uvision4总出错，麻烦说的清楚一点，我是学渣我真的不会啊 -

#include <STC12C2052AD.H>
#include <intrins.h>
#define uc unsigned char
#define ut unsigned int
#define FOSC 11059200L //系统频率
#define BAUD 9600 //串口波特率
#define T1MS 1536 //1ms定时器
//宏定义ADC的操作命令
#define ADC_POWER 0x80 //ADC电源控制位
#define ADC_START 0x08 //ADC启动控制位
#define ADC_FLAG 0x10 //ADC完成标志位
#define ADC_SPEEDLL 0x00 //420时钟速度控制位
//#define unsigned int p3
sbit relay = P3^7;//继电器输出
sbit touch = P1^0;//触摸检测
uc sec,temp;
ut milsec;
void delay(uc i)
{
while(i) i--;
}
void InitUart(void);
void InintTimer0(void);
void InitADC(void);
uc GetADCResult(uc ch);
void main()
{
bit chanal;
ut save_times,light,voice;
AUXR=0x00;
InintTimer0();
InitADC();
sec=0;
relay=0;
while(1)
{
if(chanal)
{
light+=GetADCResult(2);//光照强度检测
save_times++;
}
else
{
voice+=GetADCResult(6);//声音分贝检测
}
chanal=~chanal;
if(save_times==256) //消抖
{
save_times=0;
light/=256;
voice/=256;
}
if((light>200)||(voice>50)||(touch==0))relay=1;
if(sec>=20)relay=0; //延时输出20秒后灭灯
delay(200);
delay(200);
}
}
/*
void InitUart(void)
{
SCON=0x50; //8个数据位，无校验
TMOD|=0x20; //8位自动装载
TH1=TL1=-(FOSC/12/32/BAUD);//设置波特率
TR1=1; //使能定时1
}
*/
void InintTimer0(void)
{
TMOD|=0x01;
TL0=T1MS;
TH0=T1MS>>8;
TR0=1;
ET0=1;
EA=1;
}
void InitADC(void)
{
P1=P1M0=0xff;
P1M1=0x00;
ADC_DATA=0;
ADC_CONTR=ADC_POWER|ADC_SPEEDLL;
delay(2);
}
uc GetADCResult(uc ch)
{
ADC_CONTR=ADC_POWER|ADC_SPEEDLL|ch|ADC_START;
_nop_();
_nop_();
_nop_();
_nop_();
while(!(ADC_CONTR & ADC_FLAG));//Wait complete flag
ADC_CONTR &=~ADC_FLAG;
return ADC_DATA;
}
void tm0_isr() interrupt 1 using 1
{
TL0=T1MS;
TH0=T1MS>>8;
milsec++;
if(milsec==1000)
{
if(sec<20)sec++;
}
}

复制代码

#ifndef __STC12C2052AD_H_
#define __STC12C2052AD_H_
/////////////////////////////////////////////////
/* The following is STC additional SFR or change */
/* sfr AUXR = 0x8e; */
/* sfr IPH = 0xb7; */
/* Watchdog Timer Register */
sfr WDT_CONTR = 0xe1;
/* ISP_IAP_EEPROM Register */
sfr ISP_DATA = 0xe2;
sfr ISP_ADDRH = 0xe3;
sfr ISP_ADDRL = 0xe4;
sfr ISP_CMD = 0xe5;
sfr ISP_TRIG = 0xe6;
sfr ISP_CONTR = 0xe7;
/* IDLE, Clock Divider */
sfr IDLE_CLK = 0xc7;
sfr WAKE_CLKO = 0x8F;
/* I_O Port Mode Set Register */
sfr P0M0 = 0x93;
sfr P0M1 = 0x94;
sfr P1M0 = 0x91;
sfr P1M1 = 0x92;
sfr P2M0 = 0x95;
sfr P2M1 = 0x96;
sfr P3M0 = 0xb1;
sfr P3M1 = 0xb2;
/* SPI Register */
sfr SPSTAT = 0x84;
sfr SPCTL = 0x85;
sfr SPDAT = 0x86;
/* ADC Register */
sfr ADC_CONTR = 0xc5;
sfr ADC_DATA = 0xc6;
sfr ADC_LOW2 = 0xbe;
/* PCA SFR */
sfr CCON = 0xD8;
sfr CMOD = 0xD9;
sfr CCAPM0 = 0xDA;
sfr CCAPM1 = 0xDB;
sfr CCAPM2 = 0xDC;
sfr CCAPM3 = 0xDD;
sfr CCAPM4 = 0xDE;
sfr CCAPM5 = 0xDF;
sfr CL = 0xE9;
sfr CCAP0L = 0xEA;
sfr CCAP1L = 0xEB;
sfr CCAP2L = 0xEC;
sfr CCAP3L = 0xED;
sfr CCAP4L = 0xEE;
sfr CCAP5L = 0xEF;
sfr CH = 0xF9;
sfr CCAP0H = 0xFA;
sfr CCAP1H = 0xFB;
sfr CCAP2H = 0xFC;
sfr CCAP3H = 0xFD;
sfr CCAP4H = 0xFE;
sfr CCAP5H = 0xFF;
sfr PCA_PWM0 = 0xF2;
sfr PCA_PWM1 = 0xF3;
sfr PCA_PWM2 = 0xF4;
sfr PCA_PWM3 = 0xF5;
sfr PCA_PWM4 = 0xF6;
sfr PCA_PWM5 = 0xF7;
/* CCON */
sbit CF = CCON^7;
sbit CR = CCON^6;
sbit CCF5 = CCON^5;
sbit CCF4 = CCON^4;
sbit CCF3 = CCON^3;
sbit CCF2 = CCON^2;
sbit CCF1 = CCON^1;
sbit CCF0 = CCON^0;
/* Above is STC additional SFR or change */
/*--------------------------------------------------------------------------
REG51F.H
Header file for 8xC31/51, 80C51Fx, 80C51Rx+
Modification according to DataSheet from April 1999
- SFR's AUXR and AUXR1 added for 80C51Rx+ derivatives
--------------------------------------------------------------------------*/
/* BYTE Registers */
sfr P0 = 0x80;
sbit P00 = P0^0;
sbit P01 = P0^1;
sbit P02 = P0^2;
sbit P03 = P0^3;
sbit P04 = P0^4;
sbit P05 = P0^5;
sbit P06 = P0^6;
sbit P07 = P0^7;
sfr P1 = 0x90;
sbit P10 = P1^0;
sbit P11 = P1^1;
sbit P12 = P1^2;
sbit P13 = P1^3;
sbit P14 = P1^4;
sbit P15 = P1^5;
sbit P16 = P1^6;
sbit P17 = P1^7;
sfr P2 = 0xA0;
sbit P20 = P2^0;
sbit P21 = P2^1;
sbit P22 = P2^2;
sbit P23 = P2^3;
sbit P24 = P2^4;
sbit P25 = P2^5;
sbit P26 = P2^6;
sbit P27 = P2^7;
sfr P3 = 0xB0;
sbit P30 = P3^0;
sbit P31 = P3^1;
sbit P32 = P3^2;
sbit P33 = P3^3;
sbit P34 = P3^4;
sbit P35 = P3^5;
sbit P36 = P3^6;
sbit P37 = P3^7;
sfr PSW = 0xD0;
sfr ACC = 0xE0;
sfr B = 0xF0;
sfr SP = 0x81;
sfr DPL = 0x82;
sfr DPH = 0x83;
sfr PCON = 0x87;
sfr TCON = 0x88;
sfr TMOD = 0x89;
sfr TL0 = 0x8A;
sfr TL1 = 0x8B;
sfr TH0 = 0x8C;
sfr TH1 = 0x8D;
sfr IE = 0xA8;
sfr IP = 0xB8;
sfr SCON = 0x98;
sfr SBUF = 0x99;
/* 80C51Fx/Rx Extensions */
sfr AUXR = 0x8E;
/* sfr AUXR1 = 0xA2; */
sfr SADDR = 0xA9;
sfr IPH = 0xB7;
sfr SADEN = 0xB9;
sfr T2CON = 0xC8;
sfr T2MOD = 0xC9;
sfr RCAP2L = 0xCA;
sfr RCAP2H = 0xCB;
sfr TL2 = 0xCC;
sfr TH2 = 0xCD;
/* BIT Registers */
/* PSW */
sbit CY = PSW^7;
sbit AC = PSW^6;
sbit F0 = PSW^5;
sbit RS1 = PSW^4;
sbit RS0 = PSW^3;
sbit OV = PSW^2;
sbit P = PSW^0;
/* TCON */
sbit TF1 = TCON^7;
sbit TR1 = TCON^6;
sbit TF0 = TCON^5;
sbit TR0 = TCON^4;
sbit IE1 = TCON^3;
sbit IT1 = TCON^2;
sbit IE0 = TCON^1;
sbit IT0 = TCON^0;
/* P3 */
sbit RD = P3^7;
sbit WR = P3^6;
sbit T1 = P3^5;
sbit T0 = P3^4;
sbit INT1 = P3^3;
sbit INT0 = P3^2;
sbit TXD = P3^1;
sbit RXD = P3^0;
/* SCON */
sbit SM0 = SCON^7; // alternatively "FE"
sbit FE = SCON^7;
sbit SM1 = SCON^6;
sbit SM2 = SCON^5;
sbit REN = SCON^4;
sbit TB8 = SCON^3;
sbit RB8 = SCON^2;
sbit TI = SCON^1;
sbit RI = SCON^0;
sbit T2EX = P1^1;
sbit T2 = P1^0;
/* T2CON */
sbit TF2 = T2CON^7;
sbit EXF2 = T2CON^6;
sbit RCLK = T2CON^5;
sbit TCLK = T2CON^4;
sbit EXEN2 = T2CON^3;
sbit TR2 = T2CON^2;
sbit C_T2 = T2CON^1;
sbit CP_RL2= T2CON^0;
/* PCA Pin */
sbit CEX3 = P2^4;
sbit CEX2 = P2^0;
sbit CEX1 = P3^5;
sbit CEX0 = P3^7;
sbit ECI = P3^4;
/* IE */
sbit EA = IE^7;
sbit EPCA_LVD = IE^6;
sbit EADC_SPI = IE^5;
sbit ES = IE^4;
sbit ET1 = IE^3;
sbit EX1 = IE^2;
sbit ET0 = IE^1;
sbit EX0 = IE^0;
/* IP */
sbit PPCA_LVD = IP^6;
sbit PADC_SPI = IP^5;
sbit PS = IP^4;
sbit PT1 = IP^3;
sbit PX1 = IP^2;
sbit PT0 = IP^1;
sbit PX0 = IP^0;
/////////////////////////////////////////////////
#endif

复制代码