stc15系列单片机与pc串口检测子程序程序 -

#include"SERIAL_OUTOUT.H"
#include "reg51.h"
#include "intrins.h"
#define FOSC 18432000L //系统频率
#define BAUD 115200 //串口波特率
#define NONE_PARITY 0 //无校验
#define ODD_PARITY 1 //奇校验
#define EVEN_PARITY 2 //偶校验
#define MARK_PARITY 3 //标记校验
#define SPACE_PARITY 4 //空白校验
#define PARITYBIT EVEN_PARITY //定义校验位
bit busy;
sbit P22 = P2^2;
#define S1_S0 0x40 //P_SW1.6
#define S1_S1 0x80 //P_SW1.7
/*----------------------------
发送串口数据
----------------------------*/
void Init_serial()
{
ACC = P_SW1;
ACC &= ~(S1_S0 | S1_S1); //S1_S0=0 S1_S1=0
P_SW1 = ACC; //(P3.0/RxD, P3.1/TxD)
// ACC = P_SW1;
// ACC &= ~(S1_S0 | S1_S1); //S1_S0=1 S1_S1=0
// ACC |= S1_S0; //(P3.6/RxD_2, P3.7/TxD_2)
//P_SW1 = ACC;
//
// ACC = P_SW1;
// ACC &= ~(S1_S0 | S1_S1); //S1_S0=0 S1_S1=1
// ACC |= S1_S1; //(P1.6/RxD_3, P1.7/TxD_3)
// P_SW1 = ACC;
#if (PARITYBIT == NONE_PARITY)
SCON = 0x50; //8位可变波特率
#elif (PARITYBIT == ODD_PARITY) || (PARITYBIT == EVEN_PARITY) || (PARITYBIT == MARK_PARITY)
SCON = 0xda; //9位可变波特率,校验位初始为1
#elif (PARITYBIT == SPACE_PARITY)
SCON = 0xd2; //9位可变波特率,校验位初始为0
#endif
T2L = (65536 - (FOSC/4/BAUD)); //设置波特率重装值
T2H = (65536 - (FOSC/4/BAUD))>>8;
AUXR = 0x14; //T2为1T模式, 并启动定时器2
AUXR |= 0x01; //选择定时器2为串口1的波特率发生器
ES = 1; //使能串口1中断
EA = 1;
}
void SendData(BYTE dat)
{
while (busy); //等待前面的数据发送完成
ACC = dat; //获取校验位P (PSW.0)
if (P) //根据P来设置校验位
{
#if (PARITYBIT == ODD_PARITY)
TB8 = 0; //设置校验位为0
#elif (PARITYBIT == EVEN_PARITY)
TB8 = 1; //设置校验位为1
#endif
}
else
{
#if (PARITYBIT == ODD_PARITY)
TB8 = 1; //设置校验位为1
#elif (PARITYBIT == EVEN_PARITY)
TB8 = 0; //设置校验位为0
#endif
}
busy = 1;
SBUF = ACC; //写数据到UART数据寄存器
}
/*----------------------------
发送字符串
----------------------------*/
void SendString(char *s)
{
while (*s) //检测字符串结束标志
{
SendData(*s++); //发送当前字符
}
}
void Uart() interrupt 4 using 1
……………………
…………限于本文篇幅余下代码请从51黑下载附件…………
单片机源程序如下:

复制代码