STM32+XPT2046触摸屏带刷卡识别的程序和教程等资料下载 -

/* 程序下载进去后D1指示灯闪烁，表示程序正常运行，按下按键K_UP可以强制触摸校正 */
#include "stm32f10x.h"
#include "led.h"
#include "system.h"
#include "gui.h"
#include "touch.h"
#include "flash.h"
#include "key.h"
#include "systick.h"
#include "tim.h"
#include "RC522.h"
#include "usart.h"
uint16_t penColor;
unsigned char data2[4] = {0,0,0,0x01};
unsigned char DefaultKey[6] = {0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF};
unsigned char g_ucTempbuf[20];
void kai_display() //开机显示
{
TFT_ClearScreen(BLACK);
GUI_Show12Char(10,103,"欢迎使用",GREEN,BLACK);
GUI_Show12Char(10,10,"K_UP:Adjust",GREEN,BLACK);
}
void lcd_display() //LCD初始化显示
{
TFT_ClearScreen(BLACK);
TFT_ClearScreen(BLACK);
GUI_Show12Char(10,50,"关门 ",RED,BLACK); //关门
GUI_Show12Char(10,150," ",YELLOW,BLACK);
}
void display_init() //初始化显示
{
TFT_ClearScreen(BLACK);
GUI_Show12Char(0, TFT_YMAX - 16, "X:", RED, BLACK);
GUI_Show12Char(56, TFT_YMAX - 16, "Y:", RED, BLACK);
GUI_Show12Char(TFT_XMAX-8*3, 0, "RST", RED, BLACK);
GUI_Show12Char(56, TFT_YMAX - 106, "一号存储:", RED, BLACK);
GUI_Show12Char(56, TFT_YMAX - 156, "二号存储:", RED, BLACK);
GUI_Show12Char(56, TFT_YMAX - 206, "三号存储:", RED, BLACK);
}
int main(void)
{
unsigned char status,i;
unsigned int temp;
uint8_t touchValue[5] = {0, 0, 0, 0, 0};
// uint32_t i;
penColor = BLUE;
RC522_Init();
/* 初始化 */
PcdReset();
PcdAntennaOff();
TFT_Init();
FLASH_Init();
LED_Config();
KEY_Config();
SYSTICK_Config();
delay_ms(10);
PcdAntennaOn();
delay_ms(10);
tim3_init(1000,7199);
uart_init(9600);
kai_display();
SYSTICK_Delay1ms(1500);
TOUCH_Init();
display_init();
while(1)
{
if(KEY_Scan()==KEY_UP) //按下K_UP按键强制校准
{
TOUCH_Adjust(); //校正
display_init();
}
if(TOUCH_Scan() == 0)
{
/* 显示X轴的物理坐标值 */
touchValue[0] = (TouchData.x % 10000 /1000) + '0';
touchValue[1] = (TouchData.x % 1000 /100) + '0';
touchValue[2] = (TouchData.x % 100 /10) + '0';
touchValue[3] = (TouchData.x % 10) + '0';
GUI_Show12Char(16, TFT_YMAX - 16, touchValue, RED, BLACK);
/* 显示Y轴的物理坐标值 */
touchValue[0] = (TouchData.y % 10000 /1000) + '0';
touchValue[1] = (TouchData.y % 1000 /100) + '0';
touchValue[2] = (TouchData.y % 100 /10) + '0';
touchValue[3] = (TouchData.y % 10) + '0';
GUI_Show12Char(72, TFT_YMAX - 16, touchValue, RED, BLACK);
}
status = PcdRequest(PICC_REQALL, g_ucTempbuf);//寻卡
if (status != MI_OK)
{
PcdReset();
PcdAntennaOff();
PcdAntennaOn();
continue;
}
printf("卡的类型:");
for(i=0;i<2;i++)
{
temp=g_ucTempbuf[i];
printf("%X",temp);
}
status = PcdAnticoll(g_ucTempbuf);//防冲撞
if(status != MI_OK)
{ continue; }
////////以下为超级终端打印出的内容////////////////////////
printf("卡序列号："); //超级终端显示,
for(i=0;i<4;i++)
{
temp=g_ucTempbuf[i];
printf("%X",temp);
}
if(g_ucTempbuf[0]==0x37&&g_ucTempbuf[1]==0x25&&g_ucTempbuf[2]==0xAA&&g_ucTempbuf[3]==0x29)
{
GUI_Show12Char(10,50,"开门 ",GREEN,BLACK); //开门
GUI_Show12Char(10,10,"姓名：一号 ",RED,BLACK);
// GPIO_SetBits(GPIOC, (uint16_t)0xff & 0x00FF);
if((TouchData.lcdx>50)&&(TouchData.lcdx<100))
{
if((TouchData.lcdy>280)&&(TouchData.lcdy<330))
{
GPIO_ResetBits(GPIOC, (~(uint16_t)0xfe) & 0x00FF);
delay_ms(50000);
// TouchData.lcdx=0;
// TouchData.lcdy=0;
// delay_ms(10);
// GPIO_SetBits(GPIOC, (uint16_t)0xfe& 0x00FF);
}
if((TouchData.lcdy>220)&&(TouchData.lcdy<270))
{
GPIO_ResetBits(GPIOC, (~(uint16_t)0xfd) & 0x00FF);
delay_ms(50000);
// TouchData.lcdx=0;
// TouchData.lcdy=0;
// delay_ms(10);
// GPIO_SetBits(GPIOC, (uint16_t)0xfd & 0x00FF);
}
if((TouchData.lcdy>120)&&(TouchData.lcdy<180))
{
GPIO_ResetBits(GPIOC, (~(uint16_t)0xfb) & 0x00FF);
delay_ms(50000);
// TouchData.lcdx=0;
// TouchData.lcdy=0;
// delay_ms(10);
// GPIO_SetBits(GPIOC, (uint16_t)0xfb & 0x00FF);
}
if ((TouchData.lcdx > TFT_XMAX-8*3) && (TouchData.lcdy < 16))//215 = TFT_XMAX - 24
{
GPIO_SetBits(GPIOC, (uint16_t)0xff & 0x00FF);
}
delay_ms(50000);
GPIO_SetBits(GPIOC, (uint16_t)0xff & 0x00FF);
TouchData.lcdx=0;
TouchData.lcdy=0;
}
}
else
{
if(g_ucTempbuf[0]==0x1A&&g_ucTempbuf[1]==0x46&&g_ucTempbuf[2]==0x95&&g_ucTempbuf[3]==0x1E)
{
// led1=0;
GUI_Show12Char(10,50,"开门 ",GREEN,BLACK); //开门
GUI_Show12Char(10,10,"姓名：二号 ",RED,BLACK);
// GPIO_SetBits(GPIOC, (uint16_t)0xff & 0x00FF);
if((TouchData.lcdx>50)&&(TouchData.lcdx<100))
{
if((TouchData.lcdy>280)&&(TouchData.lcdy<330))
{
GPIO_ResetBits(GPIOC, (~(uint16_t)0xfe) & 0x00FF);
delay_ms(50000);
TouchData.lcdx=0;
TouchData.lcdy=0;
// delay_ms(10);
// GPIO_SetBits(GPIOC, (uint16_t)0xfe& 0x00FF);
}
if((TouchData.lcdy>220)&&(TouchData.lcdy<270))
{
GPIO_ResetBits(GPIOC, (~(uint16_t)0xfd) & 0x00FF);
delay_ms(50000);
TouchData.lcdx=0;
TouchData.lcdy=0;
// delay_ms(10);
// GPIO_SetBits(GPIOC, (uint16_t)0xfd & 0x00FF);
}
if((TouchData.lcdy>120)&&(TouchData.lcdy<180))
{
GPIO_ResetBits(GPIOC, (~(uint16_t)0xfb) & 0x00FF);
delay_ms(50000);
TouchData.lcdx=0;
TouchData.lcdy=0;
// delay_ms(10);
// GPIO_SetBits(GPIOC, (uint16_t)0xfb & 0x00FF);
}
if ((TouchData.lcdx > TFT_XMAX-8*3) && (TouchData.lcdy < 16))//215 = TFT_XMAX - 24
{
GPIO_SetBits(GPIOC, (uint16_t)0xff & 0x00FF);
}
}
if ((TouchData.lcdx > TFT_XMAX-8*3) && (TouchData.lcdy < 16))//215 = TFT_XMAX - 24
{
GPIO_SetBits(GPIOC, (uint16_t)0xff & 0x00FF);
}
}
else
{
// led1=1;
GUI_Show12Char(10,50,"刷卡无法识别 ",RED,BLACK);
}}}}

复制代码