关于Proteus8软件的仿真 - - Powered by Discuz!

标题: 关于Proteus8软件的仿真 [打印本页]

作者: 86873421 时间: 2025-2-28 19:31
标题: 关于Proteus8软件的仿真

出现这种情况一般是什么问题，各位大神，程序如下：

#include <reg52.h>

#include <intrins.h>

#include"24C0x.h"

#include"LCD12864.h"

#define uchar unsigned char

#define uint unsigned int

#define buffer1ID 0x01

#define buffer2ID 0x02

#define queren 0x88

#define tuichu 0x18

#define shanchu 0x82

#define User 1

void fan();

sbit B0=B^0;

sbit B7=B^7;

sbit k2=P3^7;

sbit jidianqi=P3^6;

sbit BUZZ=P2^0;

bit succeed_mm=0;

bit count_down=0;

bit alarm=0;

uchar dz[4];

uchar time[4];

uchar mima[6];

uchar mima_kai[6];

uchar mimag[6];

uchar mimaID[6]={1,2,3,4,5,6};

uchar out_time=0;

uchar Address1=20,tempx=20;

uchar Address2=20;

uchar data K;

uchar data Key;

uint PageID;

uchar data querenma=11;

uchar sum[2];

int summaf,summas;

Uchar

xdata UserPassword[2][7]={0};//密码0是管理员密码，1是开锁密码

uchar xdata DSY_BUFFER[16] ={0};//缓存

void Red_Init(void);

unsigned char check(void);

unsigned char redchange(unsigned char rednum);

void delayms(unsigned int z)

{

unsigned int x,y;

for(x=z;x>0;x--)

for(y=110;y>0;y--);

}

uchar Chack(uchar User_Number)

{

uchar flag, i,temp[6],Address;

Address=User_Number*6;

for(i=0;i<6;i++)

{

temp=x24c02_read(Address);

delayms(10);

Address++;

}

for(i=0;i<6;i++)

{

if(temp==UserPassword[User_Number])

flag=1;

else

{

flag=0;

break;

}

return flag;

}

void delay(uint tt)

{ uchar i;

while(tt--)

{

for(i=0;i<125;i++);

}

{

SCON= 0x50;//串口方式1//REN=1，允许接受

PCON=0x00;//SMOD=0

TMOD= 0x21;//定时器1定时方式2

TH1= 0xFD;//11.0592MHz模块默认波特率为9600bps

TL1= 0xFD;

TR1= 1;//启动定时器

TH0=0x4b;

TL0=0xff;

ET0=1;

TR0=1;

EA=1;

}

unsigned char Keycan(void)//按键扫描程序

{

unsigned char rcode, ccode;

P1 = 0xF0;//发送0行扫描码，列线输入

if((P1&0xF0) != 0xF0)//若有键按下

{

delay(1);//延时去抖动

if((P1&0xF0) != 0xF0)

{ rcode = 0xFE;//逐行扫描初值

while((rcode&0x10) != 0)

{

P1 = rcode;//输出行扫描码

if((P1&0xF0) != 0xF0)//本行有键按下

{

ccode = (P1&0xF0)|0x0F;

BUZZ=0;

delayms(20);

BUZZ=1;

//do{;}

while((P1&0xF0) != 0xF0); //等待键释放

return ((~rcode) + (~ccode)); //返回键编码

}

else

rcode = (rcode<<1)|0x01; //行扫描码左移一位

}

return 0; //无键按下，返回值为零

}

void KeyDeal(unsigned char Key)

{ //unsigned char n;

if(Key!=0)

{

switch(Key)

{

case 0x11: K=1; break;

case 0x21: K=2; break;

case 0x41: K=3; break;

case 0x81: break;

case 0x12: K=4; break;

case 0x22: K=5; break;

case 0x42: K=6; break;

case 0x82: K=34;break;删除

case 0x14: K=7; break;

case 0x24: K=8; break;

case 0x44: K=9; break;

case 0x84: break;输入开锁密码

case 0x18: K=35; break;退出

case 0x28: K=0; break;

case 0x48: K=11; break;

case 0x88: break;

default: break;

}

void SFG_GetEcho()//握手

{

uchar i;

SBUF=0xef;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

SBUF=0X03;

while(TI==0);

TI=0;

SBUF=0X53;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

summaf=0x57;

SBUF=summaf;

while(TI==0);

TI=0;

for(i=0;i<9;i++)

{

while(RI==0);

RI=0;}

while(RI==0);

RI=0;

querenma=SBUF;

while(RI==0);

RI=0;

sum[1]=SBUF;

while(RI==0);

RI=0;

sum[0]=SBUF;

summas=(sum[1]<<8)+sum[0];

}

void SFG_getimage()//录入指纹图像

{

uchar i;

SBUF=0xef;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

SBUF=0X03;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

summaf=0x05;

SBUF=summaf;

while(TI==0);

TI=0;

for(i=0;i<9;i++)

{

while(RI==0);

RI=0;}

while(RI==0);

RI=0;

querenma=SBUF;

while(RI==0);

RI=0;

sum[1]=SBUF;

while(RI==0);

RI=0;

sum[0]=SBUF;

summas=(sum[1]<<8)+sum[0];

}

void SFG_genchar(uchar bufferID) //生成特征并存于charbufferl//调用后单片机波特率发生变化

{

uchar i;

SBUF=0xef;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

SBUF=0X04;

while(TI==0);

TI=0;

SBUF=0X02;

while(TI==0);

TI=0;

SBUF=bufferID;

while(TI==0);

TI=0;

summaf=0x07+bufferID;

sum[0]=summaf;

sum[1]=summaf>>8;

SBUF=sum[1];

while(TI==0)

TI=0;

SBUF=sum[0];

while(TI==0)

TI=0；

for(i=0;i<9;i++)

{

while(RI==0);

RI=0;}

while(RI==0);

RI=0;

querenma=SBUF;

while(RI==0);

RI=0;

sum[1]=SBUF;

while(RI==0);

RI=0;

sum[0]=SBUF;

summas=(sum[1]<<8)+sum[0];

}

void SFG_fastsearch(uchar bufferID)//搜索指纹返回指纹ID

{

uchar i,ID1,ID2;

SBUF=0xef;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

SBUF=0X08;

while(TI==0);

TI=0;

SBUF=0X1b;

while(TI==0);

TI=0;

SBUF=bufferID;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

SBUF=0;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

SBUF=180;

while(TI==0);

TI=0;

summaf=9+0x1b+bufferID+180;

sum[0]=summaf;

sum[1]=summaf>>8;

SBUF=sum[1];

while(TI==0);

TI=0;

SBUF=sum[0];

while(TI==0);

TI=0;

for(i=0;i<9;i++)

{

while(RI==0);

RI=0;}

while(RI==0);

RI=0;

querenma=SBUF;

while(RI==0);

RI=0;

ID1=SBUF;

while(RI==0);

RI=0;

ID2=SBUF; //接收到的ID号

while(RI==0);

RI=0;

while(RI==0);

RI=0;

while(RI==0);

RI=0;

sum[1]=SBUF;

while(RI==0);

RI=0;

sum[0]=SBUF;

summas=(sum[1]<<8)+sum[0];

//PageID=ID1;

PageID=(ID1<<8)+ID2;

}

Void SFG_enroll()//自动注册模板返回存储ID=录图像+合并生成模板+储存模板

{

uchar i,ID1,ID2;

SBUF=0xef;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

SBUF=0X03;

while(TI==0);

TI=0;

SBUF=0X10;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

summaf=0x14;

SBUF=summaf; //校验和

while(TI==0);

TI=0;

for(i=0;i<9;i++)

{

while(RI==0);

RI=0;}

while(RI==0);

RI=0;

querenma=SBUF;

while(RI==0);

RI=0;

ID1=SBUF;

while(RI==0);

RI=0;

ID2=SBUF;

while(RI==0);

RI=0;

sum[1]=SBUF;

while(RI==0);

RI=0;

sum[0]=SBUF;

summas=(sum[1]<<8)+sum[0];

//PageID=ID1;

PageID=(ID1<<8)+ID2;

}

void SFG_deletchar(uint pageID) //删除指纹校验和在2字节的页码处应分高低字节相加

{

uchar i,ID1,ID2;

SBUF=0xef;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

SBUF=0X07;

while(TI==0);

TI=0;

SBUF=0X0c;

while(TI==0);

TI=0;

ID1=pageID;ID2=pageID>>8;

SBUF=ID2;

while(TI==0);

TI=0;

SBUF=ID1;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

SBUF=1;

while(TI==0);

TI=0;

summaf=0x15+ID1+ID2;

sum[0]=summaf;

sum[1]=summaf>>8;

SBUF=sum[1];

while(TI==0);

TI=0;

SBUF=sum[0];

while(TI==0);

TI=0;

for(i=0;i<9;i++)

{

while(RI==0);

RI=0;}

while(RI==0);

RI=0;

querenma=SBUF;

while(RI==0);

RI=0;

sum[1]=SBUF;

while(RI==0);

RI=0;

sum[0]=SBUF;

summas=(sum[1]<<8)+sum[0];

}

void SFG_identify() //自动验证指纹录图像+生成特征+搜索

{

uchar i,ID1,ID2;

SBUF=0xef;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0XFF;

while(TI==0);

TI=0;

SBUF=0X01;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

SBUF=0X03;

while(TI==0);

TI=0;

SBUF=0X11;

while(TI==0);

TI=0;

SBUF=0X00;

while(TI==0);

TI=0;

summaf=0x15;

SBUF=summaf; //校验和

while(TI==0);

TI=0;

for(i=0;i<9;i++)

{

while(RI==0);

RI=0;}

while(RI==0);

RI=0;

querenma=SBUF;

while(RI==0);

RI=0;

ID1=SBUF;

while(RI==0);

RI=0;

ID2=SBUF;

while(RI==0);

RI=0;

while(RI==0);

RI=0; //得分

while(RI==0);

RI=0;

sum[1]=SBUF;

while(RI==0);

RI=0;

sum[0]=SBUF;

summas=(sum[1]<<8)+sum[0];

//PageID=ID1;

PageID=(ID1<<8)+ID2;

}

void shuazhiwen()

{

uchar IDs1,IDs2,IDs3;

LcmClearTXT();

PutStr(1,1,"请按手指开锁");

SFG_identify();

count_down=1;

while(querenma==2)

{

SFG_identify();

if(out_time>=10)

{

out_time=0;

count_down=0;

succeed_mm=0;

goto out_fingerprint;

}

if(querenma==0)

{

out_time=0;

count_down=0;

ERROR_TIME=0;

BUZZ=1;

alarm=0;

LcmClearTXT();

PutStr(1,2,"门已打开");

IDs1=PageID/100;

IDs2=PageID/10%10;

IDs3=PageID%10;

PutStr(2,1,"编号为：");

WriteCommand(0x8D);//指定第三行显示位置

WriteData(0x30+IDs1);

WriteData(0x30+IDs2);

WriteData(0x30+IDs3);

jidianqi=0;

delay(5000);

jidianqi=1;

succeed_mm=0;

}

else if(querenma==9)

{

LcmClearTXT();

ERROR_TIME++;

if(ERROR_TIME>=3)

{

alarm=1;

}

PutStr(1,1,"没搜索到指纹");

PutStr(2,1,"请重新按手指");

out_time=0;

count_down=0;

}

else

{

LcmClearTXT();

PutStr(1,1,"接受包出错");

out_time=0;

count_down=0;

}

delay(2000);

out_fingerprint:

LcmClearTXT();

void addfinger()

{

uchar IDa1,IDa2,IDa3;

LcmClearTXT();

PutStr(1,2,"请按手指");

SFG_getimage();

while(querenma!=0)

SFG_getimage();

SFG_genchar(buffer1ID);

UART_Init();

SFG_fastsearch(buffer1ID);

while(querenma==1)

SFG_fastsearch(buffer1ID);

if(querenma==0)

{

LcmClearTXT();

PutStr(1,1,"指纹已存在");

PutStr(3,0,"按任意键继续");

while(Keycan()==0);

}

else if(querenma==9)

{

LcmClearTXT();

PutStr(1,1,"请再次按手指");

SFG_enroll();

while(querenma==2)

SFG_enroll();

LcmClearTXT();

if(querenma==0)

{

IDa1=PageID/100;IDa2=PageID/10%10;IDa3=PageID%10;

PutStr(1,1,"指纹采集成功");

PutStr(2,1,"编号为：");

WriteCommand(0x8D);

WriteData(0x30+IDa1);WriteData(0x30+IDa2);WriteData(0x30+IDa3);

}

else if(querenma!=0)

{

PutStr(1,1,"指纹采集失败");

PutStr(2,1,"请重新操作");

}

PutStr(3,0,"按任意键继续");

while(Keycan()==0);

}

LcmClearTXT();

}

Void deletfinger()

{

uchar i,j=0;

LcmClearTXT();

PutStr(1,0,"输入删去的指纹号");

PutStr(3,0,"B退格 D确认");

for(i=0;i<5;i++)dz=0;

Key=Keycan();

while(Key!=queren)

{

Key=Keycan();

KeyDeal(Key);

if(K==35) goto out2;

delay(30); //按键有抖动

if(Key==0)K=10;

if((K>=0)&&(K<=9))

{

dz[j]=K;

if(j<3)

{

WriteCommand(0x88+j); //指定第三行显示位置

WriteData(0x30+dz[j]);

}

++j;

if(j==4)

j=3;

} //显示LCD12864并行显示

if(K==34) //按了删除键

{

if(j==0)

{

WriteCommand(0x88);//指定第三行显示位置

WriteData(0x20);

}

else

{

--j;

WriteCommand(0x88+j); //指定第三行显示位置

WriteData(0x20);

}

if(j>=2)

PageID=dz[2]+dz[1]*10+dz[0]*100;

if(j==1)

PageID=dz[1]+dz[0]*10;

if(j==0)

PageID=dz[0];

SFG_deletchar(PageID);

if(querenma==0)

{

LcmClearTXT();

PutStr(1,1,"删去指纹号成功");

}

else

{

LcmClearTXT();

PutStr(1,2,"删去指纹号失败");

}

PutStr(2,0,"按任意键继续");

while(Keycan()==0);

out2:

LcmClearTXT();

K=0;

}

void gaimima()

{

uchar i,j=0,mima1[6],mima2[6];

uchar k,temp;

resum_modification:

LcmClearTXT();

PutStr(1,1,"请输入新密码");

PutStr(3,0,"B退格 D确认");

for(i=0;i<6;i++)mima1=0;

Key=Keycan();

while(Key!=queren)

{

Key=Keycan();

KeyDeal(Key);

if(K==35) goto out3;

delay(30);

if(Key==0)K=10;

if((K>=0)&&(K<=9))

{

mima1[j]=K;

if(j<6)

{

WriteCommand(0x89+j); //指定第三行显示

WriteData(0x0f);

}

++j;

if(j==7)

j=6;

}//显示LCD12864并行显示

if(K==34) //按了删除键

{

if(j==0)

{

WriteCommand(0x89); //指定第三行显示

WriteData(0x20);

}

else

{

--j;

WriteCommand(0x89+j); //指定第三行显示

WriteData(0x20);

}

LcmClearTXT();

j=0;

PutStr(1,0,"请再次输入新密码");

PutStr(3,0,"B退格 D确认");

for(i=0;i<6;i++)mima2=0;

Key=Keycan();

while(Key!=queren)

{

Key=Keycan();

KeyDeal(Key);

delay(30);

if(Key==0)K=10;

if((K>=0)&&(K<=9))

{

mima2[j]=K;

if(j<6)

{

WriteCommand(0x89+j);//指定第三行显示

WriteData(0x0f);

}

++j;

if(j==7)

j=6;

}//显示LCD12864并行显示

if(K==34) //按了删除键

{

if(j==0)

{

WriteCommand(0x89);//指定第三行显示

WriteData(0x20);

}

else

{

--j;

WriteCommand(0x89+j);//指定第三行显示

WriteData(0x20);

}

LcmClearTXT();

if((mima1[0]==mima2[0])&&(mima1[1]==mima2[1])&&(mima1[2]==mima2[2])&&(mima1[3]==mima2[3])&&(mima1[4]==mima2[4])&&(mima1[5]==mima2[5]))

{

for(i=0;i<6;i++)

mimaID=mima1;

for(i=0;i<6;i++)//密码限制在六位以内

{

UserPassword[0]=mima1;

}

temp=(Member-1)*6;

delayms(5);

for(k=0;k<6;k++)

{

x24c02_write(temp,UserPassword[0][k]);

delayms(10);

temp++;

}

PutStr(0,1,"密码修改成功");

PutStr(3,0,"按任意键继续");

while(Keycan()==0);

}

else

{

j=0;

PutStr(0,0,"密码修改失败");

PutStr(1,0,"两次输入的密码不");

PutStr(2,0,"一致，请重新操作");

PutStr(3,0,"按任意键继续");

while(Keycan()==0);

goto resum_modification;

}

out3:

LcmClearTXT();

K=0;

}

void gaimima_kaisuo()

{

uchar i,j=0,mima1[6],mima2[6];

uchar k,temp;

resum_modification1:

LcmClearTXT();

PutStr(1,1,"请输入新密码");

PutStr(3,0,"B退格 D确认");

for(i=0;i<6;i++)mima1=0;

Key=Keycan();

while(Key!=queren)

{

Key=Keycan();

KeyDeal(Key);

if(K==35) goto out4;

delay(30);

if(Key==0)K=10;

if((K>=0)&&(K<=9))

{

mima1[j]=K;

if(j<6)

{

WriteCommand(0x89+j); //指定第三行显示

WriteData(0x0f);

}

++j;

if(j==7)

j=6;

}//显示LCD12864并行显示

if(K==34)//按了删除键

{

if(j==0)

{

WriteCommand(0x89); //指定第三行显示

WriteData(0x20);

}

else

{

--j;

WriteCommand(0x89+j); //指定第三行显示

WriteData(0x20);

}

LcmClearTXT();

j=0;

PutStr(1,0,"请再次输入新密码");

PutStr(3,0,"B退格 D确认");

for(i=0;i<6;i++)mima2=0;

Key=Keycan();

while(Key!=queren)

{

Key=Keycan();

KeyDeal(Key);

delay(30);

if(Key==0)K=10;

if((K>=0)&&(K<=9))

{

mima2[j]=K;

if(j<6)

{

WriteCommand(0x89+j);//指定第三行显示

WriteData(0x0f);

}

++j;

if(j==7)

j=6;

} //显示LCD并行显示

if(K==34) //按了删除键

{

if(j==0)

{

WriteCommand(0x89);//指定第三行显示

WriteData(0x20);

}

else

{

--j;

WriteCommand(0x89+j); //指定第三行显示

WriteData(0x20);

}

LcmClearTXT();

if((mima1[0]==mima2[0])&&(mima1[1]==mima2[1])&&(mima1[2]==mima2[2])&&(mima1[3]==mima2[3])&&(mima1[4]==mima2[4])&&(mima1[5]==mima2[5]))

{

for(i=0;i<6;i++)

mimaID=mima1;

for(i=0;i<6;i++)/密码限制在6位以内

{

UserPassword[1]=mima1;

}

temp=(Member-1)*6;

delayms(5);

for(k=0;k<6;k++)

{

x24c02_write(temp,UserPassword[1][k]);

delayms(10);

temp++;

}

PutStr(0,1,"密码修改成功");

PutStr(3,0,"按任意键继续");

while(Keycan()==0);

}

else

{

j=0;

PutStr(0,0,"密码修改失败");

PutStr(1,0,"两次输入的密码不");

PutStr(2,0,"一致，请重新操作");

PutStr(3,0,"按任意键继续");

while(Keycan()==0);

goto resum_modification1;

}

out4:

LcmClearTXT();

K=0;

}

void zhu()

{

LcmClearTXT();

PutStr(1,2,"门已打开");

jidianqi=0;

delay(5000);

jidianqi=1;

//PutStr(3,0,"按任意键继续");

//while(Keycan()==0);

K=35;

}

void xiugaimima()

{

LcmClearTXT();

while(Keycan()!=tuichu)

{

PutStr(0,0,"按1：修改开锁密码");

PutStr(1,0,"按2：修改管理密码");

KeyDeal(Keycan());

if(K==35) goto out5;

switch(K)

{

case 1: Member=2;gaimima_kaisuo();break;

case 2: Member=1;gaimima();break;

default: break;

}

out5:

LcmClearTXT();

K=0;

}

void guanliyuan()

{ uchar i,j=0,x=1;

uchar Right_flag;

resum_guanliyuan:

LcmClearTXT();

PutStr(1,0,"请输入管理密码");

PutStr(3,0,"B退格 D确认");

for(i=0;i<6;i++)mima=0;

Key=Keycan();

while(Key!=queren)

{

Key=Keycan();

if(Key==tuichu) goto out1;

KeyDeal(Key);

delay(30);

if(Key==0)K=10;

if((K>=0)&&(K<=9))

{

mima[j]=K;

if(j<6)

{

WriteCommand(0x89+j);//指定第三行显示

WriteData(0x0f);

}

++j;

if(j==7)

j=6;

} //显示LCD12864并行显示

if(K==34)//按了删除键

{

if(j==0)

{

WriteCommand(0x89);//指定第三行显示

WriteData(0x20);

}

else

{

--j;

WriteCommand(0x89+j); //指定第三行显示

WriteData(0x20);

}

LcmClearTXT();

for(i=0;i<6;i++)

{

UserPassword[0]=mima;

}

if(j==6){Right_flag=Chack(0); }

if (Right_flag==1)

{

Right_flag=0;

ERROR_TIME=0;

alarm=0;

BUZZ=1;

while(Keycan()!=tuichu)

{

PutStr(0,0,"按1：增加指纹");

PutStr(1,0,"按2：删除指纹");

PutStr(2,0,"按3：修改密码");

PutStr(3,0,"按4：手动开锁");

KeyDeal(Keycan());

if(K==35) goto out1;

switch(K)

{

case 1: addfinger();K=6;break;

case 2:deletfinger();break;

case 3: xiugaimima();break;

case 4:zhu();break;

default: break;

}

else

{

j=0;

ERROR_TIME++;

if(ERROR_TIME>=3)

{

alarm=1;

}

PutStr(1,2,密码错误");

PutStr(2,0,"请重新操作");

PutStr(3,0,"按任意键继续");

while(Keycan()==0);

goto resum_guanliyuan;

}

Key=0;

out1:

LcmClearTXT();

}

void kaisuomm()

{ uchar i,j=0,x=1;

uchar Right_flag;

resume: PutStr(1,0,"请输入开锁面膜");

PutStr(3,0,"B退格 D确认");

for(i=0;i<6;i++)mima_kai=0;

Key=Keycan();

while(Key!=queren)

{

Key=Keycan();

if(Key==tuichu) goto out;

KeyDeal(Key);

delay(30);

if(Key==0)K=10;

if((K>=0)&&(K<=9))

{

mima_kai[j]=K;

if(j<6)

{

WriteCommand(0x89+j);//指定第三行显示

WriteData(0x0f);

}

++j;

if(j==7)

j=6;

} //显示LCD12864并行显示

if(K==34)//按了删除键

{

if(j==0)

{

WriteCommand(0x89);//指定第三行显示

WriteData(0x20);

}

else

{

--j;

WriteCommand(0x89+j);//指定第三行显示

WriteData(0x20);

}

for(i=0;i<6;i++)

{

UserPassword[1]=mima_kai;

}

if(j==6){Right_flag=Chack(1); }

if (Right_flag==1)

{

Right_flag=0;

succeed_mm=1;

ERROR_TIME=0;

BUZZ=1;

alarm=0;

//while(Keycan()!=tuichu)

{

PutStr(1,0,"请刷手指开锁");

PutStr(3,0);

}

else

{

j=0;

ERROR_TIME++;

if(ERROR_TIME>=3)

{

alarm=1;

}

//PutStr(1,0);

PutStr(1,0,"密码错误");

PutStr(2,0,"请重新输入");

PutStr(3,0,"按任意键继续");

while(Keycan()==0);

LcmClearTXT();

goto resume;

}

Key=0;

out:

LcmClearTXT();

}

void fan()

{

if(succeed_mm==0)

{

PutStr(0,2,"欢迎使用");

PutStr(1,1,"指纹识别系统");

PutStr(2,0," ");

PutStr(3,0,"A管理 C开锁");

}

Key=Keycan();

if(Key==0x84)

{

LcmClearTXT();

kaisuomm();

LcmClearTXT();

// K=0;

}

if(/*k2==1&&*/succeed_mm==1)//指纹刷机

{

LcmClearTXT();

shuazhiwen();

LcmClearTXT();

}

if(Key==0x81)//管理员操作

{

LcmClearTXT();

guanliyuan();

LcmClearTXT();

}

void main()

{

//PSB=0;

UART_Init();//串口初始化

x24c02_init();//24C02初始化

LcmInit();//LCD12864初始化

LcmClearTXT();//LCD12864清屏

while(1)

{

fan();

delay(100);

}

void T0_time() interrupt 1

{

uchar jishi;

TH0=0x4b;

TL0=0xff;

jishi++;

if(jishi%2==0&&alarm==1)

{

BUZZ=!BUZZ;

}

if(jishi>=20)

{

jishi=0;

if(count_down==1)

out_time++;

}

作者: songxia8013 时间: 2025-3-1 08:51
这个没碰到过。不过WP引脚一般是接地，只用SCL和SDA这俩脚传输数据。

欢迎光临 (http://www.51hei.com/bbs/) Powered by Discuz! X3.1