标题: 基于单片机的恒温系统控制（程序） [打印本页]
作者: cylyelyn 时间: 2017-6-5 09:54
标题: 基于单片机的恒温系统控制（程序）
源程序清单如下：
//ds18b20 driveprogram
//for 51 mcuwith lcd1602 display
#include"reg52.h"
#include<intrins.h>
/*******************************************************************/
#define HIGH 1 //高电平
#define LOW 0 //低电平
#define TRUE 1 //真
#define ZERO 0 //假
#define MSB 0x80
//ds18b20 part
#define SkipRom 0xcc
#defineConvertTemperature 0x44
#define Read Scratchpad 0xbe
sbitOne_Wire_Bus=P1^6;
void One_ Wire_ Delay(unsigned char delay_ time);
voidOne_Wire_Write_Byte (unsigned char oww_dat);
unsigned charOne_Wire_Read_Byte(void);
voidRead_18B20(void);
voidInitize_One_Wire_Bus(void);
voiddelay(void);
/********************************************************************/
data unsignedchar GetScratchpad[2];
code unsignedchardecimalH[16]={00,06,12,18,25,31,37,43,50,56,62,68,75,81,87,93};
code unsignedchar decimalL[16]={00,25,50,75,00,25,50,75,00,25,50,75,00,25,50,75};
unsigned charResult Temperature H;//经过处理后的温度整数部分
unsigned charResult Temperature L H, Result Temperature LL;//经过处理后的温度的小数部分
data unsignedchar ResultSignal;//温度为负数标志位
/********************************************************************/
voidInitize_One_Wire_Bus(void)
{One_Wire_Bus=0;
One_Wire_Delay (80); / /Bus master pulling low488us
One_Wire_Bus=1;
One_Wire_Delay (25);//Resister pull up 158us;}
/********************************************************************/
/*******************ds18b20 **********************************/
voidOne_Wire_Delay (unsigned char delay_time)
{
While (delay_time) delay_time--;//Delay timeus :=(8+delay_time*6)us;
}
/********************************************************************/
unsigned charOne_Wire_Read_Byte (void)
{
bit temp_bit;
unsigned char i,result=0;
for (i=0; i<8;i++)
{
One_Wire_Bus=0;
One_Wire_Bus=1;
temp_bit=One_Wire_Bus;
One_Wire_Delay (9); //delay 62 us
If (temp_bit)
result|=0x01<<i;
}
Return (result);
}
/********************************************************************/
voidOne_Wire_Write_Byte(unsigned char oww_dat)
{
unsigned char i;
for (i=0;i<8;i++)
{
One_Wire_Bus=0;
if(oww_dat&0x01)One_Wire_Bus=1;
One_Wire_Delay (20); //delay 128 us
One_Wire_Bus=1;
oww_dat>>=1;
}
One_Wire_Delay (10);
}
/********************************************************************/
void Read_18B20 (void)
{
unsigned char tempH,tempL;
Initize_One_Wire_Bus ();
One_Wire_Write_Byte (SkipRom);
_nop_();
One_Wire_Write_Byte (ConvertTemperature);
One_Wire_Delay (5);
Initize_One_Wire_Bus ();
One_Wire_Write_Byte (SkipRom);
_nop_();
One_Wire_Write_Byte (ReadScratchpad);
GetScratchpad[0]=One_Wire_Read_Byte();//从DS18B20读出的低8位温度值
GetScratchpad[1]=One_Wire_Read_Byte();//从DS18B20读出的高8位温度值
One_Wire_Delay (120);
tempH=(GetScratchpad[1]<<4)|(GetScratchpad[0]>>4); //温度的整数部分
tempL=(GetScratchpad[0]&0x0f); //温度的小数部分
Initize_One_Wire_Bus();
if(tempH&0x80) //判断温度的正负值
{
tempH=~tempH;
tempL=~tempL+1;
ResultSignal=1;//温度为负数标志位
}
Result Temperature H=tempH;//经过处理后的温度的整数部分
Result Temperature L=decimalL[tempL]; //经过处理的温度的小数部分十分位
Result Temperature LH=decimalH[tempL];//经过处理的温度的小数部分的百分位
}
/********************************************************************/
/*******************************************************************/
//lcd part
#define LINE1 0
#define LINE2 1
#define LINE1_HEAD 0x80
#define LINE2_HEAD 0xC0
#define LCD_DELAY_TIME 40
#define DATA_MODE 0x38
#define OPEN_SCREEN 0x0C
#define DISPLAY_ADDRESS 0x80
#define CLEARSCREEN LCD_en_command(0x01)
#define COMMAND_SLOT
LCD1602_RS=LOW;LCD1602_RW=LOW;LCD1602_EN=LOW
#define DATA_SLOT
LCD1602_RS=HIGH;LCD1602_RW=LOW;LCD1602_EN=LOW
//common part
#define HIGH 1 //高电平
#define LOW 0 //低电平
#define TRUE 1 //真
#define ZERO 0 //假
#define MSB 0x80
//change thispart at different board
#define LCDIO P0
sbitLCD1602_RS=P1^0; //数据命令选择 1 data 0 command
sbitLCD1602_RW=P1^1; //读写选择 1 read 0 write
sbitLCD1602_EN=P1^2; //LCD使能信号
//function define
/********************************************************************/
voidLCD_delay(void);//lcd 延时函数
voidLCD_en_command(unsigned char command);//写命令
voidLCD_en_dat(unsigned char temp);//写数据
void LCD_set_xy(unsigned char x, unsigned char y );//设置显示地址
voidLCD_write_char( unsigned x,unsigned char y,unsigned char dat);//write lcd acharacter function
void LCD_write_string(unsigned char X,unsigned char Y,unsigned char*s);//write lcd string function
voidLCD_init(void);//lcd 初始化.
//unsigned char code mytab[8]= {0x0C,0x12,0x12,0x0C,0x00,0x00,0x00,0x00};//自定义字符
/********************************************************************/
/* 自定义字符写入CGRAM */
/*******************************************************************/
void writetab()
{ unsigned char i;
LCD_en_command(0x40);
for(i=0;i<8;i++)
LCD_en_dat(mytab); }
/********************************************************************/
/******************** LCD PART*************************************/
voidLCD_delay(void)
{ unsigned chari;
for(i=LCD_DELAY_TIME;i>ZERO;i--);//be surelcd reset
}
/********************************************************************/
voidLCD_en_command(unsigned char command)
{
LCDIO=command;
COMMAND_SLOT;
LCD_delay();
LCD1602_EN=HIGH;
}
/********************************************************************/
voidLCD_en_dat(unsigned char dat)
{
LCDIO=dat;
DATA_SLOT;
LCD_delay();
LCD1602_EN=HIGH;
}
/********************************************************************/
void LCD_set_xy(unsigned char x, unsigned char y )
{
unsigned char address;
if (y == LINE1)
address = LINE1_HEAD + x;
else address = LINE2_HEAD + x;
LCD_en_command(address);
}
/********************************************************************/
voidLCD_write_char( unsigned x,unsigned char y,unsigned char dat)
{ LCD_set_xy( x, y );
LCD_en_dat(dat); }
/********************************************************************/
voidLCD_write_string(unsigned char X,unsigned char Y,unsigned char *s)
{ LCD_set_xy( X, Y ); //set address
while (*s) // write character
{ LCDIO=*s; LCD_en_dat(*s);
s ++;}
}
/********************************************************************/
voidLCD_init(void)
{
unsigned char i;
CLEARSCREEN;//clear screen
LCD_en_command(DATA_MODE);//set 8 bit datatransmission mode
LCD_en_command(OPEN_SCREEN);//open display(enable lcd display)
LCD_en_command(DISPLAY_ADDRESS);//set lcdfirst display address
CLEARSCREEN;//clear screen
for(i=0;i<15;i++)
LCD_delay();
}
#defineuint unsigned int
#define uchar unsigned char
void delay(void)
{
uint x;
for(x=0;x<1000;x++);
}
uchar key()
{
uchar count,cmd,key;
key=0;
while(key==0)
{ P2=0x0f;
if(P2!=0x0f)
{ delay();
if(P2!=0x0f)
{ cmd=0xef;
for(count=0;count<2;count++)
{ P2=cmd;
if((P2&0x0f)!=0x0f)
{ key=(cmd&0xf0)+(P2&0x0f);
key=~key;
break;}
else
cmd=(cmd<<1)+1;
}
}
// else return 0x00;
}
// else return 0x00;
}
P2=0x0f;
while(P2!=0x0f);
return(key);
}
int keyscan()
{
uchar i,keycode;
i=keybd();
switch(i)
{ case 0x11:{keycode=1;}break;
case 0x12:{keycode=2;}break;
case 0x14:{keycode=3;}break;
case 0x18:{keycode=4;}break;
case 0x21:{keycode=5;}break;
case 0x22:{keycode=6;}break;
case 0x24:{keycode=7;}break;
case 0x28:{keycode=8;}break;
default:{keycode=0;}break;
}
return keycode;
作者: liyuqi 时间: 2021-4-8 12:07
这段代码是要实现什么功能呢
| 欢迎光临 (http://www.51hei.com/bbs/) |
Powered by Discuz! X3.1 |