STM32F103+RF（SI443 SI4463 SX1278扩频）+OLED+串口+按键+温湿度传感器 -

/**********************(C) COPYRIGHT tongxinmao*****************************
* 文件名 : main.c
* 描述 : 主文件 STM32F103C8T6+RF（SI443 SI4463 SX1278扩频）+OLED+串口+按键+温湿度传感器
* 历史记录 : 暂无
* 使用说明：按键S1 短按切换无线是否应答，长按清空收发计数 S2：单次发送 S3:连续发送50*n次
发送的数据为温湿度数据，接收方收到后显示
********************************************************************************/
/*--------------------------- 头文件包含 --------------------------------------*/
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include "main.h"
#include "function.h"
#include "oled.h"
#include "usart1.h"
#include "gpio.h"
#include "Delay.h"
#include "timeget.h"
#include "rf.h"
/*-----------------------------------------------------------------------------*/
/*
* #pragma diag_suppress 77,550,1294,1295
* #pragma diag_suppress 870
*/
#pragma diag_suppress 870
/*
* ------------------------------------------------------------------------
* ------------------------------------------------------------------------
* -------------------- 宏定义 ------------------------------
* ------------------------------------------------------------------------
* ------------------------------------------------------------------------
*/
#define CMD_TEMP_HUM 1
#define CMD_ACK 2
/*
* ------------------------------------------------------------------------
* ------------------------------------------------------------------------
* -------------------- 变量定义 ------------------------------
* ------------------------------------------------------------------------
* ------------------------------------------------------------------------
*/
u16 Counter=0,Msec=0;
u8 Counterflg=0;
/*
* ------------------------------------------------------------------------
* ------------------------------------------------------------------------
* -------------------- 函数声明 ------------------------------
* ------------------------------------------------------------------------
* ------------------------------------------------------------------------
*/
void frameProcess( u8 *buf, u8 size )
{
u8 cmd = buf[0];
u8 len = buf[1];
switch ( cmd )
{
case CMD_TEMP_HUM:
if ( rfAck )
{
sendBuf[0] = CMD_ACK;
sendBuf[1] = 0;
RFSendData( sendBuf, 2 );
msg( "回复应答..." );
}
/* 显示温湿度数据 */
if ( len == 4 )
{
memcpy( &temp, buf + 2, 2 );
memcpy( &hum, buf + 4, 2 );
msg( "收到温湿度数据" );
}
break;
case CMD_ACK:
/* 屏幕显示应答成功 */
msg( "收到应答" );
break;
default:
break;
}
}
void revieveProcess( u8 *buf, u8 size )
{
u8 i=0;
for(i=0;i<=size;i++)
{
printf(" %d",buf[i]);
}
printf("\r\n");
}
/**************************************************************
* 函数名 : main()
* 描述 : 主函数
*************************************************************/
int main( void )
{
char buf[64] = "";
/* --配置系统主频为72MHz */
SystemInit();
Delay_InitConfig( 72 );
GPIOInit(); //GPIO初始化
OLED_Init(); //OLED初始化
Uart1Init(); //串口初始化用于输出调试信息 9600bps 8N1
TIM3_Int_Init(9999,7199);
RFInit(); //射频模块初始化
RFRxMode(); //进入接收模式
msg( "TIME 1S TEST" );
getTempHum(); //获取温湿度数据
while ( 1 )
{
int len;
sprintf( buf, "%s %s", rfName, rfAck ? "SLAVE" : "MASTER" );
OLED_PXx16MixStr( 0, 0, buf );
getTempHum(); //获取温湿度数据
sprintf( buf, "温湿度%.1f %.1f%%", temp / 10.0, hum / 10.0 );
OLED_PXx16MixStr( 0, 1, buf );
if(Counterflg==1)
{
Counterflg=0;
printf("\r\n");
printf( "本机温度：%.1f 本机湿度：%.1f%%", temp / 10.0, hum / 10.0 );
printf("\r\n");
}
len = RFRevData( revBuf ); //接收无线数据
if ( len > 0 )
{
// revieveProcess( revBuf, len ); //数据处理
printf("\r\n");
printf("当前收到秒数：%d",revBuf[0]);
printf("\r\n");
if(revBuf[0]<10) //清除一下显示花屏
{
sprintf( buf, " ");
OLED_PXx16MixStr( 0, 2, buf );
}
sprintf( buf, "收到 %d SEC %d", iRev, revBuf[0] );
OLED_PXx16MixStr( 0, 2, buf );
}
}
/* while ( 1 )
{
sprintf( buf, "%s %s", rfName, rfAck ? "MASTER " : "SLAVE" );
OLED_PXx16MixStr( 0, 0, buf );
if(Counterflg==1)
{
Counterflg=0;
sendBuf[0] = Msec;
sendBuf[1] = 0;
RFSendData( sendBuf, 2 );
sprintf( buf, "SEND %d SEC %d", iSend, Msec );
printf(" %d, %d",iSend,Msec);
printf("\r\n");
OLED_PXx16MixStr( 0, 2, buf );
}
}*/
/* while ( 1 )
{
int len;
keyProcess(); //按键检测处理
led_blink(); //led运行灯闪烁
len = RFRevData( revBuf ); //接收无线数据
if ( len > 0 )
{
frameProcess( revBuf, len ); //数据处理
}
if(rfContinueSend())
{
Delay_ms( 500 );
}
OledDisplay(); //刷新OLED显示
} */
}
/*
* ------------------------------------------------------------------------
* ------------------------------------------------------------------------
* -------------------- 公有函数定义 ------------------------------
* ------------------------------------------------------------------------
* ------------------------------------------------------------------------
*/
/* end of main.c -------------------------------------------------------------*/

复制代码