单片机点阵时钟原理图和源码

ID:249790 · 发表于 2017-11-15 19:13

这是单片机点阵时钟的程序和proteus图，欢迎大家指正

原理图大家执行解压后用protel99打开.

单片机源程序如下:

//LED点阵时钟程序
//作者：刘宁
//--------------------------------
#include "reg52.h"
#define uchar unsigned char
#define uint unsigned int
//========================
//****滚屏事件定义****
#define MSG_MV_L 1 //左移
#define MSG_MV_R 2 //右移
#define MSG_MV_U 3 //上移
#define MSG_MV_D 4 //下移
#define MSG_NONE 0 //无
uchar MSG_MV = 0;
//========================
//****显示状态定义****
#define STA_gTIME 1 //滚动显示时间
#define STA_gTEMP 2 //滚动显示温度
#define STA_gWORD 3 //滚动显示文字
#define STA_sTIME 4 //静态显示时间
#define STA_sWEEK 5 //静态显示星期
#define STA_sDATE 6 //静态显示日期
#define STA_sYEAR 7 //静态显示年份
#define STA_sTEMP 8 //静态显示温度
#define STA_sWORD 9 //静态显示文字
#define STA_CHG 10 //校时模式
#define STA_SONG 11 //滚动显示诗歌
#define STA_COPYRIGHT 12 //开机显示
uchar STATE = 1;
//=========================
//****校时状态定义****
#define CHG_HOUR 1 //调整小时
#define CHG_MIN 2 //调整分
#define CHG_SEC 3 //调整秒
#define CHG_MON 4 //调整月
#define CHG_DAY 5 //调整日
#define CHG_WEEK 6 //调整星期
#define CHG_YEAR 7 //调整年
uchar CHANGE = 1;
uchar hide_times = 0; //校时闪烁时间变量
uchar HIDE = 0; //隐藏显示标志位
uchar TMP_TIME = 0;
//=========================
//****按键定义****
sbit key0 = P1^0;
sbit key1 = P1^1;
sbit key2 = P1^2;
sbit key3 = P1^3;
#define KEY0 0x0e
#define KEY1 0x0d
#define KEY2 0x0b
#define KEY3 0x07
#define KEY0_S 0x0e //KEY0短按下
#define KEY1_S 0x0d //KEY1短按下
#define KEY2_S 0x0b //KEY2短按下
#define KEY3_S 0x07 //KEY3短按下
#define KEY0_L 0x1e //KEY0长按下
#define KEY1_L 0x1d //KEY1长按下
#define KEY2_L 0x1b //KEY2长按下
#define KEY3_L 0x17 //KEY3长按下
#define KEY_NONE 0 //无按键
uchar MSG_KEY = KEY_NONE;
uchar key_times = 0; //持续时间
uchar key_keep_times = 0;
uchar cur_key_val = 0;
uchar key_done = 0; //按键事件有无做好
uchar exit = 0; //校时状态下长时间无按键退出
//=========================
//uchar time_read_times = 0; //读时间
//uchar tem_read_times = 0; //读温度
//=========================
//****引脚定义****
sbit CLK =P2^5 ; //74HC595移时钟
sbit STB =P2^4 ; // 74HC595锁存信号
sbit Red=P2^7 ; //红色数据输出引脚低电平有效
sbit Greed=P2^6; //全屏控制使能0，低电平有效
sbit OE = P0^7; //全屏使能
//========================
//****DS1302****
sbit SCLK=P0^4; //位定义1302芯片的接口，时钟输出端口定义在P2.4引脚
sbit DATA=P0^5; //位定义1302芯片的接口，数据输出端定义在P2.5引脚
sbit RST=P0^6; //位定义1302芯片的接口，复位端口定义在P2.6引脚
typedef struct __SYSTEMTIME__
{
uchar Second;
uchar Minute;
uchar Hour;
uchar Day;
uchar Month;
uchar Week;
uchar Year;
}SYSTEMTIME; //定义的时间类型
SYSTEMTIME Time;
//=========================================
//****18B20****
sbit DQ = P0^7
; //定义DS18B20端口DQ
unsigned char data temp_data[2] = {0x00,0x00} ;
unsigned char data temp_ram[5] = {0x00,0x00,0x00,0x00,0x00} ;
unsigned char code ditab[16] = {0x00,0x01,0x01,0x02,0x03,0x03,0x04,0x04,
0x05,0x06,0x06,0x07,0x08,0x08,0x09,0x09};
//==========================================
bit presence ;
uchar SendData; //要发送的数据变量
uchar hang; //行扫描变量（半屏只有16行，所以hang=0到15）
uchar move_times = 0; //左右移动位数
uchar start_word = 0;
uchar data h_dispram[10]; //显示缓存
uchar code *disword[26]; //显示文字指针
void Keyscan (void); //修改参数按键扫描子程序
void Sendping(); //发送半屏子程序
void Put_Wdispram(uchar first_word);//
void Put_Hdispram(); //把显示文字放入显示缓存
void Move_Left(); //左移
void Move_Right(); //右移
void RL_Move();
void UD_Move();
void Show_Line();
void Show_Move_Word(uchar code *WORDS[][8]);
void delay();
void SendByte(void);
void RowsCan(void);
void Disp_Temperature();
void Put_gTEMP();
void Change_obj();
uchar ReadKey1();
uchar code MY_WORDS[][16]=
{
{0x10,0x08,0x04,0x7F,0x01,0x21,0x12,0x0A,0x04,0x06,0x0A,0x11,0x21,0x41,0x80,0x00},
{0x04,0x04,0x04,0xA4,0x24,0x24,0x24,0x24,0x24,0x24,0x24,0x04,0x84,0x14,0x08,0x00},/*"刘",0*/
{0x02,0x01,0x3F,0x20,0x40,0x00,0x00,0x7F,0x01,0x01,0x01,0x01,0x01,0x01,0x05,0x02},
{0x00,0x04,0xFE,0x04,0x08,0x00,0x00,0xFC,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"宁",1*/
{0x01,0x01,0x01,0x01,0x01,0x1F,0x10,0x10,0x10,0x1F,0x10,0x01,0x28,0x24,0x44,0x00},
{0x00,0x00,0xF8,0x00,0x10,0xF8,0x10,0x10,0x10,0xF0,0x10,0x10,0x88,0x44,0x44,0x00},/*"点",2*/
{0x00,0xF8,0x88,0x97,0xA1,0x91,0x8A,0x8F,0x88,0xA8,0x97,0x80,0x80,0x80,0x80,0x80},
{0x80,0x80,0x80,0xFC,0x00,0x40,0x40,0xFC,0x40,0x40,0xFE,0x40,0x40,0x40,0x40,0x40},/*"阵",3*/
{0x00,0x00,0x3F,0x00,0x00,0x00,0xFF,0x03,0x07,0x06,0x0C,0x18,0x31,0x7F,0x20,0x00},
{0x00,0x30,0xF8,0x00,0x00,0x0C,0xFE,0x00,0x00,0x40,0x20,0x10,0xF8,0x0C,0x08,0x00},/*"云",0*/
{0x01,0x01,0xFF,0x01,0x02,0x3F,0x24,0x22,0x2F,0x21,0x3F,0x21,0x21,0x21,0x21,0x00},
{0x00,0x04,0xFE,0x00,0x00,0xFC,0x24,0x44,0xF4,0x04,0xFC,0x04,0x04,0x14,0x08,0x00},/*"南",1*/
{0x02,0x02,0x04,0x3F,0x20,0x20,0x20,0x20,0x3F,0x20,0x20,0x20,0x20,0x3F,0x20,0x00},
{0x00,0x00,0x00,0xF8,0x08,0x08,0x08,0x08,0xF8,0x08,0x08,0x08,0x08,0xF8,0x08,0x00},/*"白",2*/
{0x04,0x04,0x7F,0x04,0x14,0x10,0x24,0x7C,0x09,0x10,0x7E,0x20,0x06,0x78,0x20,0x00},
{0x40,0x40,0xFE,0x40,0x40,0x40,0x7C,0x84,0x04,0x44,0x24,0x24,0x04,0x04,0x28,0x10},/*"药",3*/
{0x08,0x08,0x1F,0x10,0x20,0x4F,0x00,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},
};
uchar code NO_WORDS[][16]={
{0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x24,0x18,0x00,0x00},/*"0",0*/
{0x00,0x00,0x00,0x10,0x70,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x7C,0x00,0x00},/*"1",1*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x04,0x04,0x08,0x10,0x20,0x42,0x7E,0x00,0x00},/*"2",2*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x04,0x18,0x04,0x02,0x02,0x42,0x44,0x38,0x00,0x00},/*"3",3*/
{0x00,0x00,0x00,0x04,0x0C,0x14,0x24,0x24,0x44,0x44,0x7E,0x04,0x04,0x1E,0x00,0x00},/*"4",4*/
{0x00,0x00,0x00,0x7E,0x40,0x40,0x40,0x58,0x64,0x02,0x02,0x42,0x44,0x38,0x00,0x00},/*"5",5*/
{0x00,0x00,0x00,0x1C,0x24,0x40,0x40,0x58,0x64,0x42,0x42,0x42,0x24,0x18,0x00,0x00},/*"6",6*/
{0x00,0x00,0x00,0x7E,0x44,0x44,0x08,0x08,0x10,0x10,0x10,0x10,0x10,0x10,0x00,0x00},/*"7",7*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x24,0x18,0x24,0x42,0x42,0x42,0x3C,0x00,0x00},/*"8",8*/
{0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x26,0x1A,0x02,0x02,0x24,0x38,0x00,0x00},/*"9",9*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"-",10*/
{0x00,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00},/*":",11*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"空格",12*/
};
uchar code TMP_WORDS[][16]={
{0x02,0x01,0x3F,0x20,0x40,0x3F,0x04,0x08,0x1F,0x01,0x01,0x3F,0x01,0x01,0xFF,0x00},
{0x00,0x00,0xFE,0x04,0x08,0xFC,0x00,0x20,0xF0,0x10,0x00,0xF8,0x00,0x00,0xFE,0x00},/*"室",3*/
{0x40,0x27,0x24,0x07,0x94,0x54,0x17,0x20,0x2F,0xC9,0x49,0x49,0x49,0x49,0x5F,0x40},
{0x00,0xF0,0x10,0xF0,0x10,0x10,0xF0,0x00,0xFC,0x24,0x24,0x24,0x24,0x24,0xFE,0x00},/*"温",4*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00},/*":",5*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",6*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",8*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x60,0x00,0x00},/*".",9*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",10*/
{0x00,0xC0,0xC0,0x3E,0x42,0x42,0x80,0x80,0x80,0x80,0x80,0x42,0x44,0x38,0x00,0x00},/*"C",11*/
};
uchar code TIME_WORDS[][16]={
{0x01,0x01,0x02,0x04,0x08,0x12,0x21,0xC0,0x00,0x1F,0x00,0x00,0x00,0x00,0x00,0x01},
{0x00,0x00,0x80,0x40,0x20,0x18,0x8E,0x84,0x00,0xF0,0x20,0x20,0x40,0x40,0x80,0x00},/*"今",0*/
{0x00,0x3F,0x01,0x01,0x01,0x01,0x7F,0x01,0x01,0x02,0x02,0x04,0x08,0x10,0x20,0x40},
{0x00,0xFC,0x00,0x00,0x00,0x00,0xFE,0x00,0x00,0x80,0x40,0x20,0x18,0x0E,0x04,0x00},/*"天",1*/
{0x00,0x0F,0x08,0x0F,0x08,0x0F,0x00,0xFF,0x01,0x09,0x09,0x09,0x15,0x23,0x40,0x00},
{0x00,0xF0,0x10,0xF0,0x10,0xF0,0x00,0xFE,0x00,0x00,0xF8,0x00,0x00,0x00,0xFE,0x00},/*"是",2*/
{0x08,0x0F,0x10,0x10,0x20,0x4F,0x88,0x08,0x08,0x08,0xFF,0x00,0x00,0x00,0x00,0x00},
{0x00,0xFC,0x80,0x80,0x80,0xF8,0x80,0x80,0x80,0x80,0xFE,0x80,0x80,0x80,0x80,0x80},/*"年",1*/
{0x07,0x04,0x04,0x04,0x07,0x04,0x04,0x04,0x07,0x04,0x08,0x08,0x10,0x20,0x40,0x00},
{0xF0,0x10,0x10,0x10,0xF0,0x10,0x10,0x10,0xF0,0x10,0x10,0x10,0x10,0x50,0x20,0x00},/*"月",2*/
{0x00,0x1F,0x10,0x10,0x10,0x10,0x1F,0x10,0x10,0x10,0x10,0x10,0x1F,0x10,0x00,0x00},
{0x00,0xF0,0x10,0x10,0x10,0x10,0xF0,0x10,0x10,0x10,0x10,0x10,0xF0,0x10,0x00,0x00},/*"日",3*/
{0x00,0x1F,0x10,0x1F,0x10,0x1F,0x01,0x11,0x1F,0x21,0x21,0x4F,0x01,0x01,0x7F,0x00},
{0x00,0xF8,0x08,0xF8,0x08,0xF8,0x00,0x00,0xFC,0x00,0x00,0xF8,0x00,0x00,0xFE,0x00},/*"星",4*/
{0x22,0x22,0x7F,0x22,0x3E,0x22,0x3E,0x22,0x22,0xFF,0x00,0x24,0x22,0x43,0x81,0x00},
{0x00,0x7C,0x44,0x44,0x44,0x7C,0x44,0x44,0x44,0x7C,0x44,0x84,0x84,0x14,0x08,0x00},/*"期",5*/
};
uchar code WEEK_WORDS[][16]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},
{0x00,0x00,0x00,0x00,0x00,0x00,0x04,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"一",0*/
{0x00,0x00,0x3F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x00,0x00},
{0x00,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0xFE,0x00,0x00,0x00},/*"二",1*/
{0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x00},
{0x00,0x00,0xFC,0x00,0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0xFE,0x00,0x00},/*"三",2*/
{0x00,0x7F,0x44,0x44,0x44,0x44,0x44,0x44,0x48,0x48,0x50,0x60,0x40,0x7F,0x40,0x00},
{0x00,0xFC,0x84,0x84,0x84,0x84,0x84,0x84,0x84,0x7C,0x04,0x04,0x04,0xFC,0x04,0x00},/*"四",3*/
{0x00,0x7F,0x02,0x02,0x02,0x02,0x02,0x3F,0x04,0x04,0x04,0x04,0x04,0xFF,0x00,0x00},
{0x00,0xF8,0x00,0x00,0x00,0x00,0x20,0xF0,0x20,0x20,0x20,0x20,0x24,0xFE,0x00,0x00},/*"五",4*/
{0x04,0x03,0x01,0x01,0xFF,0x00,0x00,0x04,0x06,0x04,0x08,0x08,0x10,0x20,0x40,0x00},
{0x00,0x00,0x80,0x00,0xFE,0x00,0x00,0x80,0x40,0x20,0x10,0x18,0x0C,0x0C,0x08,0x00},/*"六",5*/
{0x00,0x1F,0x10,0x10,0x10,0x10,0x1F,0x10,0x10,0x10,0x10,0x10,0x1F,0x10,0x00,0x00},
{0x00,0xF0,0x10,0x10,0x10,0x10,0xF0,0x10,0x10,0x10,0x10,0x10,0xF0,0x10,0x00,0x00},/*"日",0*/
};
uchar code SONG_WORDS[][16] = {
{0x00,0x08,0x04,0x04,0x00,0x0F,0x01,0x01,0x7F,0x01,0x02,0x04,0x08,0x30,0x00,0x00},
{0x40,0x40,0x40,0x80,0xE0,0x00,0x00,0xF8,0x00,0x00,0x80,0x40,0x30,0x1C,0x00,0x00},/*"关",0*/
{0x00,0x08,0x04,0x04,0x00,0x0F,0x01,0x01,0x7F,0x01,0x02,0x04,0x08,0x30,0x00,0x00},
{0x40,0x40,0x40,0x80,0xE0,0x00,0x00,0xF8,0x00,0x00,0x80,0x40,0x30,0x1C,0x00,0x00},/*"关",1*/
{0x00,0x00,0x18,0x68,0x49,0x6B,0x4D,0x69,0x49,0x4D,0x71,0xC1,0x01,0x01,0x01,0x00},
{0x40,0x40,0xA0,0x90,0x1C,0x70,0x1C,0x70,0x1C,0x70,0x10,0x1E,0x60,0x00,0x00,0x00},/*"雎",2*/
{0x00,0x00,0x10,0x11,0x1D,0x75,0x15,0x15,0x17,0x25,0x24,0x40,0x87,0x00,0x00,0x00},
{0x40,0x40,0xF0,0x10,0x50,0x10,0x70,0x00,0x1C,0xE4,0x04,0xF4,0x04,0x14,0x08,0x00},/*"鸠",3*/
{0x01,0x01,0x01,0x01,0x1E,0x04,0x04,0x08,0x18,0x2B,0x48,0x88,0x0F,0x08,0x08,0x00},
{0x00,0x00,0x00,0xF0,0x00,0x40,0x40,0x40,0x70,0xC0,0x40,0x7C,0x80,0x00,0x00,0x00},/*"在",4*/
{0x00,0x10,0x08,0x07,0x40,0x21,0x06,0x04,0x13,0x10,0x20,0x20,0x20,0x00,0x00,0x00},
{0x00,0x00,0x1E,0xF0,0x10,0x90,0x90,0x90,0x90,0x10,0x10,0x10,0x30,0x10,0x00,0x00},/*"河",5*/
{0x00,0x04,0x02,0x00,0x03,0x3C,0x00,0x03,0x0C,0xF0,0x0C,0x03,0x00,0x00,0x00,0x00},
{0x00,0x00,0x00,0x00,0xE0,0x40,0x80,0x00,0x00,0x00,0x00,0x80,0x7E,0x00,0x00,0x00},/*"之",6*/
{0x00,0x00,0x20,0x12,0x02,0x82,0x4B,0x0A,0x2A,0x22,0x24,0x48,0x50,0x00,0x00,0x00},
{0x00,0x08,0x08,0x48,0x48,0x48,0x68,0xD8,0x48,0x48,0x48,0x08,0x08,0x08,0x00,0x00},/*"洲",7*/
{0x02,0x01,0x01,0x3E,0x24,0x18,0x08,0x10,0x25,0x38,0x12,0x2E,0x31,0x02,0x04,0x00},
{0x00,0x00,0xF8,0x88,0x40,0x20,0x40,0x78,0xC8,0x48,0x88,0x90,0x50,0x20,0x00,0x00},/*"窈",8*/
{0x02,0x01,0x11,0x1E,0x24,0x08,0x00,0x24,0x14,0x0C,0x74,0x04,0x08,0x10,0x20,0x00},
{0x00,0x00,0xF8,0x88,0x40,0x00,0x90,0xA0,0xC0,0xA0,0x94,0x84,0x84,0x7C,0x00,0x00},/*"窕",9*/
{0x00,0x02,0x22,0x13,0x02,0x83,0x5C,0x02,0x2B,0x2A,0x52,0xC3,0x06,0x02,0x00,0x00},
{0x00,0x00,0x00,0x80,0x38,0x48,0x90,0x50,0x20,0x50,0x88,0x0E,0x00,0x00,0x00,0x00},/*"淑",10*/
{0x02,0x02,0x02,0x02,0x02,0x02,0x07,0xFC,0x04,0x02,0x01,0x06,0x18,0x00,0x00,0x00},
{0x00,0x00,0x00,0x00,0x00,0x40,0xFE,0x40,0x80,0x80,0x80,0x60,0x10,0x00,0x00,0x00},/*"女",11*/
{0x00,0x01,0x0E,0x02,0x7F,0x02,0x03,0x3E,0x04,0x08,0x17,0x24,0xC4,0x07,0x00,0x00},
{0x00,0xF0,0x10,0x1E,0xE0,0x20,0xE0,0x00,0x00,0xF0,0x10,0x10,0x70,0x80,0x00,0x00},/*"君",12*/
{0x00,0x01,0x0E,0x00,0x01,0x01,0x7F,0x00,0x00,0x00,0x00,0x00,0x06,0x01,0x00,0x00},
{0x00,0xE0,0x40,0x80,0x00,0x7C,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x00},/*"子",13*/
{0x00,0x10,0x10,0x11,0x10,0x14,0x1E,0xE5,0x14,0x08,0x14,0x22,0x40,0x00,0x00,0x00},
{0x00,0x00,0x78,0x90,0x20,0x40,0x3E,0xE0,0x20,0x20,0x20,0x20,0x60,0x20,0x00,0x00},/*"好",14*/
{0x00,0x00,0x20,0x10,0x03,0x30,0xD4,0x22,0x21,0x22,0x15,0xF8,0x07,0x00,0x00,0x00},
{0x80,0x90,0x88,0xF0,0x80,0x90,0xB0,0xC0,0xA0,0x90,0x88,0x00,0x80,0x7E,0x00,0x00},/*"逑",15*/
};
uchar code CPYRT_WORDS[][16] = {
{0x00,0x08,0x04,0x04,0x7B,0x01,0x22,0x12,0x0C,0x06,0x09,0x11,0x20,0x40,0x00,0x00},
{0x00,0x02,0x04,0x24,0x24,0x24,0x24,0x24,0x24,0x24,0x24,0x04,0x04,0x0C,0x00,0x00},/*"刘",0*/
{0x00,0x01,0x00,0x00,0x3F,0x60,0x00,0x3F,0x01,0x01,0x01,0x01,0x00,0x03,0x00,0x00},
{0x00,0x00,0x80,0x04,0xFC,0x00,0x04,0xF8,0x00,0x00,0x00,0x00,0x80,0x00,0x00,0x00},/*"宁",1*/
{0x00,0x06,0x14,0x24,0x3F,0x44,0x7F,0x04,0x24,0x3F,0x24,0x24,0x25,0x04,0x00,0x00},
{0x00,0x02,0x02,0x92,0x12,0x12,0xD2,0x12,0x52,0xD2,0x52,0x42,0x82,0x0C,0x04,0x00},/*"制",2*/
{0x00,0x0C,0x08,0x09,0x11,0x1A,0x34,0x54,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x00},
{0x00,0xC0,0x80,0x04,0xF8,0x40,0x40,0x7C,0x40,0x40,0x44,0x78,0x40,0x40,0x00,0x00},/*"作",3*/
};
void Put_Wdispram(uchar code *WORDS[][8]){ //,uchar first_word
uchar i;
disword[0] = &NO_WORDS[12][0];
for(i=1;i<25;i++){
disword[i] = &WORDS[i-1][0]; //first_word+
}
}
void Put_Hdispram(){
uchar i;
for(i=0;i<10;i++){
h_dispram[i] = *(disword[i+start_word]+hang); //
}
}
void Move_Left(){
uchar i;
for(i=0;i<9;i++){
h_dispram[i] = (h_dispram[i] << (move_times)) | (h_dispram[i+1] >> (8-move_times));
}
}
void Move_Right(){
uchar i;
for(i=9;i>0;i--){
h_dispram[i] = (h_dispram[i] >> (move_times)) | (h_dispram[i-1] << (8-move_times));
}
}
void RL_Move(){
//
switch(MSG_MV){
case MSG_MV_L: //左移
Move_Left();
break;
case MSG_MV_R: //右移
Move_Right();
break;
case MSG_NONE:
break;
default:
break;
}
}
void Move_Up(){
//
uchar i,j,m,n;
for(m=0;m<16;m++){
for(n=0;n<4;n++){
for(j=0;j<16-m;j++){
for(i=0;i<10;i++){
h_dispram[i] = *(disword[i]+m+j); //
}
Show_Line();
}
for(j=16-m;j<16;j++){
for(i=0;i<10;i++){
h_dispram[i] = *(disword[i+8]+m+j-16); //0x00
}
Show_Line();
}
}
}
}
void Move_Down(){
//
uchar i,j,m,n;
for(m=0;m<16;m++){
for(n=0;n<4;n++){
for(j=0;j<m;j++){
for(i=0;i<10;i++){
h_dispram[i] = *(disword[i+8]+15-m+j); //
}
Show_Line();
}
for(j=m;j<16;j++){
for(i=0;i<10;i++){
h_dispram[i] = *(disword[i]-m+j); //0x00
}
Show_Line();
}
}
}
}
void UD_Move(){
//
switch(MSG_MV){
case MSG_MV_U: //左移
// Move_Up();
break;
case MSG_MV_D: //右移
// Move_Down();
break;
case MSG_NONE:
break;
default:
break;
}
}
void Show_Line(){
uchar m;
OE=1;
for(m =0;m<8;m++)
{
SendData = h_dispram[m+1];
SendByte();
}
STB = 0;
STB = 1; //上升沿数据锁存
RowsCan(); //行扫描
OE = 0;
// delay(); //
}
void Show_sWord(){
int m,i;//
hang = 0;
for(m=0;m<7;m++){
for(i=0;i<16;i++){
Put_Hdispram(); //把第i行放入行缓冲
Show_Line();
//delay(); //看需要
}
}
}
void Show_Move_Word(uchar code *WORDS[][8]){
int m,i;
while(1){
for(m=0;m<3;m++){ //若要上下移动 m=16
//hang = 0;
for(i=0;i<16;i++){
Put_Hdispram(); //把第i行放入行缓冲
RL_Move(); //是否要左右移动
Show_Line();
//delay(); //看需要
}
//UD_Move(); //是否要上下移动
}
//========================================
//测试左移右移切换时有跳变！！
// if(MSG_MV){
move_times++;
if((move_times == 9) && (MSG_MV == MSG_MV_L)){
move_times = 1;
Put_Wdispram(WORDS);
start_word++;
switch(STATE){
case STA_gTEMP:
Disp_Temperature(); //
Put_gTEMP(); //
if(start_word > (sizeof(TMP_WORDS)/16 - 8))
MSG_MV = MSG_MV_R;
break;
case STA_gWORD:
if(start_word > (sizeof(MY_WORDS)/16 - 8))
MSG_MV = MSG_MV_R;
default:
break;
}
if(start_word > (sizeof(TMP_WORDS)/16 - 4))
MSG_MV = MSG_MV_R;
}
else if((move_times == 9) && (MSG_MV == MSG_MV_R)){
move_times = 1;
Put_Wdispram(WORDS); //
start_word-- ;
switch(STATE){
case STA_gTEMP:
Disp_Temperature(); //
Put_gTEMP();
break;
default:
break;
}
if(start_word < 1){
MSG_MV = MSG_MV_L;
return;
}
}
// }
}
}
void Show_All_Word(){
int m,i;
//MSG_MV = MSG_MV_L;
for(start_word = 0;start_word < 8;start_word++){
for(move_times = 0; move_times < 8;move_times++){
for(m=0;m<2;m++){ //若要上下移动 m=16
for(i=0;i<16;i++){
Put_Hdispram(); //把第i行放入行缓冲
RL_Move(); //是否要左右移动
Show_Line();
}
}
}
}
}
void delay()
{
uint i;
for(i=0;i<40;i++);
}
//------------------------------------
//----------字发送子程序-----------
void SendByte(void)
{
uchar m;
for(m=0;m<8;m++)
{
CLK = 0;
Red = (SendData & 0x80); //红屏显示
// Greed = (SendData & 0x80); //绿屏显示
SendData =SendData<<1;
CLK = 1; //移位时钟上升沿
}
}
//-----------------------------------
//----------行扫描子程序-------------
void RowsCan(void)
{
P2 = P2 & 0xf0;
P2 = P2 | hang;
hang++;
if (hang>=16)
{
hang =0x00;
}
}
void initial(void)
{
OE = 1;
Red = 1;
Greed = 1;
SendData = 0x00;
hang = 0x00;
}
/*****************************************************
函数功能：延时若干微秒
入口参数：n
***************************************************/
void delaynus(unsigned char n)
{
unsigned char i;
// for(i=0;i<n;i++)
;
}
/*****************************************************
函数功能：向1302写一个字节数据
入口参数：x
***************************************************/
void Write1302(unsigned char dat)
{
unsigned char i;
SCLK=0; //拉低SCLK，为脉冲上升沿写入数据做好准备
delaynus(2); //稍微等待，使硬件做好准备
for(i=0;i<8;i++) //连续写8个二进制位数据
{
DATA=dat&0x01; //取出dat的第0位数据写入1302
delaynus(2); //稍微等待，使硬件做好准备
SCLK=1; //上升沿写入数据
delaynus(2); //稍微等待，使硬件做好准备
SCLK=0; //重新拉低SCLK，形成脉冲
dat>>=1; //将dat的各数据位右移1位，准备写入下一个数据位
}
}
/*****************************************************
函数功能：根据命令字，向1302写一个字节数据
入口参数：Cmd，储存命令字；dat，储存待写的数据
***************************************************/
void WriteSet1302(unsigned char Cmd,unsigned char dat)
{
RST=0; //禁止数据传递
SCLK=0; //确保写数居前SCLK被拉低
RST=1; //启动数据传输
delaynus(2); //稍微等待，使硬件做好准备
Write1302(Cmd); //写入命令字
Write1302(dat); //写数据
SCLK=1; //将时钟电平置于已知状态
RST=0; //禁止数据传递
}
/*****************************************************
函数功能：从1302读一个字节数据
入口参数：x
***************************************************/
unsigned char Read1302(void)
{
unsigned char i,dat;
delaynus(2); //稍微等待，使硬件做好准备
for(i=0;i<8;i++) //连续读8个二进制位数据
{
dat>>=1; //将dat的各数据位右移1位，因为先读出的是字节的最低位
if(DATA==1) //如果读出的数据是1
dat|=0x80; //将1取出，写在dat的最高位
SCLK=1; //将SCLK置于高电平，为下降沿读出
delaynus(2); //稍微等待
SCLK=0; //拉低SCLK，形成脉冲下降沿
delaynus(2); //稍微等待
}
return dat; //将读出的数据返回
}
/*****************************************************
函数功能：根据命令字，从1302读取一个字节数据
入口参数：Cmd
***************************************************/
unsigned char ReadSet1302(unsigned char Cmd)
{
unsigned char dat;
RST=0; //拉低RST
SCLK=0; //确保写数居前SCLK被拉低
RST=1; //启动数据传输
Write1302(Cmd); //写入命令字
dat=Read1302(); //读出数据
SCLK=1; //将时钟电平置于已知状态
RST=0; //禁止数据传递
return dat; //将读出的数据返回
}
/*****************************************************
函数功能： 1302进行初始化设置
***************************************************/
void Init_DS1302(void)
{
unsigned char flag;
flag= ReadSet1302(0x81);
if(flag&0x80) { //判断时钟芯片是否关闭
WriteSet1302(0x8E,0x00); //根据写状态寄存器命令字，写入不保护指令
WriteSet1302(0x80,((0/10)<<4|(0%10))); //根据写秒寄存器命令字，写入秒的初始值
WriteSet1302(0x82,((18/10)<<4|(18%10))); //根据写分寄存器命令字，写入分的初始值
WriteSet1302(0x84,((21/10)<<4|(21%10))); //根据写小时寄存器命令字，写入小时的初始值
WriteSet1302(0x86,((23/10)<<4|(23%10))); //根据写日寄存器命令字，写入日的初始值
WriteSet1302(0x88,((7/10)<<4|(7%10))); //根据写月寄存器命令字，写入月的初始值
//WriteSet1302(0x8A,2);
WriteSet1302(0x8c,((10/10)<<4|(10%10))); //根据写小时寄存器命令字，写入小时的初始值
WriteSet1302(0x90,0xa5);
WriteSet1302(0x8E,0x80);
}
//如果不想每次都初始化时间，也就是掉电后还想让时钟继续走时的话就用上面的语句
/*--------------------这是每次都初始化的语句-----------------*/
/* WriteSet1302(0x8E,0x00); //根据写状态寄存器命令字，写入不保护指令
WriteSet1302(0x80,((0/10)<<4|(0%10))); //根据写秒寄存器命令字，写入秒的初始值
WriteSet1302(0x82,((18/10)<<4|(18%10))); //根据写分寄存器命令字，写入分的初始值
WriteSet1302(0x84,((21/10)<<4|(21%10))); //根据写小时寄存器命令字，写入小时的初始值
WriteSet1302(0x86,((23/10)<<4|(23%10))); //根据写日寄存器命令字，写入日的初始值
WriteSet1302(0x88,((7/10)<<4|(7%10))); //根据写月寄存器命令字，写入月的初始值
//WriteSet1302(0x8A,2);
WriteSet1302(0x8c,((10/10)<<4|(10%10))); //根据写小时寄存器命令字，写入小时的初始值
WriteSet1302(0x90,0xa5);
WriteSet1302(0x8E,0x80);
*/
}
void write_time1302(){
WriteSet1302(0x8E,0x00); //根据写状态寄存器命令字，写入不保护指令
WriteSet1302(0x80,Time.Second); //根据写秒寄存器命令字，写入秒的初始值
WriteSet1302(0x82,Time.Minute); //根据写分寄存器命令字，写入分的初始值
WriteSet1302(0x84,Time.Hour); //根据写小时寄存器命令字，写入小时的初始值
WriteSet1302(0x86,Time.Day); //根据写日寄存器命令字，写入日的初始值
WriteSet1302(0x88,Time.Month); //根据写月寄存器命令字，写入月的初始值
WriteSet1302(0x8A,Time.Week);
WriteSet1302(0x8c,Time.Year); //根据写小时寄存器命令字，写入小时的初始值
// WriteSet1302(0x90,0xa5);
//WriteSet1302(0x8E,0x80);
}
//读时间
void Read_TIME(){
RST=0; //拉低RST
SCLK=0; //确保写数居前SCLK被拉低
RST=1; //启动数据传输
Write1302(0xbf); //写入命令字
Time.Second = Read1302() & 0x7f;
Time.Minute = Read1302() & 0x7f;
Time.Hour = Read1302() & 0x7f;
Time.Day = Read1302() & 0x7f;
Time.Month = Read1302() & 0x7f;
Time.Week= Read1302() & 0x7f;
Time.Year = Read1302() & 0x7f;
SCLK=1; //将时钟电平置于已知状态
RST=0; //禁止数据传递
/*unsigned char ReadValue; //储存从1302读取的数据
ReadValue = ReadSet1302(0x81); //从秒寄存器读数据
Time.Second =ReadValue&0x7f;//(ReadValue&0x70) + (ReadValue&0x0F);//将读出数据转化
ReadValue = ReadSet1302(0x83); //从分寄存器读
Time.Minute = ReadValue&0x7f;//(ReadValue&0x70) + (ReadValue&0x0F); //将读出数据转化
ReadValue = ReadSet1302(0x85); //从时寄存器读
Time.Hour = ReadValue&0x7f;//(ReadValue&0x70) + (ReadValue&0x0F); //将读出数据转化
ReadValue = ReadSet1302(0x87); //从分寄存器读
Time.Day = ReadValue&0x7f;//(ReadValue&0x70) + (ReadValue&0x0F); //将读出数据转化
ReadValue = ReadSet1302(0x89); //从分寄存器读
Time.Month = ReadValue&0x7f;//(ReadValue&0x70) + (ReadValue&0x0F); //将读出数据转化
ReadValue = ReadSet1302(0x8B); //从时寄存器读
Time.Week= ReadValue&0x7f;//(ReadValue&0x70) + (ReadValue&0x0F); //将读出数据转化
ReadValue = ReadSet1302(0x8d); //从分寄存器读
Time.Year = ReadValue&0x7f;//(ReadValue&0x70) + (ReadValue&0x0F); //将读出数据转化
*/ }
void Put_Adispram(uchar a){
uchar i;
//第一屏"今天是:"
disword[a+1] = &NO_WORDS[12][0]; //空格
for(i=0;i<6;i++)
disword[a+i+2] = &TIME_WORDS[i][0];
disword[a+8] = &NO_WORDS[11][0]; //":"
//第二屏
//disword[4] = &TIME_WORDS[];
}
//将年份放入到显示缓存
//需要参数:缓冲区首地址下标
void Put_Ydispram(uchar i){
disword[i+1] = &NO_WORDS[12][0];
if(Time.Year < 30 && !HIDE){
disword[i+2] = &NO_WORDS[2][0];
disword[i+3] = &NO_WORDS[0][0];
}
else if(!HIDE){
disword[i+2] = &NO_WORDS[1][0];
disword[i+3] = &NO_WORDS[9][0];
}
disword[i+4] = &NO_WORDS[Time.Year>>4][0];
disword[i+5] = &NO_WORDS[Time.Year&0x0f][0];
disword[i+6] = &TIME_WORDS[6][0];
disword[i+7] = &TIME_WORDS[7][0]; //年
disword[i+8] = &NO_WORDS[12][0];
}
//将星期放入到显示缓存
//参数:缓冲区首地址下标
void Put_Kdispram(uchar i){
disword[i+1] = &NO_WORDS[12][0];
disword[i+2] = &TIME_WORDS[12][0];
disword[i+3] = &TIME_WORDS[13][0]; //星期
disword[i+4] = &TIME_WORDS[14][0];
disword[i+5] = &TIME_WORDS[15][0];
if(STATE== STA_CHG &&HIDE){
disword[i+6] = &NO_WORDS[12][0]; //
disword[i+7] = &NO_WORDS[12][0]; //
}
else{
disword[i+6] = &WEEK_WORDS[Time.Week*2-2][0]; //
disword[i+7] = &WEEK_WORDS[Time.Week*2-1][0]; //
}
disword[i+8] = &NO_WORDS[12][0];
}
//将日期放入到显示缓存
//参数:缓冲区首地址下标
void Put_Ddispram(uchar i){
disword[i+1] = &NO_WORDS[Time.Month>>4][0]; //小时高位
disword[i+2] = &NO_WORDS[ Time.Month&0x0f][0]; //小时地位
disword[i+3] = &TIME_WORDS[8][0]; //-
disword[i+4] = &TIME_WORDS[9][0]; //分钟高位
disword[i+5] = &NO_WORDS[ Time.Day>>4][0]; //分钟地位
disword[i+6] = &NO_WORDS[Time.Day&0x0f][0]; //-
disword[i+7] = &TIME_WORDS[10][0]; //秒高位
disword[i+8] = &TIME_WORDS[11][0]; //秒地位
}
//将时间放入到显示缓存
//参数:缓冲区首地址下标
void Put_Tdispram(uchar i){
disword[i+1] = &NO_WORDS[Time.Hour>>4][0]; //小时高位
disword[i+2] = &NO_WORDS[ Time.Hour&0x0f][0]; //小时地位
disword[i+3] = &NO_WORDS[ 11 ]; //-
disword[i+4] = &NO_WORDS[Time.Minute>>4][0]; //分钟高位
disword[i+5] = &NO_WORDS[ Time.Minute&0x0f][0]; //分钟地位
disword[i+6] = &NO_WORDS[ 11 ]; //-
disword[i+7] = &NO_WORDS[Time.Second>>4][0]; //秒高位
disword[i+8] = &NO_WORDS[ Time.Second&0x0f][0]; //秒地位
}
//===================================
//*****关于温度检测部分*****
void Put_gTEMP(){
// uchar i;
// Put_Wdispram(TMP_WORDS,0);
disword[6] = &NO_WORDS[temp_ram[3]][0]; //百位
disword[7] = &NO_WORDS[temp_ram[2]][0]; //十位
disword[8] = &NO_WORDS[temp_ram[1]][0]; //个位
disword[10] = &NO_WORDS[temp_ram[0]][0]; //小数
disword[12] = &NO_WORDS[12]; //空格
disword[13] = &NO_WORDS[12]; //空格
//
}
void Put_sTEMP(uchar i){
disword[i+1] = &NO_WORDS[12]; //空格
disword[i+2] = &NO_WORDS[12];//&NO_WORDS[temp_ram[3]][0]; //百位
disword[i+3] = &NO_WORDS[temp_ram[2]][0]; //十位
disword[i+4] = &NO_WORDS[temp_ram[1]][0]; //个位
disword[i+5] = &TMP_WORDS[8][0]; //小数点
disword[i+6] = &NO_WORDS[temp_ram[0]][0]; //小数
disword[i+7] = &TMP_WORDS[10][0];
disword[i+8] = &NO_WORDS[12]; //空格
}
void Put_Cpyrt(uchar i){
uchar m;
for(m=0;m<8;m++)
disword[i+1+m] = &CPYRT_WORDS[m];
}
void Show_Cpyrt(){
uchar i;
for(i=1;i<9;i++)
disword[i] = &NO_WORDS[12];
Put_Cpyrt(8);
Move_Down();
Put_Cpyrt(0);
Put_Tdispram(8);
Move_Down();
}
//========================
//参数i:放入第几屏缓存
//参数j:诗歌第几页
//========================
void Put_Song(uchar i,uchar j){
uchar m;
for(m=0;m<8;m++)
disword[i+1+m] = &SONG_WORDS[j+m];
}
//显示诗歌
void Show_Song(){
uchar i;
Put_Song(8,0);
Move_Up();
for(i=0;i<3;i++){
Put_Song(0,i*8);
Put_Song(8, (i+1)*8);
Move_Up();
}
Put_Song(0, 3*8);
Put_Tdispram(8);
Move_Up();
}
//======================
//*滚动显示所有信息*
//======================
void Show_All_Info(){
Put_Adispram(8);
Move_Down(); //切换效果
Put_Adispram(0);
Put_Ydispram(8); //XXXX年
Show_All_Word();
Put_Ydispram(0); //XXXX年
Put_Ddispram(8);
Show_All_Word();
Put_Ddispram(0);
Put_Kdispram(8);
Show_All_Word();
Read_Temperature();
Disp_Temperature();
Put_Kdispram(0);
Put_Tdispram(8);
Show_All_Word();
Read_Temperature();
Disp_Temperature();
Put_Tdispram(0);
Put_sTEMP(8);
Show_All_Word();
Read_TIME();
Put_sTEMP(0);
Put_Tdispram(8);
Move_Up();
}
/*us级延时函数 */
/*******************************************************************/
void Delay(unsigned int num)
{
num = num/2;
while( --num ) ;
}
/*初始化ds1820 */
/*******************************************************************/
Init_DS18B20(void)
{
DQ = 1 ; //DQ复位
Delay(8) ; //稍做延时
DQ = 0 ; //单片机将DQ拉低
Delay(90) ; //精确延时大于 480us
DQ = 1 ; //拉高总线
Delay(8) ;
presence = DQ ; //如果=0则初始化成功 =1则初始化失败
Delay(100) ;
DQ = 1 ;
return(presence) ; //返回信号，0=presence,1= no presence
}
/* 读一个字节 */
/*******************************************************************/
ReadOneChar(void)
{
unsigned char i = 0 ;
unsigned char dat = 0 ;
for (i = 8 ; i > 0 ; i--)
{
DQ = 0 ; // 给脉冲信号
dat >>= 1 ;
DQ = 1 ; // 给脉冲信号
if(DQ)
dat |= 0x80 ;
Delay(4) ;
}
return (dat) ;
}
/* 写一个字节 */
/*******************************************************************/
WriteOneChar(unsigned char dat)
{
unsigned char i = 0 ;
for (i = 8 ; i > 0 ; i--)
{
DQ = 0 ;
DQ = dat&0x01 ;
Delay(5) ;
DQ = 1 ;
dat>>=1 ;
}
}
/* 读取温度 */
/*******************************************************************/
Read_Temperature(void)
{
Init_DS18B20() ;
WriteOneChar(0xCC) ; // 跳过读序号列号的操作
WriteOneChar(0x44) ; // 启动温度转换
Init_DS18B20() ;
WriteOneChar(0xCC) ; //跳过读序号列号的操作
WriteOneChar(0xBE) ; //读取温度寄存器
temp_data[0] = ReadOneChar() ; //温度低8位
temp_data[1] = ReadOneChar() ; //温度高8位
}
/* 数据转换与温度显示 */
/*******************************************************************/
void Disp_Temperature()
{
temp_ram[4]=temp_data[0]&0x0f ;
temp_ram[0]=ditab[temp_ram[4]]+0x30 ; //查表得小数位的值
temp_ram[4]=((temp_data[0]&0xf0)>>4)|((temp_data[1]&0x0f)<<4) ;
temp_ram[3]=temp_ram[4]/100+0x30 ;
temp_ram[1]=temp_ram[4]%100 ;
temp_ram[2]=temp_ram[1]/10+0x30 ;
temp_ram[1]=temp_ram[1]%10+0x30 ;
if(temp_ram[3]==0x30) //高位为0，不显示
{
temp_ram[3]=0x20 ;
if(temp_ram[2]==0x30) //次高位为0，不显示
temp_ram[2]=0x20 ;
}
}
void start_time(){
Time.Year = 0x10;
Time.Month = 0x7;
Time.Day = 0x23;
Time.Hour = 0x21;
Time.Minute = 0x58;
Time.Second = 0x0;
Time.Week = 0x5;
}
//=================
//****校时函数****
//=================
void Change_Time(){
//
MSG_MV = MSG_MV_L;
move_times = 0;
start_word=0;
TMP_TIME = Time.Hour;
TR1 = 1; //开启定时器1闪烁
do{
switch(CHANGE){
case CHG_HOUR:
case CHG_MIN:
case CHG_SEC:
Put_Tdispram(0);
break;
case CHG_MON:
case CHG_DAY:
Put_Ddispram(0);
break;
case CHG_WEEK:
Put_Kdispram(0);
break;
case CHG_YEAR:
Put_Ydispram(0);
break;
default:
break;
}
Show_sWord();
//if(!key_done)
// ReadKey1();
}while(ReadKey1() != KEY3_S && exit < 10); //MSG_KEY
Change_obj(); //保证退出校时无隐身
HIDE = 0;
key_done = 0;
//key_done = 1; //按键事件处理完成
TR1 = 0; //关闭定时器1闪烁
}
//==================
//****对象切换****
//==================
void Change_obj(){
switch(CHANGE){
case CHG_HOUR:
if(Time.Hour == 0xcc)
Time.Hour = TMP_TIME;
TMP_TIME = Time.Minute;
break;
case CHG_MIN:
if(Time.Minute == 0xcc)
Time.Minute = TMP_TIME;
TMP_TIME = Time.Second;
break;
case CHG_SEC:
if(Time.Second == 0xcc)
Time.Second = TMP_TIME;
TMP_TIME = Time.Month;
break;
case CHG_MON:
if(Time.Month == 0xcc)
Time.Month = TMP_TIME;
TMP_TIME = Time.Day;
break;
case CHG_DAY:
if(Time.Day == 0xcc)
Time.Day = TMP_TIME;
TMP_TIME = Time.Week;
break;
case CHG_WEEK:
if(Time.Week == 0xcc)
Time.Week = TMP_TIME;
TMP_TIME = Time.Year;
break;
case CHG_YEAR:
if(Time.Year == 0xcc)
Time.Year = TMP_TIME;
TMP_TIME = Time.Hour;
break;
default:
break;
}
}
//==================
//****加加函数****
//功能: 0x19 ++ =0x20
//==================
uchar Add_num(char *num){
++(*num);
if(((*num) & 0x0f) == 0x0a){
*num += 0x10;
*num &= 0xf0;
}
return *num;
}
//==================
//****校时加加****
//==================
void Add_Time(){
switch(CHANGE){
case CHG_HOUR:
if(HIDE){
if(Add_num(&TMP_TIME) == 0x24)
TMP_TIME= 0;
}
else{
if(Add_num(&Time.Hour) == 0x24)
Time.Hour = 0;
}
break;
case CHG_MIN:
if(HIDE){
if(Add_num(&TMP_TIME) == 0x60)
TMP_TIME= 0;
}
else{
if(Add_num(&Time.Minute) == 0x60)
Time.Minute= 0;
}
break;
case CHG_SEC:
if(HIDE){
if(Add_num(&TMP_TIME) == 0x60)
TMP_TIME= 0;
}
else{
if(Add_num(&Time.Second) == 0x60)
Time.Second = 0;
}
break;
case CHG_MON:
if(HIDE){
if(Add_num(&TMP_TIME) == 0x13)
TMP_TIME= 0;
}
else{
if(Add_num(&Time.Month) == 0x13)
Time.Month= 1;
}
break;
case CHG_DAY:
if(HIDE){
if(Add_num(&TMP_TIME) == 0x32)
TMP_TIME= 0;
}
else{
if(Add_num(&Time.Day) == 0x32)
Time.Day= 0;
}
break;
case CHG_WEEK:
if(HIDE){
if(Add_num(&TMP_TIME) == 0x08)
TMP_TIME= 0;
}
else{
if(Add_num(&Time.Week) == 0x08)
Time.Week= 1;
}
break;
case CHG_YEAR:
if(HIDE){
if(Add_num(&TMP_TIME) == 0xa0)
TMP_TIME = 0;
}
else{
if(Add_num(&Time.Year) == 0xa0)
Time.Year = 0;
}
//if(Add_num(&Time.Year) == 0x24)
// Time.Year= 0;
break;
default:
break;
}
}
//==================
//****减减函数****
//功能: 0x20 -- =0x19
//==================
uchar Cut_num(char *num){
--(*num);
if(((*num)&0x0f) == 0x0f){
//*num -= 0x10;
*num &= 0xf9;
}
//if((*num == 0xf9)
//*num = 0x99;
return *num;
}
//==================
//****校时减减****
//==================
void Cut_Time(){
switch(CHANGE){
case CHG_HOUR:
if(HIDE){
if(Cut_num(&TMP_TIME) == 0xf9)
TMP_TIME= 0x23;
}
else{
if(Cut_num(&Time.Hour) == 0xf9)
Time.Hour = 0x23;
}
break;
case CHG_MIN:
if(HIDE){
if(Cut_num(&TMP_TIME) == 0xf9)
TMP_TIME= 0x59;
}
else{
if(Cut_num(&Time.Minute) == 0xf9)
Time.Minute= 0x59;
}
break;
case CHG_SEC:
if(HIDE){
if(Cut_num(&TMP_TIME) == 0xf9)
TMP_TIME= 0x59;
}
else{
if(Cut_num(&Time.Second) == 0xf9)
Time.Second = 0x59;
}
break;
case CHG_MON:
if(HIDE){
if(Cut_num(&TMP_TIME) == 0xf9)
TMP_TIME= 0x12;
}
else{
if(Cut_num(&Time.Month) == 0xf9)
Time.Month= 0x12;
}
break;
case CHG_DAY:
if(HIDE){
if(Cut_num(&TMP_TIME) == 0xf9)
TMP_TIME= 0x31;
}
else{
if(Cut_num(&Time.Day) == 0xf9)
Time.Day= 0x31;
}
break;
case CHG_WEEK:
if(HIDE){
if(Cut_num(&TMP_TIME) == 0xf9)
TMP_TIME= 0x7;
}
else{
if(Cut_num(&Time.Week) == 0xf9)
Time.Week= 0x7;
}
break;
case CHG_YEAR:
if(HIDE){
if(Cut_num(&TMP_TIME) == 0xf9)
TMP_TIME= 0x99;
}
else{
if(Cut_num(&Time.Year) == 0xf9)
Time.Year = 0x99;
}
//if(Cut_num(&Time.Year) == 0x99)
// Time.Year= 0;
break;
default:
break;
}
}
//======按键======
uchar ReadKey(){
//
if(!key_done){
switch(MSG_KEY){
case KEY0_S:STATE = STA_sTIME;
break;
case KEY1_S:STATE = STA_gWORD; //STA_sWEEK
break;
case KEY2_S:STATE = STA_gTEMP;
break;
case KEY3_S:STATE = STA_gTIME;
break;
case KEY0_L:STATE = STA_CHG;
break;
case KEY1_L:STATE = STA_SONG;
break;
case KEY2_L:STATE = STA_gTEMP;
break;
case KEY3_L:STATE = STA_gWORD; //STA_sTIME
break;
default: break;
}
}
key_done = 1; //按键事件处理完成
return MSG_KEY;
}
//=======================
//****校时按键处理****
//=======================
uchar ReadKey1(){
//
if(!key_done){
switch(MSG_KEY){
case KEY0_S: //切换校时对象
case KEY0_L:
exit = 0;
TR1 = 0; //关闭定时器1闪烁
Change_obj();
if(CHANGE++ >= CHG_YEAR)
CHANGE = CHG_HOUR;
TR1 = 1; //开启定时器1闪烁
break;
case KEY1_S: //加加
case KEY1_L:
exit = 0;
TR1 = 0; //关闭定时器1闪烁
Add_Time();
TR1 = 1; //开启定时器1闪烁
break;
case KEY2_S: //减减
case KEY2_L:
exit = 0;
TR1 = 0; //关闭定时器1闪烁
Cut_Time();
TR1 = 1; //开启定时器1闪烁
break;
case KEY3_L:
case KEY3_S:
return KEY3_S;
default: break;
}
}
key_done = 1; //按键事件处理完成
return 0;
}
//===========================
void Tinit(){
TMOD = 0x11;
TH0 = 0xD8;
TL0 = 0xF0;
TH1 = 0x42;
TL1 = 0xCA;
TR0 = 1;
//TR1 = 1;
ET0 = 1;
ET1 = 1;
EA = 1;
}
timer0() interrupt 1{
TH0 = 0xD8;
TL0 = 0xF0;
if(P1 != 0xff) {//若有键按下
cur_key_val = P1&0x0f; //记录按键值
if(key_times < 150)
key_times++;
else{
key_keep_times++; //长按连击
if(key_keep_times >= 10){ //10 1秒连击10次
key_keep_times = 0;
MSG_KEY = 0x10 | cur_key_val;
key_done = 0; //按键事件复位
}
}
}else{
if(key_times > 2 && key_times < 100 && key_done){ //短按键
MSG_KEY = cur_key_val;
key_done = 0; //按键事件复位
……………………
…………限于本文篇幅余下代码请从51黑下载附件…………

复制代码

所有资料51hei提供下载:

led点阵时钟.rar (1.92 MB, 下载次数: 131)

ID:140183 · 发表于 2018-1-21 17:40

多谢分享!!!!!!!!

ID:298252 · 发表于 2018-3-28 14:58

很不错的分享

ID:459203 · 发表于 2019-2-11 14:46

很不错的分享

ID:489822 · 发表于 2019-4-24 22:31

多谢分享!!!!!!!!

ID:601669 · 发表于 2019-8-19 17:03

感谢分享！

ID:90776 · 发表于 2019-9-7 00:20

多谢分享!!!!!!!!

ID:613211 · 发表于 2019-11-6 10:45

太牛了，谢谢分享，学习了

ID:638375 · 发表于 2019-11-8 22:40

谢谢分享！！

ID:648302 · 发表于 2019-12-21 13:41

big_zhuang 发表于 2019-2-11 14:46
很不错的分享

可以发下原理图不

ID:577423 · 发表于 2019-12-21 21:45

max7219怎么改

ID:632676 · 发表于 2019-12-22 22:11

有没有图

帐号		自动登录	找回密码
密码			立即注册