光立方制作资料下载带视频原理图源代码 8X8X8

ID:100539 · 发表于 2015-12-25 22:07

8X8X8光立方制作

8X8X8光立方原理图源程序制作教程等全部完整资料下载：

光立方2803 573.rar (2.67 MB, 下载次数: 84)

2015-12-26 00:08 上传

点击文件名下载附件

这是用573的电路，材料清单如下：

1：8个74HC573（封装为DIP—16）；

2：1个2803（封装为DIP—14）；

3：2个30PF的瓷介电容；一个10UF的电解电容；一个220UF的电解电容；

4：一块stc12a60s2（单片机）；

5：每个芯片配套的座子；

6：24或者12MHZ的晶振；

7： 1个1K，1个10K（都是碳膜电阻）；

8：一个按键开关，3个按键；

9：最好买600个灯，因为焊接的时候可能会损坏（颜色随便你自己选择）；

10：你可以考虑买4个铜柱；

备注：上面的3个按键可以只要1个，另外2个是我设计的外部中断，你可以不用它；同时我自己有开发板，所以我没有设计程序下载电路，全以最节省的方案为前提，你只要把单片机在开发板上下载好程序，再插到光立方上就好了。同时画电路时每个芯片的电源引脚隐藏了，（单片机是20接负，40接正；595是8接负，16接正；7404是7接负，14接正。），还有注意电解电容的极性。关于你接电源的问题是你自己的事，我是在板子上面安装了一个USB的接口供电。

以下是8X8X8光立方源程序代码：

#include <REG52.H>
#include <intrins.h>
#define uchar unsigned char
#define uint unsigned int
uchar display[8][8];
/*rank:A,1,2,3,4,I,心,U*/
uchar code table_cha[8][8]={0x51,0x51,0x51,0x4a,0x4a,0x4a,0x44,0x44,0x18,0x1c,0x18,0x18,0x18,0x18,0x18,0x3c,0x3c,0x66,0x66,0x30,0x18,0xc,0x6,0xf6,0x3c,0x66,0x60,0x38,0x60,0x60,0x66,0x3c,0x30,0x38,0x3c,0x3e,0x36,0x7e,0x30,0x30,0x3c,0x3c,0x18,0x18,0x18,0x18,0x3c,0x3c,0x66,0xff,0xff,0xff,0x7e,0x3c,0x18,0x18,0x66,0x66,0x66,0x66,0x66,0x66,0x7e,0x3c};
/*the "ideasoft"*/
uchar code table_id[40]={0x81,0xff,0x81,0x00,0xff,0x81,0x81,0x7e,0x00,0xff,0x89,0x89,0x00,0xf8,0x27,0x27,0xf8,0x00,0x8f,0x89,0x89,0xf9,0x00,0xff,0x81,0x81,0xff,0x00,0xff,0x09,0x09,0x09,0x01,0x0,0x01,0x01,0xff,0x01,0x01,0x00};
/*railway*/
uchar code dat[128]={0x0,0x20,0x40,0x60,0x80,0xa0,0xc0,0xe0,0xe4,0xe8,0xec,0xf0,0xf4,0xf8,0xfc,0xdc,0xbc,0x9c,0x7c,0x5c,0x3c,0x1c,0x18,0x14,0x10,0xc,0x8,0x4,0x25,0x45,0x65,0x85,0xa5,0xc5,0xc9,0xcd,0xd1,0xd5,0xd9,0xb9,0x99,0x79,0x59,0x39,0x35,0x31,0x2d,0x29,0x4a,0x6a,0x8a,0xaa,0xae,0xb2,0xb6,0x96,0x76,0x56,0x52,0x4e,0x6f,0x8f,0x93,0x73,0x6f,0x8f,0x93,0x73,0x4a,0x6a,0x8a,0xaa,0xae,0xb2,0xb6,0x96,0x76,0x56,0x52,0x4e,0x25,0x45,0x65,0x85,0xa5,0xc5,0xc9,0xcd,0xd1,0xd5,0xd9,0xb9,0x99,0x79,0x59,0x39,0x35,0x31,0x2d,0x29,0x0,0x20,0x40,0x60,0x80,0xa0,0xc0,0xe0,0xe4,0xe8,0xec,0xf0,0xf4,0xf8,0xfc,0xdc,0xbc,0x9c,0x7c,0x5c,0x3c,0x1c,0x18,0x14,0x10,0xc,0x8,0x4};
/*railway 2*/
uchar code dat2[28]={0x0,0x20,0x40,0x60,0x80,0xa0,0xc0,0xe0,0xe4,0xe8,0xec,0xf0,0xf4,0xf8,0xfc,0xdc,0xbc,0x9c,0x7c,0x5c,0x3c,0x1c,0x18,0x14,0x10,0xc,0x8,0x4};
/*railway 3*/
uchar code dat3[24]={0x00,0x01,0x02,0x03,0x04,0x05,0x06,0x16,0x26,0x36,0x46,0x56,0x66,0x65,0x64,0x63,0x62,0x61,0x60,0x50,0x40,0x30,0x20,0x10};
/*3p char*/
uchar code table_3p[3][8]={0xff,0x89,0xf5,0x93,0x93,0xf5,0x89,0xff,0x0e,0x1f,0x3f,0x7e,0x7e,0x3f,0x1f,0x0e,0x18,0x3c,0x7e,0xff,0x18,0x18,0x18,0x18};
/*initializtion
That is to initialize the program .
It is write to set the timer in c52 mcu.
So the program can renovate the led_3d_cube in fixed time use the interrupt function.*/
void sinter()
{
IE=0x82;
TCON=0x01;
TH0=0xc0;
TL0=0;
TR0=1;
}
void delay5us(void) //误差 -0.026765046296us STC 1T 22.1184Mhz
{
unsigned char a,b;
for(b=7;b>0;b--)
for(a=2;a>0;a--);
}
void delay(uint i)
{
while (i--){
delay5us();}//12t的mcu 注释这个延时即可
}
/*To judge the num bit*/
uchar judgebit(uchar num,uchar b)
{
char n;
num=num&(1<<b);
if (num)
n=1;
else
n=0;
return n;
}
/*To figure out the round number*/
uchar abs(uchar a)
{
uchar b;
b=a/10;
a=a-b*10;
if (a>=5)
b++;
return b;
}
/*To figure out the absolute value*/
uchar abss(char a)
{
if (a<0)
a=-a;
return a;
}
/*The function can comparat the character.
And remove the big one to the back.*/
void max(uchar *a,uchar *b)
{
uchar t;
if ((*a)>(*b))
{
t=(*a);
(*a)=(*b);
(*b)=t;
}
}
/*The function is to figure out the max number and return it.*/
uchar maxt(uchar a,uchar b,uchar c)
{
if (a<b)
a=b;
if (a<c)
a=c;
return a;
}
void clear(char le)
{
uchar i,j;
for (j=0;j<8;j++)
{
for (i=0;i<8;i++)
display[j][i]=le;
}
}
void trailler(uint speed)
{
char i,j;
for (i=6;i>=-3;i--)
{
if (i>=0)
{
for (j=0;j<8;j++)
display[j][i]=display[j][i+1];
}
if (i<4)
{
for (j=0;j<8;j++)
display[j][i+4]=0;
}
delay(speed);
}
}
void point(uchar x,uchar y,uchar z,uchar le)
{
uchar ch1,ch0;
ch1=1<<x;
ch0=~ch1;
if (le)
display[z][y]=display[z][y]|ch1;
else
display[z][y]=display[z][y]&ch0;
}
void type(uchar cha,uchar y)
{
uchar xx;
for (xx=0;xx<8;xx++)
{
display[xx][y]=table_cha[cha][xx];
}
}
/*The first variable is the distance from the midpoint.
The second is the layer.
the third is the flash speed of the time between each two point.
The forth is the enable io,it controls weather draw or claen.*/
void cirp(char cpp,uchar dir,uchar le)
{
uchar a,b,c,cp;
if ((cpp<128)&(cpp>=0))
{
if (dir)
cp=127-cpp;
else
cp=cpp;
a=(dat[cp]>>5)&0x07;
b=(dat[cp]>>2)&0x07;
c=dat[cp]&0x03;
if (cpp>63)
c=7-c;
point (a,b,c,le);
}
}
void line(uchar x1,uchar y1,uchar z1,uchar x2,uchar y2,uchar z2,uchar le)
{
char t,a,b,c,a1,b1,c1,i;
a1=x2-x1;
b1=y2-y1;
c1=z2-z1;
t=maxt(abss(a1),abss(b1),abss(c1));
a=x1*10;
b=y1*10;
c=z1*10;
a1=a1*10/t;
b1=b1*10/t;
c1=c1*10/t;
for (i=0;i<t;i++)
{
point(abs(a),abs(b),abs(c),le);
a+=a1;
b+=b1;
c+=c1;
}
point(x2,y2,z2,le);
}
void box(uchar x1,uchar y1,uchar z1,uchar x2,uchar y2,uchar z2,uchar fill,uchar le)
{
uchar i,j,t=0;
max(&x1,&x2);
max(&y1,&y2);
max(&z1,&z2);
for (i=x1;i<=x2;i++)
t|=1<<i;
if (!le)
t=~t;
if (fill)
{
if (le)
{
for (i=z1;i<=z2;i++)
{
for (j=y1;j<=y2;j++)
display[j][i]|=t;
}
}
else
{
for (i=z1;i<=z2;i++)
{
for (j=y1;j<=y2;j++)
display[j][i]&=t;
}
}
}
else
{
if (le)
{
display[y1][z1]|=t;
display[y2][z1]|=t;
display[y1][z2]|=t;
display[y2][z2]|=t;
}
else
{
display[y1][z1]&=t;
display[y2][z1]&=t;
display[y1][z2]&=t;
display[y2][z2]&=t;
}
t=(0x01<<x1)|(0x01<<x2);
if (!le)
t=~t;
if (le)
{
for (j=z1;j<=z2;j+=(z2-z1))
{
for (i=y1;i<=y2;i++)
display[i][j]|=t;
}
for (j=y1;j<=y2;j+=(y2-y1))
{
for (i=z1;i<=z2;i++)
display[j][i]|=t;
}
}
else
{
for (j=z1;j<=z2;j+=(z2-z1))
{
for (i=y1;i<=y2;i++)
{
display[i][j]&=t;
}
}
for (j=y1;j<=y2;j+=(y2-y1))
{
for (i=z1;i<=z2;i++)
{
display[j][i]&=t;
}
}
}
}
}
void box_apeak_xy(uchar x1,uchar y1,uchar z1,uchar x2,uchar y2,uchar z2,uchar fill,uchar le)
{
uchar i;
max(&z1,&z2);
if (fill)
{
for (i=z1;i<=z2;i++)
{
line (x1,y1,i,x2,y2,i,le);
}
}
else
{
line (x1,y1,z1,x2,y2,z1,le);
line (x1,y1,z2,x2,y2,z2,le);
line (x2,y2,z1,x2,y2,z2,le);
line (x1,y1,z1,x1,y1,z2,le);
}
}
void poke(uchar n,uchar x,uchar y)
{
uchar i;
for (i=0;i<8;i++)
{
point(x,y,i,judgebit(n,i));
}
}
void boxtola(char i,uchar n)
{
if ((i>=0)&(i<8))
{
poke(n,0,7-i);
}
if ((i>=8)&(i<16))
{
poke(n,i-8,0);
}
if ((i>=16)&(i<24))
{
poke(n,7,i-16);
}
}
void rolldisplay(uint speed)
{
uchar j;
char i,a;
for (i=23;i>-40;i--)
{
for (j=0;j<40;j++)
{
a=i+j;
if ((a>=0)&(a<24))
boxtola(a,table_id[j]);
}
delay(speed);
}
}
void roll_apeak_yz(uchar n,uint speed)
{
uchar i;
switch(n)
{
case 1:
for (i=0;i<7;i++)
{
display[i][7]=0;
display[7][6-i]=255;
delay(speed);
};
break;
case 2:
for (i=0;i<7;i++)
{
display[7][7-i]=0;
display[6-i][0]=255;
delay(speed);
};
break;
case 3:
for (i=0;i<7;i++)
{
display[7-i][0]=0;
display[0][i+1]=255;
delay(speed);
};
break;
case 0:
for (i=0;i<7;i++)
{
display[0][i]=0;
display[i+1][7]=255;
delay(speed);
};
}
}
void roll_apeak_xy(uchar n,uint speed)
{
uchar i;
switch(n)
{
case 1:
for (i=0;i<7;i++)
{
line(0,i,0,0,i,7,0);
line(i+1,7,0,i+1,7,7,1);
delay(speed);
};
break;
case 2:
for (i=0;i<7;i++)
{
line(i,7,0,i,7,7,0);
line(7,6-i,0,7,6-i,7,1);
delay(speed);
};
break;
case 3:
for (i=0;i<7;i++)
{
line(7,7-i,0,7,7-i,7,0);
line(6-i,0,0,6-i,0,7,1);
delay(speed);
};
break;
case 0:
for (i=0;i<7;i++)
{
line(7-i,0,0,7-i,0,7,0);
line(0,i+1,0,0,i+1,7,1);
delay(speed);
};
}
}
void roll_3_xy(uchar n,uint speed)
{
uchar i;
switch(n)
{
case 1:
for (i=0;i<8;i++)
{
box_apeak_xy (0,i,0,7,7-i,7,1,1);
delay(speed);
if (i<7)
box_apeak_xy (3,3,0,0,i,7,1,0);
};
break;
case 2:
for (i=0;i<8;i++)
{
box_apeak_xy (7-i,0,0,i,7,7,1,1);
delay(speed);
if (i<7)
box_apeak_xy (3,4,0,i,7,7,1,0);
};
break;
case 3:
for (i=0;i<8;i++)
{
box_apeak_xy (0,i,0,7,7-i,7,1,1);
delay(speed);
if (i<7)
box_apeak_xy (4,4,0,7,7-i,7,1,0);
};
break;
case 0:
for (i=0;i<8;i++)
{
box_apeak_xy (7-i,0,0,i,7,7,1,1);
delay(speed);
if (i<7)
box_apeak_xy (4,3,0,7-i,0,7,1,0);
};
}
}
void trans(uchar z,uint speed)
{
uchar i,j;
for (j=0;j<8;j++)
{
for (i=0;i<8;i++)
{
display[z][i]>>=1;
}
delay(speed);
}
}
void tranoutchar(uchar c,uint speed)
{
uchar i,j,k,a,i2=0;
for (i=0;i<8;i++)
{
if (i<7)
box_apeak_xy (i+1,0,0,i+1,7,7,1,1);
box_apeak_xy (i2,0,0,i2,7,7,1,0);
a=0;
i2=i+1;
for (j=0;j<=i;j++)
{
a=a|(1<<j);
}
for (k=0;k<8;k++)
{
display[k][3]|=table_cha[c][k]&a;
display[k][4]|=table_cha[c][k]&a;
}
delay(speed);
}
}
void transss()
{
uchar i,j;
for (i=0;i<8;i++)
{
for (j=0;j<8;j++)
display[i][j]<<=1;
}
}
/*From now on,the function below is to display the flash.*/
void flash_1()
{
clear(0);
type(1,0);
delay(60000);
type(2,0);
delay(60000);
type(3,0);
delay(60000);
type(4,0);
delay(60000);
delay(60000);
clear(0);
rolldisplay(30000);
type(0,7);
delay(60000);
trailler(6000);
delay(60000);
}
void flash_2()
{
uchar i;
for (i=129;i>0;i--)
{
cirp(i-2,0,1);
delay(8000);
cirp(i-1,0,0);
}
delay(8000);
for (i=0;i<136;i++)
{
cirp(i,1,1);
delay(8000);
cirp(i-8,1,0);
}
delay(8000);
for (i=129;i>0;i--)
{
cirp(i-2,0,1);
delay(8000);
}
delay(8000);
for (i=0;i<128;i++)
{
cirp(i-8,1,0);
delay(8000);
}
delay(60000);
}
void flash_3()
{
char i;
for (i=0;i<8;i++)
{
box_apeak_xy(0,i,0,7,i,7,1,1);
delay(20000);
if (i<7)
box_apeak_xy(0,i,0,7,i,7,1,0);
}
for (i=7;i>=0;i--)
{
box_apeak_xy(0,i,0,7,i,7,1,1);
delay(20000);
if (i>0)
box_apeak_xy(0,i,0,7,i,7,1,0);
}
for (i=0;i<8;i++)
{
box_apeak_xy(0,i,0,7,i,7,1,1);
delay(20000);
if (i<7)
box_apeak_xy(0,i,0,7,i,7,1,0);
}
}
void flash_4()
{
char i,j,an[8];
for (j=7;j<15;j++)
an[j-7]=j;
for (i=0;i<=16;i++)
{
for (j=0;j<8;j++)
{
if ((an[j]<8)&(an[j]>=0))
line(0,an[j],j,7,an[j],j,1);
}
for (j=0;j<8;j++)
{
if (((an[j]+1)<8)&(an[j]>=0))
line(0,an[j]+1,j,7,an[j]+1,j,0);
}
for (j=0;j<8;j++)
{
if (an[j]>0)
an[j]--;
}
delay(15000);
}
for (j=0;j<8;j++)
an[j]=1-j;
for (i=0;i<=16;i++)
{
for (j=0;j<8;j++)
{
if ((an[j]<8)&(an[j]>=0))
line(0,an[j],j,7,an[j],j,1);
}
for (j=0;j<8;j++)
{
if (((an[j]-1)<7)&(an[j]>0))
line(0,an[j]-1,j,7,an[j]-1,j,0);
}
for (j=0;j<8;j++)
{
if (an[j]<7)
an[j]++;
}
delay(15000);
}
}
void flash_5()
{
uint a=15000;//a=delay
char i=8,j,an[4];
//1
for (j=7;j<11;j++)
an[j-7]=j;
while(i--)
{
for (j=0;j<4;j++)
{
if (an[j]<8)
box_apeak_xy(j,an[j],j,7-j,an[j],7-j,0,1);
if (an[j]<7)
box_apeak_xy(j,an[j]+1,j,7-j,an[j]+1,7-j,0,0);
}
for (j=0;j<4;j++)
{
if (an[j]>3)
an[j]--;
}
delay(a);
}
//2
i=3;
for (j=0;j<4;j++)
an[j]=5-j;
while(i--)
{
for (j=1;j<4;j++)
{
if (an[j]<4)
box_apeak_xy(j,an[j],j,7-j,an[j],7-j,0,1);
if (an[j]<3)
box_apeak_xy(j,an[j]+1,j,7-j,an[j]+1,7-j,0,0);
}
for (j=0;j<4;j++)
{
if (an[j]>0)
an[j]--;
}
delay(a);
}
//3
i=3;
for (j=1;j<4;j++)
an[j]=4-j;
while(i--)
{
for (j=1;j<4;j++)
{
if (an[j]>=0)
box_apeak_xy(j,an[j],j,7-j,an[j],7-j,0,1);
if (an[j]>0)
box_apeak_xy(j,an[j]-1,j,7-j,an[j]-1,7-j,0,0);
}
for (j=1;j<4;j++)
{
if (an[j]<3)
an[j]++;
}
delay(a);
}
//4
i=3;
for (j=0;j<4;j++)
an[j]=j+1;
while(i--)
{
for (j=1;j<4;j++)
{
if (an[j]>3)
box_apeak_xy(j,an[j],j,7-j,an[j],7-j,0,1);
if (an[j]>3)
box_apeak_xy(j,an[j]-1,j,7-j,an[j]-1,7-j,0,0);
}
for (j=0;j<4;j++)
an[j]++;
delay(a);
}
//5
i=3;
for (j=3;j<6;j++)
an[j-2]=j;
while(i--)
{
for (j=1;j<4;j++)
{
box_apeak_xy(j,an[j],j,7-j,an[j],7-j,0,1);
box_apeak_xy(j,an[j]+1,j,7-j,an[j]+1,7-j,0,0);
}
for (j=0;j<4;j++)
{
if (an[j]>3)
an[j]--;
}
delay(a);
}
//6
i=3;
for (j=0;j<4;j++)
an[j]=5-j;
while(i--)
{
for (j=1;j<4;j++)
{
if (an[j]<4)
box_apeak_xy(j,an[j],j,7-j,an[j],7-j,0,1);
if (an[j]<3)
box_apeak_xy(j,an[j]+1,j,7-j,an[j]+1,7-j,0,0);
}
for (j=0;j<4;j++)
{
if (an[j]>0)
an[j]--;
}
delay(a);
}
//7
i=3;
for (j=0;j<4;j++)
an[j]=3-j;
an[0]=2;
while(i--)
{
for (j=0;j<3;j++)
{
if (an[j]>=0)
box_apeak_xy(j,an[j],j,7-j,an[j],7-j,0,1);
if (an[j]>=0)
box_apeak_xy(j,an[j]+1,j,7-j,an[j]+1,7-j,0,0);
}
for (j=0;j<4;j++)
{
if (j<5-i)
an[j]--;
}
delay(a);
}
//8
i=10;
for (j=0;j<4;j++)
an[j]=j-2;
while(i--)
{
for (j=0;j<4;j++)
{
if (an[j]>=0)
box_apeak_xy(j,an[j],j,7-j,an[j],7-j,0,1);
if (an[j]>=0)
box_apeak_xy(j,an[j]-1,j,7-j,an[j]-1,7-j,0,0);
}
for (j=0;j<4;j++)
{
if (an[j]<7)
an[j]++;
}
delay(a);
}
}
void flash_6()
{
uchar i,j,k,z;
roll_apeak_yz(1,10000);
roll_apeak_yz(2,10000);
roll_apeak_yz(3,10000);
roll_apeak_yz(0,10000);
roll_apeak_yz(1,10000);
roll_apeak_yz(2,10000);
roll_apeak_yz(3,10000);
for (i=0;i<3;i++)
{
for (j=0;j<8;j++)
{
for (k=0;k<8;k++)
{
if ((table_3p[i][j]>>k)&1)
{
for (z=1;z<8;z++)
{
point (j,7-k,z,1);
if (z-1)
point (j,7-k,z-1,0);
delay(5000);
}
}
}
}
trans(7,15000);
}
}
void flash_7()
{
uchar i;
uint a=3000;
roll_apeak_yz(0,10000);
roll_apeak_yz(1,10000);
roll_apeak_yz(2,10000);
roll_apeak_yz(3,10000);
roll_apeak_yz(0,10000);
roll_apeak_yz(1,10000);
roll_apeak_yz(2,10000);
roll_apeak_yz(3,10000);
roll_apeak_yz(0,10000);
roll_apeak_yz(1,10000);
roll_apeak_yz(2,10000);
roll_apeak_xy(0,10000);
roll_apeak_xy(1,10000);
roll_apeak_xy(2,10000);
roll_apeak_xy(3,10000);
roll_apeak_xy(0,10000);
roll_apeak_xy(1,10000);
roll_apeak_xy(2,10000);
roll_apeak_xy(3,10000);
for (i=0;i<8;i++)
{
box_apeak_xy (0,i,0,7-i,i,7,1,1);
delay(a);
}
delay(30000);
roll_3_xy(0,a);
delay(30000);
roll_3_xy(1,a);
delay(30000);
roll_3_xy(2,a);
delay(30000);
roll_3_xy(3,a);
delay(30000);
roll_3_xy(0,a);
delay(30000);
roll_3_xy(1,a);
delay(30000);
roll_3_xy(2,a);
delay(30000);
roll_3_xy(3,a);
for (i=7;i>0;i--)
{
box_apeak_xy(i,0,0,i,7,7,1,0);
delay(a);
}
}
void flash_8()
{
uchar i;
for (i=5;i<8;i++)
{
tranoutchar(i,10000);
delay(60000);
delay(60000);
}
}
void flash_9()
{
char i;
uchar j,an[8],x,y,t,x1,y1;
for (i=0;i<8;i++)
{
box_apeak_xy (i,0,0,i,7,7,1,1);
if (i)
box_apeak_xy (i-1,0,0,i-1,7,7,1,0);
delay(10000);
}
roll_apeak_xy(3,10000);
roll_apeak_xy(0,10000);
roll_apeak_xy(1,10000);
for (i=0;i<7;i++)
{
line(6-i,6-i,0,6-i,6-i,7,1);
line(i,7,0,i,7,7,0);
delay(10000);
}
for (i=0;i<8;i++)
an[i]=14;
for (i=0;i<85;i++)
{
clear(0);
for (j=0;j<8;j++)
{
t=an[j]%28;
x=dat2[t]>>5;
y=(dat2[t]>>2)&0x07;
t=(an[j]-14)%28;
x1=dat2[t]>>5;
y1=(dat2[t]>>2)&0x07;
line(x,y,j,x1,y1,j,1);
}
for (j=0;j<8;j++)
{
if ((i>j)&(j>i-71))
an[j]++;
}
delay(5000);
}
for (i=0;i<85;i++)
{
clear(0);
for (j=0;j<8;j++)
{
t=an[j]%28;
x=dat2[t]>>5;
y=(dat2[t]>>2)&0x07;
t=(an[j]-14)%28;
x1=dat2[t]>>5;
y1=(dat2[t]>>2)&0x07;
line(x,y,j,x1,y1,j,1);
}
for (j=0;j<8;j++)
{
if ((i>j)&(j>i-71))
an[j]--;
}
delay(5000);
}
for (i=0;i<29;i++)
{
clear(0);
t=an[0]%28;
x=dat2[t]>>5;
y=(dat2[t]>>2)&0x07;
t=(an[0]-14)%28;
x1=dat2[t]>>5;
y1=(dat2[t]>>2)&0x07;
box_apeak_xy(x,y,0,x1,y1,7,0,1);
box_apeak_xy(x,y,1,x1,y1,6,0,1);
an[0]++;
delay(5000);
}
for (i=0;i<16;i++)
{
clear(0);
t=an[0]%28;
x=dat2[t]>>5;
y=(dat2[t]>>2)&0x07;
t=(an[0]-14)%28;
x1=dat2[t]>>5;
y1=(dat2[t]>>2)&0x07;
box_apeak_xy(x,y,0,x1,y1,7,1,1);
an[0]--;
delay(5000);
}
for (i=0;i<8;i++)
{
line(i,i,0,0,0,i,0);
delay(5000);
}
for (i=1;i<7;i++)
{
line(i,i,7,7,7,i,0);
delay(5000);
}
for (i=1;i<8;i++)
{
clear(0);
box(7,7,7,7-i,7-i,7-i,0,1);
delay(10000);
}
for (i=1;i<7;i++)
{
clear(0);
box(0,0,0,7-i,7-i,7-i,0,1);
delay(10000);
}
for (i=1;i<8;i++)
{
clear(0);
box(0,0,0,i,i,i,0,1);
delay(10000);
}
for (i=1;i<7;i++)
{
clear(0);
box(7,0,0,i,7-i,7-i,0,1);
delay(10000);
}
for (i=1;i<8;i++)
{
box(7,0,0,7-i,i,i,1,1);
delay(10000);
}
for (i=1;i<7;i++)
{
clear(0);
box(0,7,7,7-i,i,i,1,1);
delay(10000);
}
}
void flash_10()
{
uchar i,j,an[4],x,y,t;
for (i=1;i<7;i++)
{
clear(0);
box(0,6,6,1,7,7,1,1);
box(i,6,6-i,i+1,7,7-i,1,1);
box(i,6,6,i+1,7,7,1,1);
box(0,6,6-i,1,7,7-i,1,1);
box(0,6-i,6,1,7-i,7,1,1);
box(i,6-i,6-i,i+1,7-i,7-i,1,1);
box(i,6-i,6,i+1,7-i,7,1,1);
box(0,6-i,6-i,1,7-i,7-i,1,1);
delay(30000);
}
for (i=0;i<4;i++)
{
an[i]=6*i;
}
for (i=0;i<35;i++)
{
clear(0);
for(j=0;j<4;j++)
{
t=an[j]%24;
x=dat3[t]>>4;
y=dat3[t]&0x0f;
box(x,y,0,x+1,y+1,1,1,1);
box(x,y,6,x+1,y+1,7,1,1);
}
for (j=0;j<4;j++)
an[j]++;
delay(10000);
}
for (i=0;i<35;i++)
{
clear(0);
for(j=0;j<4;j++)
{
t=an[j]%24;
x=dat3[t]>>4;
y=dat3[t]&0x0f;
box(x,y,0,x+1,y+1,1,1,1);
box(x,y,6,x+1,y+1,7,1,1);
}
for (j=0;j<4;j++)
an[j]--;
delay(10000);
}
for (i=0;i<35;i++)
{
clear(0);
for(j=0;j<4;j++)
{
t=an[j]%24;
x=dat3[t]>>4;
y=dat3[t]&0x0f;
box(x,0,y,x+1,1,y+1,1,1);
box(x,6,y,x+1,7,y+1,1,1);
}
for (j=0;j<4;j++)
an[j]++;
delay(10000);
}
for (i=0;i<36;i++)
{
clear(0);
for(j=0;j<4;j++)
{
t=an[j]%24;
x=dat3[t]>>4;
y=dat3[t]&0x0f;
box(x,0,y,x+1,1,y+1,1,1);
box(x,6,y,x+1,7,y+1,1,1);
}
for (j=0;j<4;j++)
an[j]--;
delay(10000);
}
for (i=6;i>0;i--)
{
clear(0);
box(0,6,6,1,7,7,1,1);
box(i,6,6-i,i+1,7,7-i,1,1);
box(i,6,6,i+1,7,7,1,1);
box(0,6,6-i,1,7,7-i,1,1);
box(0,6-i,6,1,7-i,7,1,1);
box(i,6-i,6-i,i+1,7-i,7-i,1,1);
box(i,6-i,6,i+1,7-i,7,1,1);
box(0,6-i,6-i,1,7-i,7-i,1,1);
delay(30000);
}
}
void flash_11()
{
uchar i,j,t,x,y;
uchar code daa[13]={0,1,2,0x23,5,6,7,6,5,0x23,2,1,0};
for (j=0;j<5;j++)
{
for (i=0;i<13;i++)
{
if (daa[i]>>4)
{
t=daa[i]&0x0f;
line (0,0,t+1,0,7,t+1,1);
}
else
t=daa[i];
line (0,0,t,0,7,t,1);
transss();
delay(10000);
}
}
for (j=1;j<8;j++)
{
if (j>3)
t=4;
else
t=j;
for (i=0;i<24;i+=j)
{
x=dat3[i]>>4;
y=dat3[i]&0x0f;
box_apeak_xy(0,x,y,0,x+1,y+1,1,1);
transss();
delay(10000);
}
}
for (j=1;j<8;j++)
{
if (j>3)
t=4;
else
t=j;
for (i=0;i<24;i+=j)
{
x=dat3[i]>>4;
y=dat3[i]&0x0f;
point (0,x,y,1);
transss();
delay(10000);
}
}
}
void main()
{
sinter();
while(1){
// clear(0);
/*play list*/
//flash_1();
clear(0);
flash_2();
flash_3();
flash_4();
flash_4();
flash_5();
flash_5();
flash_6();
flash_7();
flash_8();
flash_9();
flash_10();
clear (0);
flash_11();
flash_9();
flash_5();
flash_7();
flash_5();
flash_6();
flash_8();
flash_9();
flash_10();
}
}
//P0; //573 in
//P1; //uln2803
//P2; //573 LE
void print() interrupt 1
{
uchar i;
static uchar layer=0;
P1=0;
for (i=0;i<8;i++)
{
P2=1<<i;
delay(3);
P0=display[layer][i];
delay(3);
}
P1=1<<layer;
if (layer<7)
layer++;
else
layer=0;
TH0=0xc0;
TL0=0;
}

复制代码

ID:85607 · 发表于 2016-2-24 14:26

MARK 留着备用~ 多谢分享

ID:105494 · 发表于 2016-2-24 23:54

问下你限流电阻焊哪了？？

ID:174226 · 发表于 2017-3-20 11:41

谢谢楼主

ID:248495 · 发表于 2017-11-11 22:45

好像做一个啊，好漂亮

ID:319663 · 发表于 2018-5-1 01:14

很想要来做一个

ID:317390 · 发表于 2018-5-4 14:56

好漂亮的光立方！谢谢分享~

帐号		自动登录	找回密码
密码			立即注册

光立方制作资料下载带视频原理图源代码 8X8X8

评分

相关帖子

光立方制作资料下载 带视频 原理图 源代码 8X8X8

评分

相关帖子

光立方制作资料下载带视频原理图源代码 8X8X8