Arduino 开关计数器控制两个LED神灯 -

标题: Arduino 开关计数器控制两个LED神灯 [打印本页]

作者: shanzhiyuan123 时间: 2016-5-3 10:16
标题: Arduino 开关计数器控制两个LED神灯
本帖最后由 shanzhiyuan123 于 2016-5-3 12:51 编辑

Hi,大家好。小弟是新人发帖，我想做一个Project 用Arduino记录两个开关的按键次数并且用LCD显示出来，如果哪个按键次数多，哪个led神灯就亮。时间限制大概在一分钟左右。也就是说一分钟之后比较两个开关的按键次数借此来决定打开哪个LED灯。有大神有代码吗？

这是计时器的代码：
#include <LiquidCrystal.h>
LiquidCrystal lcd(7,8,9,10,11,12);
int runTimer = 1;
int runFor = 20; // time in seconds
int buzzerPin = 13;
int relayPin=4;
int data = 0;

void setup() {
pinMode(buzzerPin, OUTPUT);
pinMode(relayPin,OUTPUT);
lcd.begin(16, 2);
}

void loop() {
if(runTimer == 1){
   digitalWrite(relayPin,LOW); // relay is OFF during countdown

   lcd.clear();
   lcd.print("TIMER=");
   //Start timer
   timer();
}
runTimer = 0;
lcd.noDisplay();
delay(250);
for(int duration = 0; duration < 100; duration ++){
   digitalWrite(buzzerPin, HIGH);
   delayMicroseconds(500);
   digitalWrite(buzzerPin, LOW);
   delayMicroseconds(500);
}
lcd.display();
delay(250);
}

void timer() {
for(int timer = runFor;timer > 0; --timer){
if(timer >= 10) {
   lcd.setCursor(6,0);
} else {
   lcd.setCursor(6,0);
   lcd.print("0");
   lcd.setCursor(7,0);
}
lcd.print(timer);
lcd.print(" SECOND!");
delay(1000);
}
lcd.setCursor(0,0);
lcd.clear();
lcd.print(" TIMER OUT!");
}

这是记录开关按键次数的代码：
#include <LiquidCrystal.h>

LiquidCrystal lcd(7,8,9,10,11,12);

const int switchPin = 5;
int hits = 0;
int switchState = 0;
int prevSwitchState = 0;

const int switchPin1 = 6;
int hits1 = 0;
int switchState1 = 0;
int prevSwitchState1 = 0;

void setup() {
  // set up the number of columns and rows on the LCD
  lcd.begin(16, 2);
  pinMode(switchPin,INPUT);

  lcd.clear();
  lcd.setCursor(0, 0);
  lcd.print("Hit the button");

  pinMode(switchPin1,INPUT);

  lcd.clear();
  lcd.setCursor(0, 0);
  lcd.print("Hit the button");
}

void loop() {

  switchState = digitalRead(switchPin);

  if (switchState != prevSwitchState) {
if (switchState == LOW) {
   hits = hits + 1;
   lcd.clear();
   lcd.setCursor(0, 1);
   lcd.print("Hits:");
   lcd.setCursor(7, 1);
   lcd.print(hits);
   lcd.setCursor(11, 1);
   lcd.print(hits1);
   delay(90);
}
  }
prevSwitchState = switchState;

  switchState1 = digitalRead(switchPin1);

  if (switchState1 != prevSwitchState1) {
if (switchState1 == LOW) {
   hits1 = hits1 + 1;
   lcd.clear();
   lcd.setCursor(0, 1);
   lcd.print("Hits:");
   lcd.setCursor(11, 1);
   lcd.print(hits1);
   lcd.setCursor(7, 1);
   lcd.print(hits);
   delay(90);
}
  }
  prevSwitchState1 = switchState1;
}

我想把这部分代码组合到一起，在倒计时的同时记录两个开关的按键次数。当倒计时结束时，停止两个开关的计数。不知道怎么做，总是一个工作另外一个就不工作。。求大神解答

欢迎光临 (http://www.51hei.com/bbs/)