标题: 最新版单片机光立方制作资料 [打印本页]

---

作者: kebo    时间: 2022-4-25 23:53
标题: 最新版单片机光立方制作资料
全在附件里面，包括光立方原理图，源程序，取模软件，上位机软件，相关文档==，想要的东西基本在里面了，已经测试过没有问题。

电路原理图如下：


单片机源程序如下:

1. /*---------------------------------------------------------------------------------------------------
   
2. * 上升沿电子
   
3. -----------------------------------------------------------------------------------------------------*/
   
4. 
   
5. //Build target 'Target 1'
   
6. //compiling stc8x8x8.c...
   
7. //linking...
   
8. //Program Size: data=17.1 xdata=355 code=53475
   
9. //creating hex file from "stc8x8x8"...
   
10. //"stc8x8x8" - 0 Error(s), 0 Warning(s).
    
11. //没有关闭店字样的显示函数 FLASH_12        FLASH_14  FLASH_18 如果需要自己关闭函数即可
    
12. 
    
13. 
    
14. 
    
15. 
    
16. 
    
17. #include "STC12C5A.H"  //包含单片机的头文件使用KEIL必须添加进来否则编译不了
    
18. #include "intrins.h"   //包含NOP延时头文件
    
19. #define uchar unsigned char         
    
20. #define uint unsigned int         
    
21. #define nop() _nop_();_nop_();
    
22. 
    
23. void key_baihei_scan();  
    
24. void key_shangwiej_scan();   
    
25. void key_donghua_scan();        
    
26. void key_yinyue_scan();
    
27. void box(unsigned char x1,unsigned char z1,unsigned char y1,unsigned char x2,unsigned char z2,unsigned char y2,unsigned char fill,unsigned char le);
    
28. /*@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@*/
    
29. sbit AD=P1^0;                 //定义音频输入接口
    
30. sbit GM=P1^1;                 //定义光敏输入接口
    
31. 
    
32. sbit K1=P0^0;                 //定义功能按键接口
    
33. sbit K2=P0^1;                 //定义功能按键接口
    
34. sbit K3=P0^2;                 //定义功能按键接口
    
35. sbit K4=P0^3;                 //定义功能按键接口
    
36. 
    
37. sbit PWM_POW=P4^4;   //定义PWM呼吸小夜灯和主板电源指示灯功能接口 低电平
    
38. sbit IRIN=P3^2;           //红外线信号接口
    
39. 
    
40. /*@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@*/
    
41. sbit M_HR_DS0=P1^4;          //模拟数据发送端口
    
42. sbit M_LR_DS0=P1^5;          //模拟数据发送端口
    
43. 
    
44. 
    
45. sbit M_HG_DS0=P1^6;          //模拟数据发送端口
    
46. sbit M_LG_DS0=P0^7;          //模拟数据发送端口
    
47. 
    
48. sbit CLK=P1^3;    //模拟时钟控制端口
    
49. sbit SUO=P1^2;          //模拟锁存信号端口
    
50. /*$-_-$_-_$-_-$_-_$-_-$_-_$-_-$_-_$-_-$_-_$-_-$_-_$-_-$_-_$-_-$_-_$-_-$_-_$-_-$_-_$*/
    
51. 
    
52. sbit M_A=P3^4;          //行数据扫描信号
    
53. sbit M_B=P3^5;          //行数据扫描信号
    
54. sbit M_C=P3^6;          //行数据扫描信号
    
55. sbit M_D=P3^7;          //行数据扫描信号
    
56. sbit M_EN=P1^7;   //行数据扫描信号
    
57. /*@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@*/
    
58. unsigned char displayck[]=
    
59. {
    
60. 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    
61. 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    
62. 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    
63. 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    
64. 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    
65. 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    
66. 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    
67. 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    
68. };
    
69. unsigned char shuzu8X8[]=
    
70. {
    
71. 0XBD,0X85,0X85,0XBD,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,
    
72. 0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,
    
73. 0XA1,0XA1,0XA1,0XBD,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,
    
74. 0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,0X00,
    
75. };
    
76. 
    
77. /*@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@*/
    
78. uchar xdata display[8][8];
    
79. uchar xdata msd=4;
    
80. uint ld=500;
    
81. uchar test=0,key1=0,key2=0,key3=0,key4=0;
    
82. bit pu;
    
83. uchar xsdsq=0;
    
84. uchar cd=0,cnt=0,errd_flag=0,read_flag=0,layerr=0,saom=0;
    
85. unsigned char IRCOM[7];
    
86. /*rank:A,1,2,3,4,I,心,U*/
    
87. uchar code table_cha[8][8]=
    
88. {
    
89. 0x51,0x51,0x51,0x4a,0x4a,0x4a,0x44,0x44,
    
90. 0x18,0x1c,0x18,0x18,0x18,0x18,0x18,0x3c,
    
91. 0x3c,0x66,0x66,0x30,0x18,0x0c,0x06,0x7e,
    
92. 0x3c,0x66,0x60,0x38,0x60,0x60,0x66,0x3c,
    
93. 0x30,0x38,0x3c,0x3e,0x36,0x7e,0x30,0x30,
    
94. 0x3c,0x3c,0x18,0x18,0x18,0x18,0x3c,0x3c,
    
95. 0x66,0xff,0xff,0xff,0x7e,0x3c,0x18,0x18,
    
96. 0x66,0x66,0x66,0x66,0x66,0x66,0x7e,0x3c,
    
97. };
    
98. /*the "ideasoft"*/
    
99. /*rank:A,1,2,3,4,I,心,U*////开机的LOGO显示字符字模提取PLC2002
    
100. uchar code table_cha_sj[8][8]=
     
101. {
     
102. 0x08,0x08,0x78,0x08,0x08,0x08,0x08,0xFF,/*"上",0*/
     
103. 0x18,0x04,0x22,0x24,0xFF,0x24,0x24,0x24,/*"升",0*/
     
104. 0x78,0x49,0xCE,0x00,0xFF,0x84,0x86,0xFD,/*"沿",0*/
     
105. 0x3C,0x42,0xA5,0xDB,0x81,0x99,0x42,0x3C,/*"笑脸",0*/
     
106. 0x3C,0x42,0xA5,0xDB,0x81,0x99,0x42,0x3C,/*"笑脸",0*/
     
107. 0x08,0x2A,0x2A,0xFF,0x14,0x14,0x96,0x71,/*"光",0*/
     
108. 0x08,0x7F,0x22,0x22,0x24,0x14,0x14,0xFF,/*"立",0*/
     
109. 0x08,0xFF,0x04,0x7C,0x44,0x44,0x42,0x31,/*"方",0*/
     
110. };
     
111. /*rank:3,D,C,L,U,E,F,F,T*///开机的LOGO显示字符字模提取PLC2002
     
112. uchar code table_cha_cu[9][8]=
     
113. {
     
114. 0x7E,0x40,0x40,0x7C,0x7C,0x40,0x40,0x7E,/*"3",0*/
     
115. 0x00,0x3C,0x44,0x44,0x44,0x44,0x44,0x3C,/*"D",0*/
     
116. 0x00,0x3C,0x02,0x02,0x02,0x02,0x02,0x3C,/*"C",0*/
     
117. 0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x7C,/*"L",0*/
     
118. 0x00,0x42,0x42,0x42,0x42,0x42,0x42,0x3C,/*"U",0*/
     
119. 0x00,0x7E,0x02,0x02,0x7E,0x02,0x02,0x7E,/*"E",0*/
     
120. 0x78,0x04,0x04,0x04,0x7C,0x04,0x04,0x04,/*"F",0*/
     
121. 0x78,0x04,0x04,0x04,0x7C,0x04,0x04,0x04,/*"F",0*/
     
122. 0x00,0x7E,0x18,0x18,0x18,0x18,0x18,0x18,/*"T",0*/
     
123. };
     
124. uchar code table_id[40]=
     
125. {
     
126. 0x81,0xff,0x81,0x00,0xff,0x81,0x81,0x7e,
     
127. 0x00,0xff,0x89,0x89,0x00,0xf8,0x27,0x27,
     
128. 0xf8,0x00,0x8f,0x89,0x89,0xf9,0x00,0xff,
     
129. 0x81,0x81,0xff,0x00,0xff,0x09,0x09,0x09,
     
130. 0x01,0x00,0x01,0x01,0xff,0x01,0x01,0x00,
     
131. };
     
132. /*the "ideasoft"*///侧面移动显示字符取摸plc2002
     
133. uchar code table_yd[120]={
     
134. 0x08,0x08,0x78,0x08,0x08,0x08,0x08,0xFF,/*"上",0*/
     
135. 0x18,0x04,0x22,0x24,0xFF,0x24,0x24,0x24,/*"升",0*/
     
136. 0x78,0x49,0xCE,0x00,0xFF,0x84,0x86,0xFD,/*"沿",0*/
     
137. 0x7E,0x2A,0x2A,0xFF,0xAA,0xAA,0xBE,0x40,/*"电",0*/
     
138. 0x09,0x49,0x89,0xFD,0x0B,0x0B,0x09,0x08,/*"子",0*/
     
139. 0x00,0x7C,0x92,0x92,0x92,0x92,0x7C,0x00,/*"8",0*/
     
140. 0x00,0x42,0x24,0x18,0x18,0x24,0x42,0x00,/*"x",0*/
     
141. 0x00,0x7C,0x92,0x92,0x92,0x92,0x7C,0x00,/*"8",0*/
     
142. 0x00,0x42,0x24,0x18,0x18,0x24,0x42,0x00,/*"x",0*/
     
143. 0x00,0x7C,0x92,0x92,0x92,0x92,0x7C,0x00,/*"8",0*/
     
144. 0x88,0x4E,0x78,0x0F,0xF8,0x8E,0x88,0x48,/*"光",0*/
     
145. 0x82,0x8E,0xF2,0x83,0xE2,0x9E,0x82,0x80,/*"立",0*/
     
146. 0x82,0x42,0x3E,0x0B,0x8A,0x8A,0x7A,0x02,/*"方",0*/
     
147. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
148. };
     
149. /*railway*/
     
150. uchar code dat[128]=
     
151. {
     
152. 0x00,0x20,0x40,0x60,0x80,0xa0,0xc0,0xe0,
     
153. 0xe4,0xe8,0xec,0xf0,0xf4,0xf8,0xfc,0xdc,
     
154. 0xbc,0x9c,0x7c,0x5c,0x3c,0x1c,0x18,0x14,
     
155. 0x10,0x0c,0x08,0x04,0x25,0x45,0x65,0x85,
     
156. 0xa5,0xc5,0xc9,0xcd,0xd1,0xd5,0xd9,0xb9,
     
157. 0x99,0x79,0x59,0x39,0x35,0x31,0x2d,0x29,
     
158. 0x4a,0x6a,0x8a,0xaa,0xae,0xb2,0xb6,0x96,
     
159. 0x76,0x56,0x52,0x4e,0x6f,0x8f,0x93,0x73,
     
160. 0x6f,0x8f,0x93,0x73,0x4a,0x6a,0x8a,0xaa,
     
161. 0xae,0xb2,0xb6,0x96,0x76,0x56,0x52,0x4e,
     
162. 0x25,0x45,0x65,0x85,0xa5,0xc5,0xc9,0xcd,
     
163. 0xd1,0xd5,0xd9,0xb9,0x99,0x79,0x59,0x39,
     
164. 0x35,0x31,0x2d,0x29,0x00,0x20,0x40,0x60,
     
165. 0x80,0xa0,0xc0,0xe0,0xe4,0xe8,0xec,0xf0,
     
166. 0xf4,0xf8,0xfc,0xdc,0xbc,0x9c,0x7c,0x5c,
     
167. 0x3c,0x1c,0x18,0x14,0x10,0x0c,0x08,0x04,
     
168. };
     
169. /*railway 2*/
     
170. uchar code dat2[28]=
     
171. {
     
172. 0x00,0x20,0x40,0x60,0x80,0xa0,0xc0,0xe0,
     
173. 0xe4,0xe8,0xec,0xf0,0xf4,0xf8,0xfc,0xdc,
     
174. 0xbc,0x9c,0x7c,0x5c,0x3c,0x1c,0x18,0x14,
     
175. 0x10,0x0c,0x08,0x04,
     
176. };
     
177. /*railway 3*/
     
178. uchar code dat3[24]=
     
179. {
     
180. 0x00,0x01,0x02,0x03,0x04,0x05,0x06,0x16,
     
181. 0x26,0x36,0x46,0x56,0x66,0x65,0x64,0x63,
     
182. 0x62,0x61,0x60,0x50,0x40,0x30,0x20,0x10,
     
183. };
     
184. /*3p char*/
     
185. uchar code table_3p[3][8]=
     
186. {
     
187. 0xff,0x89,0xf5,0x93,0x93,0xf5,0x89,0xff,
     
188. 0x0e,0x1f,0x3f,0x7e,0x7e,0x3f,0x1f,0x0e,
     
189. 0x18,0x3c,0x7e,0xff,0x18,0x18,0x18,0x18,
     
190. };
     
191. /*3p char*///飘雪打字显示字符取摸plc2002
     
192. uchar code table_3p_zf[11][8]={
     
193. 0x88,0x4E,0x78,0x0F,0xF8,0x8E,0x88,0x48,/*"光",0*/
     
194. 0x82,0x8E,0xF2,0x83,0xE2,0x9E,0x82,0x80,/*"立",0*/
     
195. 0x82,0x42,0x3E,0x0B,0x8A,0x8A,0x7A,0x02,/*"方",0*/
     
196. 0x00,0x7C,0x92,0x92,0x92,0x92,0x7C,0x00,/*"8",0*/
     
197. 0x00,0x42,0x24,0x18,0x18,0x24,0x42,0x00,/*"x",0*/
     
198. 0x00,0x7C,0x92,0x92,0x92,0x92,0x7C,0x00,/*"8",0*/
     
199. 0x00,0x42,0x24,0x18,0x18,0x24,0x42,0x00,/*"x",0*/
     
200. 0x00,0x7C,0x92,0x92,0x92,0x92,0x7C,0x00,/*"8",0*/
     
201. 0x00,0x00,0xC3,0xFF,0xFF,0xC3,0x00,0x00,//i
     
202. 0x0e,0x1f,0x3f,0x7e,0x7e,0x3f,0x1f,0x0e,
     
203. 0x00,0x7F,0xFF,0x80,0x80,0xFF,0x7F,0x00,//u
     
204. };
     
205. unsigned int voivol(unsigned int n);
     
206. void sendbyte(unsigned int num1,unsigned int num2,unsigned int num3,unsigned int num4);
     
207. void fvb();
     
208. void sendbyteck(unsigned int num1,unsigned int num2,unsigned int num3,unsigned int num4);
     
209. /*initializtion
     
210. That is to initialize the program .
     
211. It is write to set the timer in c52 mcu.
     
212. So the program can renovate the led_3d_cube in fixed time use the interrupt function.*/
     
213. /*##########################################################################################*/
     
214. uchar code number[]={//数字,滚动字幕使用,从上至下
     
215.         0x00,0x40,0x40,0x40,0x40,0x40,0x7E,0x00,/*"L",0*/
     
216.         0x00,0x7E,0x40,0x7E,0x40,0x40,0x7E,0x00,/*"E",1*/
     
217.         0x00,0x7C,0x46,0x42,0x42,0x46,0x7C,0x00,/*"D",2*/
     
218.         0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*" ",3*/
     
219.         0x00,0x3C,0x62,0x40,0x40,0x61,0x3E,0x00,/*"C",4*/
     
220.         0x00,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,/*"U",5*/
     
221.         0x00,0x7C,0x42,0x7C,0x42,0x41,0x7E,0x00,/*"B",6*/
     
222.         0x00,0x7E,0x40,0x7E,0x40,0x40,0x7E,0x00,/*"E",7*/
     
223.         0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*" ",8*/
     
224.         0x00,0x42,0x42,0x7E,0x42,0x42,0x42,0x00,/*"H",9*/
     
225.         0x00,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,/*"U",10*/
     
226.         0x00,0xC2,0x64,0x38,0x10,0x10,0x10,0x00,/*"Y",11*/
     
227.         0x00,0x18,0x18,0x24,0x7E,0x42,0x81,0x00,/*"A",12*/
     
228.         0x00,0x62,0x62,0x52,0x4A,0x46,0x46,0x00,/*"N",13*/
     
229.         0x00,0x3C,0x62,0x40,0x4E,0x62,0x3E,0x00,/*"G",14*/
     
230.         0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*" ",15*/
     
231.         0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*" ",16*/
     
232.         0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*" ",17*/
     
233.         0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*"Y",18*/
     
234.         0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*" ",19*/
     
235.         0x00,0x44,0x44,0x7C,0x44,0x44,0x44,0x00,/*"H",20*/
     
236.         0x00,0x44,0x44,0x44,0x44,0x44,0x38,0x00,/*"U",21*/
     
237.         0x00,0x82,0x44,0x28,0x10,0x10,0x10,0x00,/*"Y",22*/

复制代码

上图资料下载: 888光立方资料.7z (8.05 MB, 下载次数: 24)

2022-4-26 05:29 上传

点击文件名下载附件
下载积分: 黑币 -5

---

欢迎光临 (http://www.51hei.com/bbs/)

Powered by Discuz! X3.1