stm32 ADC单通道连续采样并用串口发送电压值程序 -

标题: stm32 ADC单通道连续采样并用串口发送电压值程序 [打印本页]

作者: geige 时间: 2015-7-26 02:12
标题: stm32 ADC单通道连续采样并用串口发送电压值程序
#include "stm32f10x.h"

void Delay(unsigned int x);//延时
void GPIO_Configuration(void);//IO口配置
void UART_Init(void); //串口初始化
void UART2_PutChar(u8 ch);  //串口发送数据
void ADC_Configuration(void);  //ADC配置
void Read_ADC_Result(void);  //ADC读取结果

int main(void)
{
SystemInit();
unsigned int t;
GPIO_Configuration();
UART_Init();
ADC_Configuration();
while(1)
{Read_ADC_Result();
for(t=0;t<100;t++)
{Delay(65530);}
}
}

void GPIO_Configuration(void)
{
GPIO_InitTypeDefGPIO_InitStructure;
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2,ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_AFIO, ENABLE);
  //GPIO_PinRemapConfig(GPIO_PartialRemap_USART3,ENABLE);
GPIO_InitStructure.GPIO_Pin =GPIO_Pin_2;
GPIO_InitStructure.GPIO_Mode =GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed= GPIO_Speed_50MHz;
GPIO_Init(GPIOA,&GPIO_InitStructure);

GPIO_InitStructure.GPIO_Pin =GPIO_Pin_3;
GPIO_InitStructure.GPIO_Mode =GPIO_Mode_IN_FLOATING;
GPIO_InitStructure.GPIO_Speed= GPIO_Speed_50MHz;
GPIO_Init(GPIOA,&GPIO_InitStructure);
}

void UART_Init(void)
{

USART_InitTypeDefUSART_InitStructure;
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl =USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx |USART_Mode_Tx;

USART_Init(USART2,&USART_InitStructure);
// USART_ITConfig(USART2,USART_IT_RXNE, ENABLE);
// USART_ITConfig(USART2,USART_IT_TXE, ENABLE);
USART_Cmd(USART2,ENABLE);
}

void UART2_PutChar(u8 ch)
{
  USART_SendData(USART2,ch);
  while(USART_GetFlagStatus(USART2,USART_FLAG_TXE)== RESET);
}

void ADC_Configuration(void)
{
  GPIO_InitTypeDef GPIO_InitStructure;  //定义结构体
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC |RCC_APB2Periph_ADC1,ENABLE);//IO口使能设置
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;  //ADC输入管脚PC0
  GPIO_InitStructure.GPIO_Mode =GPIO_Mode_AIN;//模拟输出
  GPIO_InitStructure.GPIO_Speed =GPIO_Speed_50MHz;
  GPIO_Init(GPIOC, &GPIO_InitStructure);


  ADC_InitTypeDef ADC_InitStructure;
  ADC_DeInit(ADC1);
  ADC_InitStructure.ADC_Mode =ADC_Mode_Independent;//工作在独立模式
  ADC_InitStructure.ADC_ScanConvMode =DISABLE;//工作在单通道模式
  ADC_InitStructure.ADC_ContinuousConvMode =ENABLE;//单次模式
  ADC_InitStructure.ADC_ExternalTrigConv =ADC_ExternalTrigConv_None;//转换由软件而不是外部触发启动
  ADC_InitStructure.ADC_DataAlign =ADC_DataAlign_Right;//数据右对齐
  ADC_InitStructure.ADC_NbrOfChannel =1;//通道数目
  ADC_Init(ADC1,&ADC_InitStructure);
ADC_RegularChannelConfig(ADC1,ADC_Channel_10,1,ADC_SampleTime_239Cycles5);//使用ADC1的通道10，采样顺序为1，采样周期为239.5周期
  ADC_Cmd(ADC1,ENABLE);//使能ADC1
  ADC_ResetCalibration(ADC1);//重置校准ADC1寄存器
while(ADC_GetResetCalibrationStatus(ADC1));//获取ADC重置校准寄存器的状态
ADC_StartCalibration(ADC1);//开始ADC1的校准状态
while(ADC_GetCalibrationStatus(ADC1));//等待校准完成
  ADC_SoftwareStartConvCmd(ADC1,ENABLE);//使能ADC1的软件转换启动功能

}

void Read_ADC_Result()
{
unsigned chari,a,b,c,d;
unsigned short result;

for(i=0;i<8;i++)
{
   ADC_SoftwareStartConvCmd(ADC1,ENABLE);//启动转换
   while(!ADC_GetFlagStatus(ADC1,ADC_FLAG_EOC));//等待转换结束
   result += ADC_GetConversionValue(ADC1);
}

result = result >>3;
result = (unsignedint)(((unsigned long)result)*3300>>12);//转换为数字电压值
a = result/1000;
b =(result-a*1000)/100;
c =(result-a*1000-b*100)/10;
d =(result-a*1000-b*100-c*10);
UART2_PutChar(0x56);//'v'
UART2_PutChar(0X3D);//"="
UART2_PutChar(a+48);
UART2_PutChar(0x2e);//"."
UART2_PutChar(b+48);
UART2_PutChar(c+48);
UART2_PutChar(d+48);
UART2_PutChar(0x20);//"_"空格
}

void Delay(unsigned int x)
{
unsigned int t;
t=x;
while(t--);
}

作者: silentdawn 时间: 2016-2-22 18:35
很好,谢谢楼主!

作者: wxc19960311 时间: 2017-10-28 23:51
你好，源工程可以借鉴一下吗

欢迎光临 (http://www.51hei.com/bbs/)