电阻电容电感芯片主程序 -

标题: 电阻电容电感芯片主程序 [打印本页]

作者: ning21 时间: 2017-5-6 09:03
标题: 电阻电容电感芯片主程序
/************************************
*********STC89C51**********
**********12MHz晶振********/

#include "reg51.h"

#define uint8 unsigned char
#define uint16 unsigned int
#define uchar unsigned char
#define uint unsigned int

uint16 cnt2ms; //10ms计数器
uint8 cnt1s; //1秒计数器

//电阻--------------------------------


#define       Z1 13910053.00
#define       Z2 3685279.00

float RZ=0;
unsigned long RX=0;
unsigned long RX2=0;
unsigned long RX3=0;
unsigned long RX4=0;
unsigned long RX5=0;
unsigned long RX6=0;
unsigned long RX7=0;
unsigned long RX8=0;
unsigned long RX9=0;

//电感--------------------------------
float LZ=0;
#define       C1 0.05

//电容--------------------------------
float CZ=0;
float CX=0;

unsigned char I=0;
long tom;
unsigned int Pulsecnt=0; //脉冲个数
unsigned int Pulsenum; //脉冲个数
uint8 start=0; //
uint16 PulseTime; //10ms计数器
uint16 Pulse; //10ms计数器
bit flag=0;
uint8 CH=0; //
unsigned long x;
unsigned char LED_s=0;



/********************************按键*****************************************/
sbit K1=P1^0;
sbit K2=P1^1;
sbit K3=P1^2;
sbit DIP=P0^7;

sbit L1=P1^3;
sbit L10=P1^4;
sbit L100=P1^5;

sbit A0=P2^0;
sbit A1=P2^1;

sbit RED=P2^4;
sbit GRE=P2^3;
sbit YEW=P2^2;

unsigned char temp[7];

/********************************0 1 2 3 4 5 6 7 8 9 H L */
unsigned char code dispcode[]={0xC0,0xF9,0xA4,0xB0,0x99,0x92,0x82,0xF8,0x80,0x90,0x89,0xC7};
//数码管位选
sbit B4 = P2^7;
sbit B1 = P3^7;
sbit B2 = P2^5;
sbit B3 = P2^6;

/****延时******/
void delay_1ms(uint x)
{
uint j;
uchar i;
for(j=0;j<x;j++)
{
for(i=0;i<120;i++);
}
}
void Key_SM(void){

      if(K1==0){
         delay_1ms(5);
         if(K1==0){
            YEW=1;RED=1;GRE=0;
            GRE=0;

            //----电感档-------
            A0=0;
            A1=0;
            CH=2;//电感档

            while(K1==0){}

               }
         }

      if(K2==0){
         delay_1ms(5);
         if(K2==0){
               YEW=1;GRE=1;
            RED=0;

            //----电阻档-------
            A0=1;
            A1=0;
            CH=1;//电阻档

            while(K2==0){}
                  }

            }

   if(K3==0){
         delay_1ms(5);
         if(K3==0){
            YEW=0;GRE=1;RED=1;

            //----电容档-------
            A0=0;
            A1=1;
            CH=3;//电容挡
            while(K3==0){}
                     }

            }

}

//--------------------主程序--------------------------------
void main()
{

   TMOD=0x51;       //设置定时器0，方式1:16位定时器
   TH1=0;
   TL1=0;
   TH0=(65536-2000)/256; //设定定时周期
   TL0=(65536-2000)%256;
   TR0=1;
   TR1=1;
   ET1=1;
   ET0=1;
   EA=1;
//----电阻档-------
            //----电阻档-------
            A0=1;
            A1=0;
            CH=1;//电阻档

YEW=1;GRE=1;RED=0;

while(1)
{

   Key_SM();
if(flag==1){

      flag=0;

      x=Pulsenum*65536+TH1*256+TL1;//计算1s内的脉冲个数，频率=脉冲个数
if(CH==1){


   RZ=(Z1/x);//测量1K到1000K
      RX=RZ-1000;
      RX=RX>>1;//RX/2

      RX=RX*10;//数值扩大10倍
if(RX>=10109){//减去1K阻值
      RX=RX-10109;
}else{RX=0;}

if(x==0){RX=0;RX2=0;RX3=0;RX4=0;RX5=0;RX6=0;RX7=0;RX8=0;RX9=0;}//无脉冲后所有的数字归零

  if(RX>9999999){RX=9999999; }//RX大于9999999，则RX=9999999

            RX2=(RX+RX3+RX4+RX5+RX6+RX7+RX8+RX9)>>3;//求平均提高精度

RX9=RX8;RX8=RX7;RX7=RX6;RX6=RX5;RX5=RX4;RX4=RX3;RX3=RX;//数值往后移动保存上一次的阻值


//RX2=RX2/10;
if(RX2<=9999){RX2=RX2;L1=1;L10=1;L100=1;}
if(RX2<=99999&&RX2>9999){RX2=RX2/10;L1=0;L10=1;L100=1;}
if(RX2<=999999&&RX2>99999){RX2=RX2/100;L1=1;L10=0;L100=1;}
if(RX2>999999){RX2=RX2/1000;L1=1;L10=1;L100=0;}
tom=RX2;


temp[0] = tom/1000;
tom = tom%1000;
temp[1] = tom/100;
tom = tom%100;
temp[2] = tom/10;
tom = tom%10;
temp[3] = tom;

}
if(CH==2){


      LZ=(x*37*C1)/1000000;
      LZ=LZ*x;
      LZ=1000000/LZ;
if(x==0)LZ=0;
  if(LZ>999999)LZ=999999; //限制最高值
      //更新电感值显示



if(LZ<=9999){LZ=LZ;L1=1;L10=1;L100=1;}
if(LZ<=99999&&LZ>9999){LZ=LZ/10;L1=0;L10=1;L100=1;}
if(LZ<=999999&&LZ>99999){LZ=LZ/100;L1=1;L10=0;L100=1;}
if(LZ>999999){LZ=LZ/1000;L1=1;L10=1;L100=0;}

tom=LZ;

temp[0] = tom/1000;
tom = tom%1000;
temp[1] = tom/100;
tom = tom%100;
temp[2] = tom/10;
tom = tom%10;
temp[3] = tom;

}
if(CH==3){

   CZ=6600000/x;
if(x==0||x>30500)CZ=0;

  if(CZ>999999)CZ=999999;  //限制最高值
      //更新电容值显示
if(CZ<=9999){CZ=CZ;L1=1;L10=1;L100=1;}
if(CZ<=99999&&CZ>9999){CZ=CZ/10;L1=0;L10=1;L100=1;}
if(CZ<=999999&&CZ>99999){CZ=CZ/100;L1=1;L10=0;L100=1;}
if(CZ>999999){LZ=CZ/1000;L1=1;L10=1;L100=0;}

tom=CZ;

temp[0] = tom/1000;
tom = tom%1000;
temp[1] = tom/100;
tom = tom%100;
temp[2] = tom/10;
tom = tom%10;
temp[3] = tom;

}
      cnt2ms=0;
      Pulsenum=0;
      TH1=0;
      TL1=0;
      TR1=1;

}

}
}
/*******************************************************************************
* 函数名: Exti0_interrupt
* 函数功能: /T0引脚下降沿进入中断
* 入口参数: 无
* 返回: 无
*******************************************************************************/
void T1_interrupt(void) interrupt 3 using 0
{

  Pulsenum++; //保存测得脉搏值

}
/********************************************************************
函数功能：定时器/计数器1中断处理
入口参数：null
返回：null
备注：null
********************************************************************/
void Timer0IntProc() interrupt 1 using 0 //2ms
{
  TH0=(65536-2000)/256;
  TL0=(65536-2000)%256;
cnt2ms++;

I++;
//数码管扫描

if(I==1){B2=1;B3=1;B4=1;B1=0;
      P0=dispcode[temp[0]];DIP=1;
      }
if(I==2){B1=1;B3=1;B4=1;B2=0;
      P0=dispcode[temp[1]];DIP=1;
      }
if(I==3){B1=1;B2=1;B4=1;B3=0;
      P0=dispcode[temp[2]];

if(CH==1){DIP=0;}
      }
if(I==4){B1=1;B2=1;B3=1;B4=0;I=0;DIP=1;
      P0=dispcode[temp[3]];
      }

if(cnt2ms==497) //1s计时到
{

      TR1=0;


      cnt2ms = 0;

      flag=1;
}

}

作者: zf@@zf 时间: 2020-4-23 23:25
  LZ=(x*37*C1)/1000000;
      LZ=LZ*x;
      LZ=1000000/LZ;
if(x==0)LZ=0;
这几行代码是什么意思呢

欢迎光临 (http://www.51hei.com/bbs/)