标题: 51单片机+无字库12864测试程序(纵向取模。字节倒序) [打印本页]

---

作者: huxiao    时间: 2015-1-24 15:34
标题: 51单片机+无字库12864测试程序(纵向取模。字节倒序)

1. /***********************************************************************
   
2.         无字库12864测试程序(纵向取模。字节倒序)
   
3.                          crasyboye      
   
4. ***********************************************************************/
   
5. 
   
6. #include <reg51.h>
   
7. #include <ctype.h>
   
8. #include <string.h>
   
9. #include <stdlib.h>
   
10. #include <stdio.h>
    
11. #include <math.h>
    
12. 
    
13. /* Define the register command code */
    
14. #define Disp_On 0x3f
    
15. #define Disp_Off 0x3e
    
16. #define Col_Add 0x40
    
17. #define Page_Add 0xb8
    
18. #define Start_Line 0xc0
    
19. 
    
20. #define Lcd_Bus P0 //MCU P1<------> LCM
    
21. 
    
22. sbit Mcs=P2^3; //Master chip enable
    
23. sbit Scs=P2^4; //Slave chip enable
    
24. sbit Enable=P2^2; //6800 mode Enable single
    
25. sbit Di=P2^0; //Data or Instrument Select
    
26. sbit RW=P2^1; //Write or Read
    
27. sbit Lcd_Rst=P2^5; //Lcm reset
    
28. 
    
29. char code ce[]={
    
30. /*-- 文字: 测 --*/
    
31. /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
    
32. 0x08,0x31,0x86,0x60,0x00,0xFE,0x02,0xF2,0x02,0xFE,0x00,0xF8,0x00,0x00,0xFF,0x00,
    
33. 0x04,0xFC,0x03,0x00,0x80,0x47,0x30,0x0F,0x10,0x67,0x00,0x07,0x40,0x80,0x7F,0x00
    
34. };
    
35. char code shi[]={
    
36. /*-- 文字: 试 --*/
    
37. /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
    
38. 0x40,0x42,0xDC,0x08,0x00,0x90,0x90,0x90,0x90,0x90,0xFF,0x10,0x12,0x1C,0x10,0x00,
    
39. 0x00,0x00,0x7F,0x20,0x10,0x20,0x20,0x1F,0x10,0x10,0x01,0x06,0x18,0x20,0x78,0x00
    
40. };
    
41. char code kai[]={
    
42. /*-- 文字: 开 --*/
    
43. /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
    
44. 0x40,0x42,0x42,0x42,0x42,0xFE,0x42,0x42,0x42,0x42,0xFE,0x42,0x42,0x42,0x42,0x00,
    
45. 0x00,0x40,0x20,0x10,0x0C,0x03,0x00,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x00
    
46. };
    
47. char code shi3[]={
    
48. /*-- 文字: 始 --*/
    
49. /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
    
50. 0x10,0x90,0x70,0x1F,0x12,0xF0,0x00,0x20,0x70,0x28,0x27,0x22,0x28,0x70,0x20,0x00,
    
51. 0x40,0x21,0x12,0x0C,0x06,0x09,0x30,0x00,0x7F,0x21,0x21,0x21,0x21,0x7F,0x00,0x00
    
52. };
    
53. 
    
54. char code wan[]={
    
55. /*-- 文字: 完 --*/
    
56. /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
    
57. 0x00,0x90,0x8C,0xA4,0xA4,0xA4,0xA5,0xA6,0xA4,0xA4,0xA4,0xA4,0x94,0x8C,0x04,0x00,
    
58. 0x00,0x80,0x40,0x20,0x18,0x07,0x00,0x00,0x00,0x3F,0x40,0x40,0x40,0x70,0x00,0x00
    
59. };
    
60. char code bi[]={
    
61. /*-- 文字: 毕 --*/
    
62. /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
    
63. 0x00,0x00,0xFF,0x88,0x48,0x28,0x08,0x80,0x7F,0x88,0x88,0x88,0x84,0x84,0xE0,0x00,
    
64. 0x04,0x04,0x04,0x04,0x04,0x04,0x04,0xFF,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00
    
65. };
    
66. 
    
67. unsigned char code FirstPage[]={
    
68. /*-- 调入了一幅图像：C:\Documents and Settings\freelover\桌面\未标题-1.bmp --*/
    
69. /*-- 宽度x高度=128x64 --*/
    
70. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x28,0x48,0x88,0x08,0x88,0x78,0x08,0x80,0x60,
    
71. 0x3E,0xA0,0x20,0x20,0xA0,0x60,0x20,0x00,0x00,0x40,0x42,0x44,0xCC,0x00,0x00,0xF8,
    
72. 0x08,0x04,0x04,0xF8,0x08,0x08,0x08,0xFC,0x08,0x00,0x00,0x00,0x80,0x40,0xF0,0x0E,
    
73. 0x08,0xC8,0x48,0x48,0x48,0xFE,0x48,0x48,0x48,0xCC,0x08,0x00,0x00,0x00,0x00,0xFC,
    
74. 0x44,0x44,0x44,0x44,0x44,0xFC,0x44,0x44,0x44,0x44,0xFE,0x04,0x00,0x00,0x80,0x40,
    
75. 0x20,0x10,0x10,0x10,0x20,0x70,0x00,0x10,0xF0,0x10,0x10,0x10,0x10,0xE0,0x00,0x00,
    
76. 0x10,0xF0,0x10,0x10,0x10,0x10,0xE0,0x00,0x00,0x00,0xF0,0x10,0x10,0x10,0x10,0x10,
    
77. 0x10,0x00,0x00,0x00,0x20,0x20,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    
78. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x20,0x19,0x06,0x05,0x08,0xB0,0x40,0x20,
    
79. 0x18,0x07,0x18,0x20,0x40,0x80,0x80,0x00,0x00,0x80,0x40,0x20,0x1F,0x20,0x40,0x8F,
    
80. 0x84,0x84,0x82,0xFF,0x80,0x88,0x90,0x8F,0x80,0x00,0x00,0x01,0x00,0x00,0xFF,0x00,
    
81. 0x00,0x07,0x8C,0x54,0x24,0x5F,0x84,0x84,0x04,0x07,0x00,0x00,0x00,0x00,0xC0,0x3F,
    
82. 0x04,0x04,0x04,0x04,0x04,0xFF,0x04,0x04,0x84,0x04,0xFF,0x00,0x00,0x00,0x1F,0x60,
    
83. 0x80,0x80,0x80,0x80,0x40,0x30,0x00,0x80,0xFF,0x82,0x02,0x0E,0x32,0xC1,0x80,0x00,
    
84. 0x80,0xFF,0x82,0x82,0x82,0x83,0x44,0x38,0x00,0x00,0x73,0x82,0x81,0x81,0x81,0x42,
    
85. 0x3C,0x00,0x00,0x00,0x80,0x80,0xFF,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    
86. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x10,0x91,0x51,0x30,0x10,0x10,
    
87. 0x90,0x50,0x10,0x10,0x00,0x01,0x10,0x10,0xF0,0x90,0x90,0x90,0x90,0x10,0xE0,0x00,
    
88. 0x00,0xF0,0x00,0x00,0x00,0xC0,0x50,0x50,0x60,0x40,0xC0,0x40,0x60,0x50,0x51,0xC0,
    
89. 0x01,0x01,0x00,0x00,0xE0,0x00,0x00,0x00,0x01,0xF1,0x01,0x00,0x00,0x01,0x00,0x00,
    
90. 0x80,0x80,0xF0,0x80,0x80,0x01,0xE0,0x20,0x20,0xE1,0x00,0x00,0x00,0x00,0xE0,0x20,
    
91. 0x20,0xA0,0x20,0x20,0x30,0xA0,0x20,0x20,0x20,0x20,0xE0,0x00,0xD0,0x10,0x10,0xF0,
    
92. 0x00,0x00,0x80,0x40,0x30,0x40,0x80,0x00,0x00,0x00,0x80,0x80,0xF0,0x80,0x80,0xE0,
    
93. 0x20,0x20,0x20,0x10,0x10,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    
94. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x89,0x49,0x2D,0x8D,0x0B,0xF9,0x09,
    
95. 0x08,0x2A,0x4C,0x98,0x00,0x00,0x04,0x03,0x84,0x48,0x30,0x0C,0x03,0x00,0x3F,0x00,
    
96. 0x00,0xFF,0x00,0x00,0x40,0x5F,0x52,0x52,0x52,0x52,0xFF,0x52,0x52,0x52,0x52,0x5F,
    
97. 0x40,0x00,0x00,0x80,0x7F,0x09,0x09,0x09,0x09,0x09,0x09,0xF9,0x01,0x01,0x00,0x00,
    
98. 0x18,0x06,0xFF,0x04,0x08,0x80,0x7F,0x00,0x00,0xFF,0x00,0x00,0xC0,0x00,0x10,0x10,
    
99. 0x12,0x94,0x99,0x52,0x30,0x1F,0x30,0x50,0x90,0x10,0x10,0x00,0x47,0x44,0x24,0x27,
    
100. 0xFE,0x09,0x72,0x0A,0x72,0x82,0x60,0x1B,0x01,0x00,0x18,0x06,0xFF,0x04,0x88,0x7F,
     
101. 0x05,0x89,0x51,0x71,0x8D,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
102. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x08,0xF9,0x08,0x08,
     
103. 0x08,0xF8,0x08,0x08,0x00,0x00,0x01,0x01,0x30,0x28,0x20,0xE0,0x3C,0x20,0x20,0x35,
     
104. 0x29,0x20,0x20,0x00,0x00,0x40,0x40,0x50,0x50,0x50,0xFD,0xD0,0x50,0x70,0x50,0x48,
     
105. 0x40,0x00,0x01,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x81,0x80,0x80,0x80,0x00,
     
106. 0x80,0x80,0x81,0x01,0x81,0x80,0x00,0x00,0x00,0x80,0x81,0x81,0x00,0x00,0x01,0x01,
     
107. 0x81,0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x81,0x81,0x80,0x10,0xF0,0x81,0x81,
     
108. 0x80,0x01,0x01,0x01,0x01,0x81,0x81,0x81,0x01,0x00,0x80,0x80,0x81,0x01,0x80,0x81,
     
109. 0x81,0x00,0x00,0x80,0x80,0x81,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
110. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x21,0x11,0x0D,0x07,0x01,0x01,
     
111. 0x01,0x3F,0x01,0x01,0x01,0x00,0x00,0x08,0x0C,0x26,0x23,0x30,0x17,0x1D,0x19,0x17,
     
112. 0x31,0x20,0x20,0x00,0x00,0x04,0x04,0x02,0x3E,0x29,0x29,0x2A,0x2A,0x2A,0x3E,0x00,
     
113. 0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00,0x00,0x0F,0x10,0x10,0x10,0x09,0x00,
     
114. 0x10,0x10,0x1F,0x11,0x10,0x00,0x00,0x00,0x09,0x14,0x12,0x12,0x1F,0x10,0x00,0x19,
     
115. 0x12,0x12,0x14,0x09,0x00,0x40,0x41,0x66,0x18,0x06,0x01,0x00,0x00,0x1F,0x10,0x10,
     
116. 0x10,0x0F,0x00,0x00,0x0F,0x10,0x10,0x10,0x0F,0x00,0x40,0x41,0x66,0x18,0x06,0x01,
     
117. 0x00,0x00,0x0F,0x12,0x12,0x12,0x0B,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
118. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
119. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
120. 0x00,0x00,0x00,0x00,0x00,0x02,0x0E,0xF2,0x00,0xF2,0x0E,0x02,0x02,0xFE,0x22,0x22,
     
121. 0x72,0x06,0x00,0x02,0xFE,0x12,0x32,0xD2,0x0C,0x00,0x00,0x00,0x18,0x18,0x00,0x00,
     
122. 0x00,0x00,0x04,0x04,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF8,
     
123. 0x04,0x02,0x02,0x04,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
124. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
125. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
126. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
127. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
128. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x02,0x03,0x02,0x02,
     
129. 0x02,0x03,0x00,0x02,0x03,0x02,0x00,0x00,0x03,0x02,0x00,0x00,0x03,0x03,0x00,0x00,
     
130. 0x00,0x00,0x02,0x02,0x03,0x02,0x02,0x00,0x00,0x03,0x03,0x00,0x00,0x00,0x00,0x00,
     
131. 0x01,0x02,0x02,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
132. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
133. 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
     
134. };
     
135. 
     
136. /*------------------延时子程序-----------------------------*/
     
137. void delay(unsigned int t)
     
138. {
     
139. unsigned int i,j;
     
140. for(i=0;i<t;i++)
     
141. for(j=0;j<10;j++)
     
142. ;
     
143. }
     
144. 
     
145. /*------------------写命令到LCD------------------------------*/
     
146. void write_com(unsigned char cmdcode)
     
147. {
     
148. 
     
149. Di=0;
     
150. RW=0;
     
151. 
     
152. Lcd_Bus=cmdcode;
     
153. delay(0);
     
154. Enable=1;
     
155. delay(0);
     
156. Enable=0;
     
157. }
     
158. 
     
159. /*-------------------写数据到LCD----------------------------*/
     
160. 
     
161. void write_data(unsigned char Dispdata)
     
162. {
     
163. 
     
164. Di=1;
     
165. RW=0;
     
166. 
     
167. Lcd_Bus=Dispdata;
     
168. delay(0);
     
169. Enable=1;
     
170. delay(0);
     
171. Enable=0;
     
172. }
     
173. 
     
174. 
     
175. /*------------------显示边框-------------------------------*/
     
176. void frame()
     
177. {
     
178. unsigned char i;
     
179. Mcs=1;
     
180. Scs=1;
     
181. write_com(Page_Add+0);
     
182. write_com(Col_Add+0);
     
183. for(i=0;i<64;i++) write_data(0x01);
     
184. write_com(Page_Add+7);
     
185. write_com(Col_Add+0);
     
186. for(i=0;i<64;i++) write_data(0x80);
     
187. 
     
188. for(i=0;i<8;i++)
     
189. 
     
190. {
     
191. Mcs=0;
     
192. Scs=1;
     
193. write_com(Page_Add+i);
     
194. write_com(Col_Add+63);
     
195. write_data(0xff);
     
196. Mcs=1;
     
197. Scs=0;
     
198. write_com(Page_Add+i);
     
199. write_com(Col_Add+0);
     
200. write_data(0xff);
     
201. }
     
202. }
     
203. 
     
204. /*------------------清除内存---------------*/
     
205. void Clr_Scr()
     
206. {
     
207. unsigned char j,k;
     
208. Mcs=1;Scs=1;
     
209. write_com(Page_Add+0);
     
210. write_com(Col_Add+0);
     
211. 
     
212. for(k=0;k<8;k++){
     
213. write_com(Page_Add+k);
     
214. for(j=0;j<64;j++)write_data(0x00);
     
215. }
     
216. }
     
217. 
     
218. /*------------------显示12864图片---------------------------*/
     
219. void Disp_Img(unsigned char code *img)
     
220. {
     
221. unsigned char j,k;
     
222. for(k=0;k<8;k++){
     
223. Mcs=1;Scs=0;delay(10);
     
224. write_com(Page_Add+k);
     
225. write_com(Col_Add+0);
     
226. for(j=0;j<64;j++) write_data(img[k*128+j]);
     
227. Mcs=0;Scs=1; delay(10);
     
228. write_com(Page_Add+k);
     
229. write_com(Col_Add+0);
     
230. for(j=64;j<128;j++) write_data(img[k*128+j]);
     
231. }
     
232. }
     
233. 
     
234. /*------------------显示横---------------------------*/
     
235. void Disp_H_Line()
     
236. {
     
237. unsigned char i,j;
     
238. Mcs=1;
     
239. Scs=1;
     
240. write_com(Disp_On);
     
241. write_com(Page_Add);
     
242. write_com(Start_Line);
     
243. write_com(Col_Add);
     
244. 
     
245. for(j=0;j<8;j++)
     
246. {
     
247. write_com(Page_Add+j);
     
248. write_com(Col_Add+0);
     
249. // write_com(Start_Line+0);
     
250. for(i=0;i<64;i++)write_data(0x55);
     
251. }
     
252. }
     
253. 
     
254. 
     
255. /*------------------显示列-----------------------------*/
     
256. void Disp_V_Line()
     
257. {
     
258. unsigned char i,j;
     
259. write_com(Disp_On);
     
260. write_com(Page_Add);
     
261. write_com(Start_Line);
     
262. write_com(Col_Add);
     
263. 
     
264. for(j=0;j<8;j++)
     
265. {
     
266. write_com(Page_Add+j);
     
267. write_com(Col_Add+0);
     
268. write_com(Start_Line+0);
     
269. for(i=0;i<32;i++)
     
270. {
     
271. write_data(0x00);
     
272. write_data(0xff);
     
273. }
     
274. 
     
275. }
     
276. }
     
277. 
     
278. /*---------------------指定位置显示汉字16*16-----------------------*/
     
279. 
     
280. void hz_disp16(unsigned char pag,unsigned char col, unsigned char code *hzk)
     
281. {
     
282. unsigned char j=0,i=0;
     
283. for(j=0;j<2;j++){
     
284. write_com(Page_Add+pag+j);
     
285. write_com(Col_Add+col);
     
286. for(i=0;i<16;i++) write_data(hzk[16*j+i]);
     
287. }
     
288. }
     
289. 
     
290. 
     
291. /*------------------初始化LCD屏--------------------------*/
     
292. void init_lcd()
     
293. {
     
294. Lcd_Rst=0;
     
295. delay(100);
     
296. Lcd_Rst=1;
     
297. delay(100);
     
298. 
     
299. Mcs=1;
     
300. Scs=1;
     
301. 
     
302. delay(100);
     
303. write_com(Disp_Off);
     
304. write_com(Page_Add+0);
     
305. write_com(Start_Line+0);
     
306. write_com(Col_Add+0);
     
307. write_com(Disp_On);
     
308. }
     
309. 
     
310. 
     
311. /*------------------------------信息显示------------------------*/
     
312. void Msg(int flg)
     
313. {
     
314. Clr_Scr();
     
315. frame();
     
316. if(flg==0){ //显示“测试开始”
     
317. Mcs=1;Scs=0;
     
318. hz_disp16(3,32,ce);
     
319. delay(2000);
     
320. hz_disp16(3,48,shi);
     
321. delay(2000);
     
322. Mcs=0;Scs=1;
     
323. hz_disp16(3,0,kai);
     
324. delay(2000);
     
325. hz_disp16(3,16,shi3);
     
326. delay(2000);
     
327. }
     
328. else if(flg==1){ //显示“测试完毕”
     
329. Mcs=1;Scs=0;
     
330. hz_disp16(3,32,ce);
     
331. hz_disp16(3,48,shi);
     
332. Mcs=0;Scs=1;
     
333. hz_disp16(3,0,wan);
     
334. hz_disp16(3,16,bi);
     
335. }
     
336. }
     
337. 
     
338. /*--------------------主程序---------------------------------*/
     
339. 
     
340. 
     
341. main()
     
342. {
     
343. unsigned char i=0;
     
344. while(1){
     
345. 
     
346. init_lcd();
     
347. Disp_Img(FirstPage);
     
348. delay(30000);
     
349. Msg(0);
     
350. delay(10000);
     
351. Disp_H_Line();
     
352. delay(10000);
     
353. Disp_V_Line();
     
354. delay(10000);
     
355. Msg(1);
     
356. delay(10000);
     
357. }
     
358. }

复制代码

---

欢迎光临 (http://www.51hei.com/bbs/)

Powered by Discuz! X3.1