新型摇摇棒制作带走你的白富美 -

/*********************************************************************************************
程序名：　　 SHOOK16摇摇棒控制程序
编写人：　　杜洋　
硬件支持：　　STC12C5A60S2 内部RC时钟
接口说明：　　单片机P0、P2侧并行排列16个贴片LED（自P2.0开始（-））
修改日志：
[TEST测试版]　　
　　1-200911122244 在主函数写入简单程序测试惯性开关是否正常，通过测试并备份。（备）
2-200911130112 往返摇动双重显示实验成功，目前已经达到摇摇棒功能的基本要求。（备）
[V1正式版]
3-200911130309 加入了3个字幕内容，通过敲击切换字幕。（备）
4-200911131910 为网站照片重新设计方案并重定义了IO接口。（备）
/*********************************************************************************************
说明：
了解字幕的修改方法，请参考《mini1608字模设计方法》
V1正式版
# 硬件制作只需要单片机、LED、电池和导线，制作非常简单。
# 采用STC增强型单片机。
/*********************************************************************************************/
#include <STC12C5A60S2.H> //单片机头文件
unsigned char MENU;
#define DY_DELAY 5 //设置每一个点显示的时间长度（1~20）
sbit KEY1 = P1 ^ 2; //摇动惯性开关
sbit KEY2 = P1 ^ 3;
sbit KEY3 = P1 ^ 4; //选择键（大力横向碰击触发）
sbit LED1 = P0 ^ 3; //LED灯定义，低电平时亮（自上到下）
sbit LED2 = P0 ^ 4;
sbit LED3 = P0 ^ 5;
sbit LED4 = P0 ^ 6;
sbit LED5 = P0 ^ 7;
sbit LED6 = P4 ^ 6;
sbit LED7 = P4 ^ 5;
sbit LED8 = P4 ^ 4;
sbit LED9 = P2 ^ 7;
sbit LED10 = P2 ^ 6;
sbit LED11 = P2 ^ 5;
sbit LED12 = P2 ^ 4;
sbit LED13 = P2 ^ 3;
sbit LED14 = P2 ^ 2;
sbit LED15 = P2 ^ 1;
sbit LED16 = P2 ^ 0;
/*********************************************************************************************/
unsigned char code logo[] = { // (取码：从上到下从左到右，纵向8位下高位）
0x00,0x00,0x10,0x0E,0xD0,0x01,0xFF,0xFF,//杜
0xFF,0xFF,0x90,0x01,0x10,0x43,0x40,0x40,
0x40,0x40,0x40,0x40,0xFF,0x7F,0xFE,0x7F,
0x40,0x40,0x60,0x40,0x40,0x60,0x00,0x40,
0x00,0x00,0x10,0x04,0xE1,0x78,0x4E,0xFE,//洋
0x8C,0x63,0x60,0x00,0x00,0x04,0x49,0x04,
0x4A,0x04,0x4E,0x04,0xF8,0xFF,0xFC,0xFF,
0x4E,0x04,0x6B,0x04,0x4A,0x06,0x00,0x04,
0x00,0x00,0x00,0x40,0x04,0x40,0x04,0x40,//工
0x04,0x40,0x04,0x40,0x04,0x40,0xFC,0x7F,
0xFC,0x7F,0x04,0x40,0x04,0x40,0x04,0x40,
0x06,0x40,0x04,0x60,0x00,0x40,0x00,0x00,
0x00,0x00,0x80,0x00,0x60,0x00,0xF8,0xFF,//作
0xEF,0x7F,0x06,0x00,0x40,0x00,0x30,0x00,
0x1C,0x00,0xFF,0xFF,0xFA,0xFF,0x48,0x04,
0x48,0x04,0x68,0x04,0x4C,0x06,0x08,0x04,
0x00,0x00,0x08,0x00,0x1C,0x80,0x0E,0x81,//室
0x94,0x8B,0xD4,0x89,0x75,0x89,0x37,0xFF,
0x16,0xFF,0x34,0x89,0xD4,0x89,0x94,0x8B,
0x1C,0x81,0x0E,0xC0,0x04,0x80,0x00,0x00
};
/*********************************************************************************************/
unsigned char code logo1[] = { // “DoYoung” (取码：从上到下从左到右，纵向8位下高位）
0x04,0x08,0xFC,0x0F,0xFC,0x0F,0x04,0x08, // -D-
0x0C,0x0C,0xF8,0x07,0xF0,0x03,0x00,0x00,
0xC0,0x07,0xE0,0x0F,0x20,0x08,0x20,0x08, // -o-
0x20,0x08,0xE0,0x0F,0xC0,0x07,0x00,0x00,
0x00,0x00,0x3C,0x00,0x7C,0x08,0xC0,0x0F, // -Y-
0xC0,0x0F,0x7C,0x08,0x3C,0x00,0x00,0x00,
0xC0,0x07,0xE0,0x0F,0x20,0x08,0x20,0x08, // -o-
0x20,0x08,0xE0,0x0F,0xC0,0x07,0x00,0x00,
0xE0,0x07,0xE0,0x0F,0x00,0x08,0x00,0x08, // -u-
0xE0,0x07,0xE0,0x0F,0x00,0x08,0x00,0x00,
0x20,0x00,0xE0,0x0F,0xC0,0x0F,0x20,0x00, // -n-
0x20,0x00,0xE0,0x0F,0xC0,0x0F,0x00,0x00,
0xC0,0x27,0xE0,0x6F,0x20,0x48,0x20,0x48, // -g-
0xC0,0x7F,0xE0,0x3F,0x20,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, //空格
0x18,0x06,0x3C,0x0E,0x64,0x08,0x44,0x08, // -S-
0xC4,0x08,0x9C,0x0F,0x18,0x07,0x00,0x00,
0x20,0x00,0x20,0x00,0xF8,0x07,0xFC,0x0F, // -t-
0x20,0x08,0x20,0x0C,0x00,0x04,0x00,0x00,
0xE0,0x07,0xE0,0x0F,0x00,0x08,0x00,0x08, // -u-
0xE0,0x07,0xE0,0x0F,0x00,0x08,0x00,0x00,
0x80,0x07,0xC0,0x0F,0x60,0x08,0x24,0x08, // -d-
0xFC,0x07,0xFC,0x0F,0x00,0x08,0x00,0x00,
0x00,0x00,0x00,0x00,0x20,0x08,0xEC,0x0F, // -i-
0xEC,0x0F,0x00,0x08,0x00,0x00,0x00,0x00,
0xC0,0x07,0xE0,0x0F,0x20,0x08,0x20,0x08, // -o-
0x20,0x08,0xE0,0x0F,0xC0,0x07,0x00,0x00,
};
/*********************************************************************************************/
unsigned char code logo2[] = { // “与电子爱好者同行” (取码：从上到下从左到右，纵向8位下高位）
0x00,0x00,0x00,0x08,0x00,0x08,0x80,0x08,
0xFF,0x09,0xFE,0x08,0x88,0x08,0x88,0x08,
0x88,0x08,0x88,0x08,0x88,0x0C,0x88,0x48,
0x88,0xC0,0x8C,0x7F,0xC8,0x3F,0x80,0x00,
0x00,0x00,0x00,0x00,0xF8,0x0F,0xF0,0x07,
0x90,0x04,0x90,0x04,0x90,0x04,0xFF,0x7F,
0xFE,0xFF,0x90,0xC4,0x90,0xC4,0x90,0xC4,
0xF0,0xCF,0xF8,0xC7,0x10,0xF0,0x00,0x40,
0x00,0x00,0x80,0x00,0x80,0x00,0x80,0x00,
0x82,0x00,0x82,0x00,0x82,0x40,0x82,0x40,
0xE2,0xFF,0xF2,0x7F,0x9A,0x00,0x8E,0x00,
0x87,0x00,0x82,0x00,0xC0,0x00,0x80,0x00,
0x00,0x00,0x40,0x00,0xE0,0x40,0x74,0x20,
0xA4,0x98,0xAC,0x8E,0xFA,0x47,0xE2,0x6F,
0xBE,0x3A,0xAA,0x12,0xB2,0x3A,0xBF,0x6E,
0xAB,0x67,0xE2,0xC2,0x70,0xC0,0x20,0x40,
0x00,0x00,0x20,0x80,0x20,0x63,0xF8,0x37,
0xFF,0x1C,0x26,0x0F,0xF0,0x7B,0xE0,0x30,
0x82,0x00,0x82,0x20,0x82,0x40,0xF2,0xFF,
0xEA,0x7F,0x8E,0x00,0xC7,0x00,0x82,0x00,
0x00,0x00,0x40,0x04,0x40,0x04,0x44,0x02,
0x44,0xFF,0x44,0x7F,0xC4,0x49,0xFF,0x49,
0x7F,0x49,0x64,0x49,0x66,0x49,0x54,0xFF,
0xD8,0x7F,0x4E,0x01,0x64,0x00,0x40,0x00,
0x00,0x00,0x00,0x00,0xFF,0xFF,0xFE,0x7F,
0x12,0x00,0xD2,0x1F,0x92,0x0F,0x92,0x08,
0x92,0x08,0x92,0x1F,0xDA,0x4F,0x92,0x40,
0xFE,0xFF,0xFF,0x7F,0x02,0x00,0x00,0x00,
0x00,0x00,0x20,0x04,0x10,0x02,0x8C,0xFF,
0xE7,0x7F,0x42,0x00,0x00,0x00,0x20,0x00,
0x22,0x00,0x22,0x40,0x22,0x40,0xE2,0xFF,
0xE2,0x7F,0x23,0x00,0x32,0x00,0x20,0x00
};
/*********************************************************************************************
函数名：LED显示用延时函数
调用：delay(?);
参数：1~65535（参数不可为0）
返回值：无
结果：占用CPU方式延时与参数数值相同的毫秒时间
备注：应用于1T单片机时i<600，应用于12T单片机时i<125
/*********************************************************************************************/
void delay (unsigned int a){ // 用于点扫描的延时
unsigned int i;
while( --a != 0){
for(i = 0; i < 1; i++);
}
}
/*********************************************************************************************/
/*********************************************************************************************
函数名：毫秒级CPU延时函数
调用：DELAY_MS (?);
参数：1~65535（参数不可为0）
返回值：无
结果：占用CPU方式延时与参数数值相同的毫秒时间
备注：应用于1T单片机时i<600，应用于12T单片机时i<125
/*********************************************************************************************/
void DELAY_MS (unsigned int a){
unsigned int i;
while( --a != 0){
for(i = 0; i < 600; i++);
}
}
/*********************************************************************************************/
/*********************************************************************************************
函数名：关闭所有LED灯（操作硬件）
调用：DISPLAY_OFF();
参数：无
返回值：无
结果：所有LED灯熄灭
备注：
/**********************************************************************************************/
void DISPLAY_OFF (void){
delay(DY_DELAY);//显示停留
P0 = 0xff;
P2 = 0xff;
P4 = 0xff;
}
/**********************************************************************************************/
/*********************************************************************************************
函数名：单帧数据送入显示（操作硬件）
调用：DISPLAY_PIN(?,?);
参数：16位显示数据（下高位）（d：上面8位，e：下面8位）
返回值：无
结果：点亮对应数据的LED灯
备注：
/**********************************************************************************************/
void DISPLAY_PIN (unsigned char d,unsigned char e){ //第1列横向显示程序
unsigned char i;
i = d & 0x01;
if(i == 0x01){LED1 = 0;}DISPLAY_OFF();
i = d & 0x02;
if(i == 0x02){LED2 = 0;}DISPLAY_OFF();
i = d & 0x04;
if(i == 0x04){LED3 = 0;}DISPLAY_OFF();
i = d & 0x08;
if(i == 0x08){LED4 = 0;}DISPLAY_OFF();
i = d & 0x10;
if(i == 0x10){LED5 = 0;}DISPLAY_OFF();
i = d & 0x20;
if(i == 0x20){LED6 = 0;}DISPLAY_OFF();
i = d & 0x40;
if(i == 0x40){LED7 = 0;}DISPLAY_OFF();
i = d & 0x80;
if(i == 0x80){LED8 = 0;}DISPLAY_OFF();
i = e & 0x01;
if(i == 0x01){LED9 = 0;}DISPLAY_OFF();
i = e & 0x02;
if(i == 0x02){LED10 = 0;}DISPLAY_OFF();
i = e & 0x04;
if(i == 0x04){LED11 = 0;}DISPLAY_OFF();
i = e & 0x08;
if(i == 0x08){LED12 = 0;}DISPLAY_OFF();
i = e & 0x10;
if(i == 0x10){LED13 = 0;}DISPLAY_OFF();
i = e & 0x20;
if(i == 0x20){LED14 = 0;}DISPLAY_OFF();
i = e & 0x40;
if(i == 0x40){LED15 = 0;}DISPLAY_OFF();
i = e & 0x80;
if(i == 0x80){LED16 = 0;}DISPLAY_OFF();
}
/*********************************************************************************************
函数名：初始化程序
调用：init();
参数：无
返回值：无
结果：设计IO接口为强推方式并全部置1
备注：
/**********************************************************************************************/
void init (void){
P4SW = 0xff; //启动P4接口
P0M0 = 0xff; //接口设置为强推
P2M0 = 0xff;
P4M0 = 0xff;
P1 = 0xff; //初始IO接口状态
P0 = 0xff;
P2 = 0xff;
P4 = 0xff;
}
/**********************************************************************************************/
/*********************************************************************************************
函数名：主函数
调用：无
参数：无
返回值：无
结果：程序开始处，无限循环
备注：
/**********************************************************************************************/
void main (void){
unsigned char a,c;
init();//初始程序
while(1){
if(MENU > 2){
MENU = 0;
}
if(MENU == 0){ //字幕1
if(KEY2 == 0){
DELAY_MS(20);
while(KEY2 == 0);
c = 0;
for(a=1;a<80;a++){ //这里的“80”是这个字幕需要扫描的列数，修改字幕时必须修改此参数。
DISPLAY_PIN (logo[c],logo[c+1]); //“LOGO”是第一个字幕的数据表名
c=c+2;//产生显示行移位
}
}
if(KEY1 == 0){
DELAY_MS(20);
while(KEY1 == 0);
c = 158;
for(a=1;a<80;a++){
DISPLAY_PIN (logo[c],logo[c+1]);
c=c-2;//产生显示行移位
}
}
if(KEY3 == 0){
DELAY_MS(20);
while(KEY3 == 0);
MENU++;
}
}
if(MENU == 1){ //字幕2
if(KEY2 == 0){
DELAY_MS(20);
while(KEY2 == 0);
c = 0;
for(a=1;a<108;a++){
DISPLAY_PIN (logo1[c],logo1[c+1]);
c=c+2;//产生显示行移位
}
}
if(KEY1 == 0){
DELAY_MS(20);
while(KEY1 == 0);
c = 214;
for(a=1;a<108;a++){
DISPLAY_PIN (logo1[c],logo1[c+1]);
c=c-2;//产生显示行移位
}
}
if(KEY3 == 0){
DELAY_MS(20);
while(KEY3 == 0);
MENU++;
}
}
if(MENU == 2){ //字幕3
if(KEY2 == 0){
DELAY_MS(20);
while(KEY2 == 0);
c = 0;
for(a=1;a<128;a++){
DISPLAY_PIN (logo2[c],logo2[c+1]);
c=c+2;//产生显示行移位
}
}
if(KEY1 == 0){
DELAY_MS(20);
while(KEY1 == 0);
c = 254;
for(a=1;a<128;a++){
DISPLAY_PIN (logo2[c],logo2[c+1]);
c=c-2;//产生显示行移位
}
}
if(KEY3 == 0){
DELAY_MS(20);
while(KEY3 == 0);
MENU++;
}
}
}
}
/**********************************************************************************************
/**********************************************************************************************/
/*************************************************************
* 杜洋工作室 DoYoung Studio
/*************************************************************/

复制代码