ms();
WriteCommandLCM(0x38,1); //显示模式设置,开始要求每次检测忙信号
WriteCommandLCM(0x08,1); //关闭显示
WriteCommandLCM(0x01,1); //显示清屏
WriteCommandLCM(0x06,1); // 显示光标移动设置
WriteCommandLCM(0x0F,1); // 显示开及光标设置
}
//按指定位置显示一个字符
void DisplayOneChar(unsigned char X, unsigned char Y, unsigned char DData)
{
Y &= 0x1;
X &= 0xF; //限制X不能大于15，Y不能大于1
if (Y) X |= 0x40; //当要显示第二行时地址码+0x40;
X |= 0x80; //算出指令码
WriteCommandLCM(X, 1); //发命令字
WriteDataLCM(DData); //发数据
}
//按指定位置显示一串字符
void DisplayListChar(unsigned char X, unsigned char Y, unsigned char code *DData)
{
unsigned char ListLength;
ListLength = 0;
Y &= 0xFE;
X &= 0xFF; //限制X不能大于15，Y不能大于1
while (DData[ListLength]>0x19) //若到达字串尾则退出
{
if (X <= 0xF) //X坐标应小于0xF
{
DisplayOneChar(X, Y, DData[ListLength]); //显示单个字符
ListLength++;
X++;
}
}
}
//5ms延时
void Delay5Ms(void)
{
unsigned int TempCyc = 5552;
while(TempCyc--);
}
//400ms延时
void Delay400Ms(void)
{
unsigned char TempCycA = 5;
unsigned int TempCycB;
while(TempCycA--)
{
TempCycB=7269;
while(TempCycB--);
};
}
/********************************************************/
void Conut(void)
{
time=TH0*256+TL0;
TH0=0;
TL0=0;
S+=1; //算出来是
Beep = 0;
if((S>=1000)||flag==1) //超出测量范围显示“-”
{
flag=0;
DisplayOneChar(0, 1, ASCII[0]);
DisplayOneChar(1, 1, ASCII[1]);
DisplayOneChar(2, 1, ASCII[2]);
}
else
{
disbuff[0]=S/100%10;
disbuff[1]=S/10%10;
disbuff[2]=S%10;
DisplayOneChar(0, 1, ASCII[disbuff[0]]);
DisplayOneChar(1, 1, ASCII[disbuff[1]]);
DisplayOneChar(2, 1, ASCII[disbuff[2]]);
}
}
/********************************************************/
void zd0() interrupt 1 //T0中断用来计数器溢出,超过测距范围
{
flag=1; //中断溢出标志
}
/********************************************************/
void StartModule() //启动模块
{
Rin=0; //启动一次模块
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
Rin=1;
}
/********************************************************/
void delayms(unsigned int ms)
{
unsigned char i=100,j;
for(;ms;ms--)
{
while(--i)
{
j=10;
while(--j);
}
}
}
/*********************************************************/
void main(void)
{
unsigned char TempCyc;
LedAlarm = 1;
Delay400Ms(); //启动等待，等LCM讲入工作状态
LCMInit(); //LCM初始化
Delay5Ms(); //延时片刻(可不要)
DisplayListChar(0, 0, mcustudio);
ReadDataLCM();//测试用句无意义
for (TempCyc=0; TempCyc<10; TempCyc++)
Delay400Ms(); //延时
while(1)
{
StartModule();
DisplayOneChar(0, 1, ASCII[0]);
while(!Rin); //当RX为零时等待
TR0=0; //关闭计数
Conut(); //计算
Beep = 1;
delayms(80); //80MS
while(Rin); //当RX为1计数并等待
EA=0;
//以下为一次检测过程；先发出Trin电平，打开外部中断，清零T1
//最后在外部中断下降沿触发时取出T1当前值，计算出Trig脉冲宽度
TR0=1; //开启计数
Beep = 0;
}
}

复制代码