C语言函数声明报错error C141: syntax error near '*', expected ')' -

标题: C语言函数声明报错error C141: syntax error near '*', expected ')' [打印本页]

作者: 菲子叭叭 时间: 2024-2-29 19:08
标题: C语言函数声明报错error C141: syntax error near '*', expected ')'
#ifndef __W25Q32_H_
#define __W25Q32_H_

#include "main.h"

#define PAGESIZE    256//一页最多输入256字节

//SPI IO控制
#define SPI_SCL_1(_HANDLE_)             ( GPIO_WritePin((_HANDLE_)->uSCL_Port, (_HANDLE_)->uSCL_Pin, 1))
#define SPI_SCL_0(_HANDLE_)             ( GPIO_WritePin((_HANDLE_)->uSCL_Port, (_HANDLE_)->uSCL_Pin, 0))

#define SPI_MOSI_1(_HANDLE_)       ( GPIO_WritePin((_HANDLE_)->uMOSI_Port, (_HANDLE_)->uMOSI_Pin, 1))
#define SPI_MOSI_0(_HANDLE_)       ( GPIO_WritePin((_HANDLE_)->uMOSI_Port, (_HANDLE_)->uMOSI_Pin, 0))

#define SPI_MISO_1(_HANDLE_)       ( GPIO_WritePin((_HANDLE_)->uMISO_Port, (_HANDLE_)->uMISO_Pin, 1))
#define SPI_MISO_0(_HANDLE_)       ( GPIO_WritePin((_HANDLE_)->uMISO_Port, (_HANDLE_)->uMISO_Pin, 0))

#define SPI_CS_1(_HANDLE_)             ( GPIO_WritePin((_HANDLE_)->uCS_Port, (_HANDLE_)->uCS_Pin, 1))
#define SPI_CS_0(_HANDLE_)             ( GPIO_WritePin((_HANDLE_)->uCS_Port, (_HANDLE_)->uCS_Pin, 0))

#define SPI_MISO_R(_HANDLE_)       ( GPIO_ReadPin((_HANDLE_)->uMISO_Port, (_HANDLE_)->uMISO_Pin))

extern void  vW25Q32_Init(SPI_ObjectTypedef * hSPIx,
                                                                     uint8_t          uSCL_Port,
                                                                     uint8_t          uSCL_Pin ,

               uint8_t          uMOSI_Port,
               uint8_t          uMOSI_Pin ,

               uint8_t          uMISO_Port,
               uint8_t          uMISO_Pin ,

                                                                     uint8_t          uCS_Port,
               uint8_t          uCS_Pin);

//获取Flash ID
extern uint32_t W25Q32_Read_ID(SPI_ObjectTypedef * hSPIx);
//写使能（启动）
extern void W25Q32_Write_Enable(SPI_ObjectTypedef * hSPIx);
//等待保护(等待擦除或写入操作，直到操作完成结束)
extern void W25Q32_Wait_End(SPI_ObjectTypedef * hSPIx);
//读操作，*buf为内容，addr为地址，pagesize为要读出的字节数
extern void W25Q32_Read_Page(SPI_ObjectTypedef * hSPIx, uint8_t *buf,uint32_t addr,uint8_t pagesize);
//芯片擦除，非易失存储器，写数据前应该擦除操作
extern void W25Q32_Delete(SPI_ObjectTypedef * hSPIx);
//页写操作,*buf为内容，addr为地址，pagesize为写入字节数必须小于256个
extern void W25Q32_Write_Page(SPI_ObjectTypedef * hSPIx,uint8_t *buf, uint32_t addr,uint8_t pagesize);

#endif

Core\W25Q32.h(25): error C141: syntax error near '*', expected ')'
Core\W25Q32.h(39): error C141: syntax error near '*', expected ')'
Core\W25Q32.h(41): error C141: syntax error near '*', expected ')'
Core\W25Q32.h(43): error C141: syntax error near '*', expected ')'
Core\W25Q32.h(45): error C141: syntax error near '*', expected ')'
Core\W25Q32.h(47): error C141: syntax error near '*', expected ')'
Core\W25Q32.h(49): error C141: syntax error near '*', expected ')'

想问一下，为什么每个声明语句都有报错

作者: lkc8210 时间: 2024-2-29 20:59
要加分行符

extern void vW25Q32_Init(SPI_ObjectTypedef * hSPIx, \
uint8_t uSCL_Port, \
uint8_t uSCL_Pin, \
uint8_t uMOSI_Port, \
uint8_t uMOSI_Pin, \
uint8_t uMISO_Port, \
uint8_t uMISO_Pin, \
uint8_t uCS_Port, \
uint8_t uCS_Pin);

复制代码

作者: Hephaestus 时间: 2024-3-1 16:54
这种#define不太好，inline更好一些。比如：
#define SPI_SCL_1(_HANDLE_) ( GPIO_WritePin((_HANDLE_)->uSCL_Port, (_HANDLE_)->uSCL_Pin, 1))
我会写成：
inline void SPI_SCL_1(_HANDLE_) { GPIO_WritePin((_HANDLE_)->uSCL_Port, (_HANDLE_)->uSCL_Pin, 1))}

不过虽然编译器都支持inline，但是这并不是c语言标准关键字，要查编译器手册才可以。

欢迎光临 (http://www.51hei.com/bbs/)