单片机做的切断机 - - Powered by Discuz!

#include<reg52.h>
#include"12864.h"
#include"delay.h"
#include"i2c.h"
#include"def.h"
//uchar fer[4];
#define AT24C02 0xa0 //AT24C02 地址这个地址是自己设置的全局宏定义
//unsigned char xdata fer[40]; //外部数据存储器
sbit set=P3^2;//设置。
sbit up=P3^3;//加.
sbit down=P3^4;//减.
sbit strat=P3^5;//启动.
uchar set_num=0;
uint Changdu=10,pici=10,sudu=10,Changdu1=0,pici1=0,sudu1=0,mcsl=10;
uint i=0,o=0,k=0,count,cou=0;
uchar FFW_flag=0;
//uchar REV_flag=0;
uchar stop_flag=0;
uchar code FFW[8]={0xf1,0xf3,0xf2,0xf6,0xf4,0xfc,0xf8,0xf9};
//uchar code REV[8]={0xf9,0xf8,0xfc,0xf4,0xf6,0xf2,0xf3,0xf1};
uchar code lineA_data[]={" 福泰克 "};
uchar code lineB_data[]={" 电子有限公司 "};
uchar code lineC_data[]={" 我爱单片机 "};
uchar code line0_data[]={"长度: mm "};
uchar code line1_data[]={"切断: 000/ 次"};
uchar code line2_data[]={"速度: r/s "};
uchar code line3_data[]={"产量: 000/ PCS"};
uchar code linea0_data[]={"长度设定: mm"};//长度设定。
uchar code linea1_data[]={"切断批次: 次"};//批次设定
uchar code linea2_data[]={"速度设定: rs"};//速度设定。
uchar code linea3_data[]={"产量设定: pcs"}; //计数器
/////////////////////////////////////////////////////////
void lcd_pos(uchar X,uchar Y)
{
uchar pos;
if (X==1) {X=0x80;}
else if (X==2) {X=0x90;}
else if (X==3) {X=0x88;}
else if (X==4) {X=0x98;}
pos = X+Y ;
lcd_wcmd(pos); //显示地址
}
/////////////////////////////////////////////////////////////
void Changdu_display() //长度
{
lcd_wdat(Changdu/100%10+0x30);
lcd_wdat(Changdu/10%10+0x30);
lcd_wdat(Changdu%10+0x30);
}
void pici_display() //批次
{
lcd_wdat(pici/100%10+0x30);
lcd_wdat(pici/10%10+0x30);
lcd_wdat(pici%10+0x30);
}
void sudu_display() //速度
{
// lcd_wdat(sudu/100%10+0x30);
lcd_wdat(sudu/10%10+0x30);
lcd_wdat(sudu%10+0x30);
}
void count_display() //延时时间
{
lcd_wdat(count/100%10+0x30);
lcd_wdat(count/10%10+0x30);
lcd_wdat(count%10+0x30);
}
void display()
{
lcd_pos(1,5);
lcd_wdat(Changdu/100%10+0x30);
lcd_wdat(Changdu/10%10+0x30);
lcd_wdat(Changdu%10+0x30);
lcd_pos(2,5);
lcd_wdat(pici/100%10+0x30);
lcd_wdat(pici/10%10+0x30);
lcd_wdat(pici%10+0x30);
lcd_pos(3,5);
// lcd_wdat(sudu/100%10+0x30);
lcd_wdat(sudu/10%10+0x30);
lcd_wdat(sudu%10+0x30);
lcd_pos(4,5);
lcd_wdat(count/100%10+0x30);
lcd_wdat(count/10%10+0x30);
lcd_wdat(count%10+0x30);
}
/////////////////////////////////////////////////////////////
void display1() //设置过后的数据显示
{
lcd_pos(1,3);
lcd_wdat(Changdu/100%10+0x30);
lcd_wdat(Changdu/10%10+0x30);
lcd_wdat(Changdu%10+0x30);
delay_ms(2);
lcd_pos(2,5);
lcd_wdat(pici/100%10+0x30);
lcd_wdat(pici/10%10+0x30);
lcd_wdat(pici%10+0x30);
delay_ms(2);
lcd_pos(2,3);
lcd_wdat(pici1/100%10+0x30);
lcd_wdat(pici1/10%10+0x30);
lcd_wdat(pici1%10+0x30);
delay_ms(2);
lcd_pos(3,3);
// lcd_wdat(sudu/100%10+0x30);
lcd_wdat(sudu/10%10+0x30);
lcd_wdat(sudu%10+0x30);
delay_ms(2);
lcd_pos(4,3);
lcd_wdat(cou/100%10+0x30);
lcd_wdat(cou/10%10+0x30);
lcd_wdat(cou%10+0x30);
delay_ms(2);
lcd_pos(4,5);
lcd_wdat(count/100%10+0x30);
lcd_wdat(count/10%10+0x30);
lcd_wdat(count%10+0x30);
}
void ds_display()
{
lcd_pos(1,0);
for(i=0;i<16;i++)
{
lcd_wdat(line0_data[i]);
delay_ms(1);
}
lcd_pos(2,0);
for(i=0;i<16;i++)
{
lcd_wdat(line1_data[i]);
delay_ms(1);
}
lcd_pos(3,0);
for(i=0;i<16;i++)
{
lcd_wdat(line2_data[i]);
delay_ms(1);
}
lcd_pos(4,0);
for(i=0;i<16;i++)
{
lcd_wdat(line3_data[i]);
delay_ms(1);
}
}
////////////////////////////////初始化广告图表////////////////////////////////
void cs_display()
{
lcd_pos(1,0);
for(i=0;i<16;i++)
{
lcd_wdat(lineA_data[i]);
delay_ms(1);
}
lcd_pos(2,0);
for(i=0;i<16;i++)
{
lcd_wdat(lineB_data[i]);
delay_ms(1);
}
lcd_pos(4,0);
for(i=0;i<16;i++)
{
lcd_wdat(lineC_data[i]);
delay_ms(1);
}
}
///////////////////////////////////////////////////////////////////
void scankey()
{
uchar mun=0;
if(set==0) //设置
{
delay_ms(10);
if(set==0)
{
delay_ms(10);
while(!set);
set_num++;
lcd_clr();
lcd_pos(1,0);
for(i=0;i<16;i++)
{
lcd_wdat(linea0_data[i]);
delay_ms(1);
}
lcd_pos(2,0);
for(i=0;i<16;i++)
{
lcd_wdat(linea1_data[i]);
delay_ms(1);
}
lcd_pos(3,0);
for(i=0;i<16;i++)
{
lcd_wdat(linea2_data[i]);
delay_ms(1);
}
lcd_pos(4,0);
for(i=0;i<16;i++)
{
lcd_wdat(linea3_data[i]);
delay_ms(1);
}
display();
if(set_num==1)
{
lcd_wcmd(0x0c); //关光标关闪烁
lcd_pos(1,5);
Changdu_display();
lcd_pos(1,6);
lcd_wcmd(0x0f); //开光标并闪烁
}
if(set_num==2)
{
lcd_wcmd(0x0c); //关光标关闪烁
lcd_pos(2,5);
pici_display();
lcd_pos(2,6);
lcd_wcmd(0x0f); //开光标并闪烁
}
if(set_num==3)
{
lcd_wcmd(0x0c); //关光标关闪烁
lcd_pos(3,5);
sudu_display();
lcd_pos(3,6);
lcd_wcmd(0x0f); //开光标并闪烁
}
if(set_num==4)
{
lcd_wcmd(0x0c); //关光标关闪烁
lcd_pos(4,5);
count_display();
lcd_pos(4,6);
lcd_wcmd(0x0f); //开光标并闪烁
}
if(set_num==5)
{
set_num=0;
display();
//display1();
delay_ms(5);
lcd_wcmd(0x0c); //关光标关闪烁
write24c02(110,Changdu);
write24c02(111,pici);
write24c02(112,sudu);
write24c02(113,count);
// write24c02(114,old5);
// write24c02(115,old6);
delay_ms(1);
lcd_clr();
ds_display();
//display();
display1(); //设置过后的数据显示
}
}
}
if(set_num!=0)
{
if(down==0) //--
{
delay_ms(5);
if(down==0)
{
if(set_num==1)
{
Changdu--;
if(Changdu==0)Changdu=100;lcd_pos(1,5);Changdu_display();lcd_pos(1,6);
}
if(set_num==2)
{
pici--;
if(pici==0)pici=100;lcd_pos(2,5);pici_display();lcd_pos(2,6);
}
if(set_num==3)
{
sudu--;
if(sudu==0)sudu=30;lcd_pos(3,5);sudu_display();lcd_pos(3,6);
}
if(set_num==4)
{
count--;
if(count==0)count=100;lcd_pos(4,5);count_display();lcd_pos(4,6);
}
mun=0;
while(!down)
{
delay_ms(5);
if(mun!=100)mun++;
else
{
if(set_num==1)
{
Changdu--;
if(Changdu==0)Changdu=100;lcd_pos(1,5);Changdu_display();lcd_pos(1,6);
}
if(set_num==2)
{
pici--;
if(pici==0)pici=100;lcd_pos(2,5);pici_display();lcd_pos(2,6);
}
if(set_num==3)
{
sudu--;
if(sudu==0)sudu=30;lcd_pos(3,5);sudu_display();lcd_pos(3,6);
}
if(set_num==4)
{
count--;
if(count==0)count=100;lcd_pos(4,5);count_display();lcd_pos(4,6);
}
}
}
}
}
if(up==0) //++
{
delay_ms(5);
if(up==0)
{
if(set_num==1)
{
Changdu++;
if(Changdu>100)Changdu=0;lcd_pos(1,5);Changdu_display();lcd_pos(1,6);
}
if(set_num==2)
{
pici++;
if(pici>100)pici=0;lcd_pos(2,5);pici_display();lcd_pos(2,6);
}
if(set_num==3)
{
sudu++;
if(sudu>30)sudu=0;lcd_pos(3,5);sudu_display();lcd_pos(3,6);
}
if(set_num==4)
{
count++;
if(count>100)count=0;lcd_pos(4,5);count_display();lcd_pos(4,6);
}
mun=0;
while(!up)
{
delay_ms(5);
if(mun!=100)mun++;
else
{
if(set_num==1)
{
Changdu++;
if(Changdu>100)Changdu=0;lcd_pos(1,5);Changdu_display();lcd_pos(1,6);
}
if(set_num==2)
{
pici++;
if(pici>100)pici=0;lcd_pos(2,5);pici_display();lcd_pos(2,6);
}
if(set_num==3)
{
sudu++;
if(sudu>30)sudu=0;lcd_pos(3,5);sudu_display();lcd_pos(3,6);
}
if(set_num==4)
{
count++;
if(count>100)count=0;lcd_pos(4,5);count_display();lcd_pos(4,6);
}
}
}
}
}
}
}
void motor_ffw()
{
//圆的周长=400脉冲=10MM //1MM=10MM除以400脉冲=40脉冲
unsigned long zhongmaicong; //总脉冲
uchar i;
zhongmaicong=(Changdu*40)*mcsl;//长度*1MM*每次数量
while(zhongmaicong)
{
P1=FFW[i];
delay_ms(sudu);
i++;k++;o++;
if(i==8)i=0;
if(o==Changdu*40)
{
o=0;
cou++;
display1();
}
if(k==(Changdu*40)*mcsl)
{
pici1++;
display1();
}
zhongmaicong--;
}
FFW_flag=0;
}
//////////////////////////////////////////////////////////////////////////
void main()
{
//uchar z;
lcd_init();
lcd_clr();
init(); //初始化24C02
cs_display();//广告图表
/*********下面的一小段程序的功能为格式化密码存储区。************
******当24c02中这些存储区由于其他程序的运行而导致***************
*******所存数据发生了变化，或者密码遗忘时， ********************
******可以删掉其前面的注释线，然后重新编译下载。****************
******而将密码还原为000000后，请将下面的程序用******************
******注释屏蔽掉，重新编译、下载，方可正常使用****************/
// write24c02(110,0x00);
// write24c02(111,0x00);//24c02的第110到115地址单元作为密码存储区
// write24c02(112,0x00);
// write24c02(113,0x00);
// write24c02(114,0x00);
// write24c02(115,0x00);
//////////////////////////////////////////////////////////
Changdu=read24c02(110);
pici=read24c02(111);
sudu=read24c02(112);
count=read24c02(113);
delay_ms(100);
ds_display();
display1(); //设置过后的数据显示
while(1)
{
scankey();
if(set_num==0)
{
if(!strat)
{
delay_ms(2);
while(!strat)
{
motor_ffw();
display1(); //设置过后的数据显示
}
}
}
if((up==0)&down==0)
{
delay_ms(2);
if((up==0)&down==0)
{
while(!(up&down));
{
pici1=0;cou=0;
display1();
}
}
}
}
}
/*void timer0()interrupt 1
{
TH0=(65536-50000)/256;
TL0=(65536-50000)%256;
a++;
if(a==2)
{
a=0;
keyprocess();
}
TR0=0;
}*/

复制代码