光立方的详细制作教程含程序详解原理图和仿真电路图等图片和资料下载

ID:169468 · 发表于 2017-3-9 19:40

如何制作光立方，带有视频，ad画的原理图，单片机仿真电路图等很详细的教程

带有光立方的程序详解，注释非常详细。
所有资料下载：

光立方制作.zip (18.97 MB, 下载次数: 1839)

2017-3-9 19:38 上传

点击文件名下载附件
光立方制作教程

光立方制作成功后的效果图片：

光立方的原理：

仿真制作原理：先从P0口给控制共阴端的573锁入相应的数值，然后给共阳端再送人相应的数值，这样与共阴端的相呼应就可点亮相应的灯.
光立方的proteus仿真原理图：

下面是光立方的制作过程，非常详细：

光立方的单片机源程序：

/*锐锐制作光立方源程序*/
#include<reg51.h> //包含头文件，一般情况不需要改动，头文件包含特殊功能寄存器的定义
#define DataPort P0 //定义数据端口程序中遇到DataPort 则用P0 替换
sbit line_LATCH=P1^0;//定义锁存使能端口行扫描的锁存端口
sbit LATCH1=P2^0;//定义锁存使能端口第一灯板的字节锁存
sbit LATCH2=P2^1;//
sbit LATCH3=P2^2;//
sbit LATCH4=P2^3;
sbit LATCH5=P2^4;
sbit LATCH6=P2^5;
sbit LATCH7=P2^6;
sbit LATCH8=P2^7;
void Delay(unsigned int t)
{
while(--t);
}
unsigned char line[8]={0xfe,0xfd,0xfb,0xf7,0xef,0xdf,0xbf,0x7f};// 显示行值01234567
void display(unsigned char *Data)//显示子程序，指针数组作为形参，直接指向传过来的实参数组的地址，这样就可直接操纵数组传过来的数组了
{
unsigned char i;
for(i=0;i<8;i++)
{
DataPort=line[i]; //先给行（灯板的公共端）输入数据
line_LATCH=1; //打开锁存，把数据line[i]放进去
line_LATCH=0; //关闭锁存，阻止外部数据进来
DataPort=Data[i]; //把数组Data[0~7]里的值依次传给第一灯板的573锁存器中
LATCH1=1;LATCH1=0;
DataPort=Data[8+i]; //把数组Data[8~15]里的值依次传给第二灯板的573锁存器中
LATCH2=1;LATCH2=0;
DataPort=Data[16+i]; //把数组Data[16~23]里的值依次传给第三灯板的573锁存器中
LATCH3=1;LATCH3=0;
DataPort=Data[24+i];
LATCH4=1;LATCH4=0;
DataPort=Data[32+i];
LATCH5=1;LATCH5=0;
DataPort=Data[40+i];
LATCH6=1;LATCH6=0;
DataPort=Data[48+i];
LATCH7=1;LATCH7=0;
DataPort=Data[56+i];
LATCH8=1;LATCH8=0;
Delay(200); //扫描间隙延时，时间太长会闪烁，太短会造成重影
DataPort=0xff; // 清空行锁存器里数据，防止出现乱码
line_LATCH=1; //
line_LATCH=0;
} /*如此一趟循环下来，每次都是8块灯板的同一行一起点亮，
如此组成一个灯板，8次循环下来，就全部灯都点亮了*/
}
void liang() //点亮所有的灯
{
unsigned int i;
for(i=0;i<5000;i++)
{
DataPort=0x00; //先给行（灯板的公共端）输入数据
line_LATCH=1; //打开锁存，把数据0x00放进去
line_LATCH=0; //关闭锁存，阻止外部数据进来
DataPort=0xff; //把0xff送进锁存器1~8中，使它们的输出引脚都输出高电平，与行锁存器的0x00相对，点亮所有的灯
LATCH1=1;LATCH1=0;
LATCH2=1;LATCH2=0;
LATCH3=1;LATCH3=0;
LATCH4=1;LATCH4=0;
LATCH5=1;LATCH5=0;
LATCH6=1;LATCH6=0;
LATCH7=1;LATCH7=0;
LATCH8=1;LATCH8=0;
}
}
void mie() //熄灭所有的灯
{
unsigned int i;
for(i=0;i<5000;i++)
{
DataPort=0x00; //先给行（灯板的公共端）输入数据
line_LATCH=1; //打开锁存，把数据0x00放进去
line_LATCH=0; //关闭锁存，阻止外部数据进来
DataPort=0x00; //把0x00送进锁存器1~8中，使它们的输出引脚都输出高电平，与行锁存器的0x00相对，熄灭所有的灯
LATCH1=1;LATCH1=0;
LATCH2=1;LATCH2=0;
LATCH3=1;LATCH3=0;
LATCH4=1;LATCH4=0;
LATCH5=1;LATCH5=0;
LATCH6=1;LATCH6=0;
LATCH7=1;LATCH7=0;
LATCH8=1;LATCH8=0;
}
}
void Laihui() //来回灯板显示效果
{
unsigned char i;
unsigned char code laihui0[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//定义空间为64的数组并赋值，用以传递给显示子程序
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff
};
unsigned char code laihui1[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code laihui2[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code laihui3[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code laihui4[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code laihui5[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code laihui6[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code laihui7[]={0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
for(i=0;i<10;i++) display(laihui0);//调用显示子程序display，并把数组laihui0的数组名作为实参传给指针式形参
for(i=0;i<10;i++) display(laihui1);
for(i=0;i<10;i++) display(laihui2);
for(i=0;i<10;i++) display(laihui3);
for(i=0;i<10;i++) display(laihui4);
for(i=0;i<10;i++) display(laihui5);
for(i=0;i<10;i++) display(laihui6);
for(i=0;i<10;i++) display(laihui7);
for(i=0;i<10;i++) display(laihui7);
for(i=0;i<10;i++) display(laihui6);
for(i=0;i<10;i++) display(laihui5);
for(i=0;i<10;i++) display(laihui4);
for(i=0;i<10;i++) display(laihui3);
for(i=0;i<10;i++) display(laihui2);
for(i=0;i<10;i++) display(laihui1);
for(i=0;i<10;i++) display(laihui0);
}
void Zhengfang() //显示正方形方框
{
unsigned char i;
unsigned char code zhengfang1[]={0xff,0x81,0x81,0x81,0x81,0x81,0x81,0xff,
0x81,0x00,0x00,0x00,0x00,0x00,0x00,0x81,
0x81,0x00,0x00,0x00,0x00,0x00,0x00,0x81,
0x81,0x00,0x00,0x00,0x00,0x00,0x00,0x81,
0x81,0x00,0x00,0x00,0x00,0x00,0x00,0x81,
0x81,0x00,0x00,0x00,0x00,0x00,0x00,0x81,
0x81,0x00,0x00,0x00,0x00,0x00,0x00,0x81,
0xff,0x81,0x81,0x81,0x81,0x81,0x81,0xff
};
unsigned char code zhengfang2[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x7e,0x42,0x42,0x42,0x42,0x7e,0x00,
0x00,0x42,0x00,0x00,0x00,0x00,0x42,0x00,
0x00,0x42,0x00,0x00,0x00,0x00,0x42,0x00,
0x00,0x42,0x00,0x00,0x00,0x00,0x42,0x00,
0x00,0x42,0x00,0x00,0x00,0x00,0x42,0x00,
0x00,0x7e,0x42,0x42,0x42,0x42,0x7e,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code zhengfang3[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x3c,0x00,0x00,0x3c,0x00,0x00,
0x00,0x00,0x24,0x00,0x00,0x24,0x00,0x00,
0x00,0x00,0x24,0x00,0x00,0x24,0x00,0x00,
0x00,0x00,0x3c,0x00,0x00,0x3c,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code zhengfang4[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
for(i=0;i<20;i++)display(zhengfang1);
for(i=0;i<14;i++)display(zhengfang2);
for(i=0;i<14;i++)display(zhengfang3);
for(i=0;i<14;i++)display(zhengfang4);
for(i=0;i<14;i++)display(zhengfang4);
for(i=0;i<14;i++)display(zhengfang3);
for(i=0;i<14;i++)display(zhengfang2);
for(i=0;i<14;i++)display(zhengfang1);
for(i=0;i<4;i++)
{
for(i=0;i<3;i++)display(zhengfang1);
for(i=0;i<3;i++)display(zhengfang2);
for(i=0;i<3;i++)display(zhengfang3);
for(i=0;i<3;i++)display(zhengfang4);
for(i=0;i<3;i++)display(zhengfang4);
for(i=0;i<3;i++)display(zhengfang3);
for(i=0;i<3;i++)display(zhengfang2);
for(i=0;i<3;i++)display(zhengfang1);
}
}
void Xin() //显示心形图案
{
unsigned char code xin[]={ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x28,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x44,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x82,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x92,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x6c,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
display(xin);
}
void Zhahua() //显示炸花式效果
{
unsigned char i;
unsigned char code zhahua1[64]={0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff
};
unsigned char code zhahua2[64]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x7e,0x7e,0x7e,0x7e,0x7e,0x7e,0x00,
0x00,0x7e,0x7e,0x7e,0x7e,0x7e,0x7e,0x00,
0x00,0x7e,0x7e,0x7e,0x7e,0x7e,0x7e,0x00,
0x00,0x7e,0x7e,0x7e,0x7e,0x7e,0x7e,0x00,
0x00,0x7e,0x7e,0x7e,0x7e,0x7e,0x7e,0x00,
0x00,0x7e,0x7e,0x7e,0x7e,0x7e,0x7e,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code zhahua3[64]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x3c,0x3c,0x3c,0x3c,0x00,0x00,
0x00,0x00,0x3c,0x3c,0x3c,0x3c,0x00,0x00,
0x00,0x00,0x3c,0x3c,0x3c,0x3c,0x00,0x00,
0x00,0x00,0x3c,0x3c,0x3c,0x3c,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code zhahua4[64]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00,
0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
for(i=0;i<6;i++)
{
for(i=0;i<18;i++)display(zhahua1);//用for循环多调用几次，可增加显示的时间，可省去延时的调用
for(i=0;i<18;i++)display(zhahua2);
for(i=0;i<18;i++)display(zhahua3);
for(i=0;i<21;i++)display(zhahua4);
for(i=0;i<18;i++)display(zhahua3);
for(i=0;i<18;i++)display(zhahua2);
for(i=0;i<18;i++)display(zhahua1);
}
for(i=0;i<6;i++)
{
for(i=0;i<5;i++)display(zhahua1);
for(i=0;i<5;i++)display(zhahua2);
for(i=0;i<5;i++)display(zhahua3);
for(i=0;i<6;i++)display(zhahua4);
for(i=0;i<5;i++)display(zhahua3);
for(i=0;i<5;i++)display(zhahua2);
for(i=0;i<5;i++)display(zhahua1);
}
}
void Budai() //布带抖动效果
{
unsigned char i;
unsigned char code budai0[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0xff,0x00,
0x00,0x00,0x00,0x00,0x00,0xff,0x00,0x00,
0x00,0x00,0x00,0x00,0xff,0x00,0x00,0x00,
0x00,0x00,0x00,0xff,0x00,0x00,0x00,0x00,
0x00,0x00,0xff,0x00,0x00,0x00,0x00,0x00,
0x00,0xff,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code budai1[]={0x00,0x00,0x00,0x00,0x00,0x00,0xff,0x00,
0x00,0x00,0x00,0x00,0x00,0xff,0x00,0xff,
0x00,0x00,0x00,0x00,0xff,0x00,0x00,0x00,
0x00,0x00,0x00,0xff,0x00,0x00,0x00,0x00,
0x00,0x00,0xff,0x00,0x00,0x00,0x00,0x00,
0x00,0xff,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code budai2[]={0x00,0x00,0x00,0x00,0x00,0xff,0x00,0x00,
0x00,0x00,0x00,0x00,0xff,0x00,0xff,0x00,
0x00,0x00,0x00,0xff,0x00,0x00,0x00,0xff,
0x00,0x00,0xff,0x00,0x00,0x00,0x00,0x00,
0x00,0xff,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code budai3[]={0x00,0x00,0x00,0x00,0xff,0x00,0x00,0x00,
0x00,0x00,0x00,0xff,0x00,0xff,0x00,0x00,
0x00,0x00,0xff,0x00,0x00,0x00,0xff,0x00,
0x00,0xff,0x00,0x00,0x00,0x00,0x00,0xff,
0xff,0x00,0x00,0x00,0x00,0x00,0x00,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code budai4[]={0x00,0x00,0x00,0xff,0x00,0x00,0x00,0x00,
0x00,0x00,0xff,0x00,0xff,0x00,0x00,0x00,
0x00,0xff,0x00,0x00,0x00,0xff,0x00,0x00,
0xff,0x00,0x00,0x00,0x00f,0x00,0xff,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code budai5[]={0x00,0x00,0xff,0x00,0x00,0x00,0x00,0x00,
0x00,0xff,0x00,0xff,0x00,0x00,0x00,0x00,
0xff,0x00,0x00,0x00,0xff,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0xff,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0xff,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code budai6[]={0x00,0xff,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0x00,0xff,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0xff,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0xff,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0xff,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0xff,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code budai7[]={0xff,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0xff,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0xff,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0xff,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0xff,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0xff,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0xff,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xff
};
unsigned char code budai8[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0xff,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0xff,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0xff,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0xff,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0xff,0x00,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0xff,0x00
};
unsigned char code budai9[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0xff,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0xff,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0xff,0x00,0x00,0x00,0xff,
0x00,0x00,0x00,0x00,0xff,0x00,0xff,0x00,
0x00,0x00,0x00,0x00,0x00,0xff,0x00,0x00
};
unsigned char code budai10[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0xff,0x00,0x00,0x00,0x00,0x00,0xff,
0x00,0x00,0xff,0x00,0x00,0xff,0xff,0x00,
0x00,0x00,0x00,0xff,0x00,0xff,0x00,0x00,
0x00,0x00,0x00,0x00,0xff,0x00,0x00,0xff
};
unsigned char code budai11[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xff,
0xff,0x00,0x00,0x00,0x00,0x00,0xff,0x00,
0x00,0xff,0x00,0x00,0x00,0xff,0x00,0x00,
0x00,0x00,0xff,0x00,0xff,0x00,0x00,0x00,
0x00,0x00,0x00,0xff,0x00,0x00,0x00,0x00
};
unsigned char code budai12[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0xff,0x00,
0x00,0x00,0x00,0x00,0x00,0xff,0x00,0x00,
0xff,0x00,0x00,0x00,0xff,0x00,0x00,0x00,
0x00,0xff,0x00,0xff,0x00,0x00,0x00,0x00,
0x00,0x00,0xff,0x00,0x00,0x00,0x00,0x00
};
unsigned char code budai13[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0xff,0x00,
0x00,0x00,0x00,0x00,0x00,0xff,0x00,0x00,
0x00,0x00,0x00,0x00,0xff,0x00,0x00,0x00,
0x00,0x00,0x00,0xff,0x00,0x00,0x00,0x00,
0xff,0x00,0xff,0x00,0x00,0x00,0x00,0x00,
0x00,0xff,0x00,0x00,0x00,0x00,0x00,0x00
};
unsigned char code budai14[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xff,
0x00,0x00,0x00,0x00,0x00,0x00,0xff,0x00,
0x00,0x00,0x00,0x00,0x00,0xff,0x00,0x00,
0x00,0x00,0x00,0x00,0xff,0x00,0x00,0x00,
0x00,0x00,0x00,0xff,0x00,0x00,0x00,0x00,
0x00,0x00,0xff,0x00,0x00,0x00,0x00,0x00,
0x00,0xff,0x00,0x00,0x00,0x00,0x00,0x00,
0xff,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
for(i=0;i<8;i++) display(budai0);
for(i=0;i<8;i++) display(budai1);
for(i=0;i<8;i++) display(budai2);
for(i=0;i<8;i++) display(budai3);
for(i=0;i<8;i++) display(budai4);
for(i=0;i<8;i++) display(budai5);
for(i=0;i<8;i++) display(budai6);
for(i=0;i<8;i++) display(budai7);
for(i=0;i<8;i++) display(budai8);
for(i=0;i<8;i++) display(budai9);
for(i=0;i<8;i++) display(budai10);
for(i=0;i<8;i++) display(budai11);
for(i=0;i<8;i++) display(budai12);
for(i=0;i<8;i++) display(budai13);
for(i=0;i<8;i++) display(budai14);
}
unsigned char Data0[8]={0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01};// 显示
unsigned char Data1[8]={0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x02};// 显示
unsigned char Data2[8]={0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x04};// 显示
unsigned char Data3[8]={0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08};// 显示
unsigned char Data4[8]={0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10};// 显示
unsigned char Data5[8]={0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20};// 显示
unsigned char Data6[8]={0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40};// 显示
unsigned char Data7[8]={0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,};
void display1(unsigned char *Data)//显示功能模块
{
unsigned char i,j,k,num=0;
for(k=0;k<10;k++)
{
DataPort=0x00; // 清空行锁存器里数据，防止出现乱码
line_LATCH=1; //
line_LATCH=0;
LATCH1=1;LATCH1=0;
LATCH2=1;LATCH2=0;
LATCH3=1;LATCH3=0;
LATCH4=1;LATCH4=0;
LATCH5=1;LATCH5=0;
LATCH6=1;LATCH6=0;
LATCH7=1;LATCH7=0;
LATCH8=1;LATCH8=0;
for(j=0;j<45&&num<=8&&num>=1;j++)
{
DataPort=0xff; // 清空行锁存器里数据，防止出现乱码
line_LATCH=1; //
line_LATCH=0;
for(i=0;i<8;i++)
{
DataPort=line[i]; //先给行（灯板的公共端）输入数据
line_LATCH=1; //打开锁存，把数据line[i]放进去
line_LATCH=0; //关闭锁存，阻止外部数据进来
DataPort=Data[i]; //把数值Data[0~7]里的值依次传给第一灯板的573锁存器中
if(num==1){LATCH1=1;LATCH1=0;}
else if(num==2){LATCH2=1;LATCH2=0;}
else if(num==3){LATCH3=1;LATCH3=0;}
else if(num==4){LATCH4=1;LATCH4=0;}
else if(num==5){LATCH5=1;LATCH5=0;}
else if(num==6){LATCH6=1;LATCH6=0;}
else if(num==7){LATCH7=1;LATCH7=0;}
else if(num==8){LATCH8=1;LATCH8=0;}
Delay(100); //扫描间隙延时，时间太长会闪烁，太短会造成重影
}
}
num++;
if(num==9)num=0;
}
}
void display2(unsigned char *Data)//显示功能模块
{
unsigned char i,j,k,num=9;
for(k=0;k<10;k++)
{
DataPort=0x00; // 清空行锁存器里数据，防止出现乱码
line_LATCH=1; //
line_LATCH=0;
LATCH1=1;LATCH1=0;
LATCH2=1;LATCH2=0;
LATCH3=1;LATCH3=0;
LATCH4=1;LATCH4=0;
LATCH5=1;LATCH5=0;
LATCH6=1;LATCH6=0;
LATCH7=1;LATCH7=0;
LATCH8=1;LATCH8=0;
for(j=0;j<45&&num<=8&&num>=1;j++)
{
DataPort=0xff; // 清空行锁存器里数据，防止出现乱码
line_LATCH=1; //
line_LATCH=0;
for(i=0;i<8;i++)
{
DataPort=line[i]; //先给行（灯板的公共端）输入数据
line_LATCH=1; //打开锁存，把数据line[i]放进去
line_LATCH=0; //关闭锁存，阻止外部数据进来
DataPort=Data[i]; //把数值Data[0~7]里的值依次传给第一灯板的573锁存器中
if(num==1){LATCH1=1;LATCH1=0;}
else if(num==2){LATCH2=1;LATCH2=0;}
else if(num==3){LATCH3=1;LATCH3=0;}
else if(num==4){LATCH4=1;LATCH4=0;}
else if(num==5){LATCH5=1;LATCH5=0;}
else if(num==6){LATCH6=1;LATCH6=0;}
else if(num==7){LATCH7=1;LATCH7=0;}
else if(num==8){LATCH8=1;LATCH8=0;}
Delay(100); //扫描间隙延时，时间太长会闪烁，太短会造成重影
}
}
num--;
if(num==0)num=9;
}
}
void display3(unsigned char *Data)//显示功能模块
{
unsigned char i,j,k;
for(k=0;k<9;k++)
{
DataPort=0x00; // 清空行锁存器里数据，防止出现乱码
line_LATCH=1; //
line_LATCH=0;
LATCH1=1;LATCH1=0;
LATCH2=1;LATCH2=0;
LATCH3=1;LATCH3=0;
LATCH4=1;LATCH4=0;
LATCH5=1;LATCH5=0;
LATCH6=1;LATCH6=0;
LATCH7=1;LATCH7=0;
LATCH8=1;LATCH8=0;
for(j=0;j<8;j++)
{
DataPort=0xff; // 清空行锁存器里数据，防止出现乱码
line_LATCH=1; //
line_LATCH=0;
for(i=0;i<8;i++)
{
DataPort=line[i]; //先给行（灯板的公共端）输入数据
line_LATCH=1; //打开锁存，把数据line[i]放进去
line_LATCH=0; //关闭锁存，阻止外部数据进来
DataPort=Data[i]; //把数值Data[0~7]里的值依次传给第一灯板的573锁存器中
LATCH8=1;LATCH8=0;
Delay(100); //扫描间隙延时，时间太长会闪烁，太短会造成重影
}
}
}
}
void display4(unsigned char *Data)//显示功能模块
{
unsigned char i,j,k;
for(k=0;k<9;k++)
{
DataPort=0x00; // 清空行锁存器里数据，防止出现乱码
line_LATCH=1; //
line_LATCH=0;
LATCH1=1;LATCH1=0;
LATCH2=1;LATCH2=0;
LATCH3=1;LATCH3=0;
LATCH4=1;LATCH4=0;
LATCH5=1;LATCH5=0;
LATCH6=1;LATCH6=0;
LATCH7=1;LATCH7=0;
LATCH8=1;LATCH8=0;
for(j=0;j<8;j++)
{
DataPort=0xff; // 清空行锁存器里数据，防止出现乱码
line_LATCH=1; //
line_LATCH=0;
for(i=0;i<8;i++)
{
DataPort=line[i]; //先给行（灯板的公共端）输入数据
line_LATCH=1; //打开锁存，把数据line[i]放进去
line_LATCH=0; //关闭锁存，阻止外部数据进来
DataPort=Data[i]; //把数值Data[0~7]里的值依次传给第一灯板的573锁存器中
LATCH1=1;LATCH1=0;
Delay(100); //扫描间隙延时，时间太长会闪烁，太短会造成重影
}
}
}
}
void zhuzi() //柱子移动效果
{
display1(Data0);
…………余下代码请下载附件…………

复制代码

ID:161756 · 发表于 2017-3-11 18:45

楼主，学习了

ID:170471 · 发表于 2017-3-23 23:28

怎么下载

ID:215796 · 发表于 2017-7-27 16:43

感谢楼主希望可以自己做出来

ID:233873 · 发表于 2017-9-18 18:59

谢谢楼主分享，正好想做一下

ID:243838 · 发表于 2017-10-29 09:43

厉害

ID:243899 · 发表于 2017-10-29 14:19

终于找到一个详细的制作过程了，谢谢楼主

ID:246357 · 发表于 2017-11-5 22:03

我下载看看

ID:240634 · 发表于 2017-11-8 16:00

早就想做个光立方了，这次有了详细教程，也动手做啦。

ID:248171 · 发表于 2017-11-11 10:28

楼主这个用的是怎样的电源？

ID:251670 · 发表于 2017-11-20 21:42

谢谢大佬

ID:252615 · 发表于 2017-11-23 12:14

很详细

ID:253360 · 发表于 2017-11-25 11:28

厉害了

ID:256662 · 发表于 2017-12-3 21:13

厉害啦

ID:262326 · 发表于 2017-12-16 13:10

厉害，厉害

ID:265800 · 发表于 2017-12-23 20:43

不知道用52能存多少程序

ID:239204 · 发表于 2017-12-29 13:41

做一个

ID:243662 · 发表于 2017-12-31 17:36

学习

ID:269710 · 发表于 2018-1-1 13:17

不错的资料，感谢楼主分享，不过个人制作，焊接太费事了，如果有现成的成品卖，特别是小型化的值得入手玩一玩。

ID:269861 · 发表于 2018-1-1 21:34

楼主，那个9脚排阻是多少欧的

ID:269861 · 发表于 2018-1-1 23:13

楼主，那个9脚排阻是多少欧的

ID:271679 · 发表于 2018-1-7 22:48

请教一下，清单当中的9脚排阻的参数是多少？

ID:242637 · 发表于 2018-1-13 16:12

下载看看哦，学习了

ID:275600 · 发表于 2018-1-13 16:14

学习了666666666666666666666666666666

ID:263517 · 发表于 2018-1-25 17:48

666 楼主厉害

ID:243748 · 发表于 2018-1-26 12:34

？学习了，谢谢分享

ID:197334 · 发表于 2018-1-30 17:08

感谢楼主

ID:280952 · 发表于 2018-1-30 17:30

谢谢楼主分享，我想问下这里循环变量为什么用的是无符号char型而不是int型

ID:280952 · 发表于 2018-1-30 18:06

很详细的资料，感谢

ID:282142 · 发表于 2018-2-4 16:49

谢谢大佬

ID:283996 · 发表于 2018-2-14 12:31

666 大佬

ID:284651 · 发表于 2018-2-23 18:35

感谢分享

ID:18004 · 发表于 2018-2-25 11:31

哇噻，好棒啊。谢谢分享！

ID:123874 · 发表于 2018-3-9 17:36

好东西，感谢分享

ID:259979 · 发表于 2018-3-10 05:49

感谢分享。。

ID:293274 · 发表于 2018-3-17 19:04

感谢分享

ID:278679 · 发表于 2018-3-18 10:30

谢谢了

ID:287807 · 发表于 2018-3-19 19:46

感谢分享

ID:284454 · 发表于 2018-3-19 22:10

有心共享资料了.
支持共享精神

ID:295187 · 发表于 2018-3-21 19:55

帅气，真的很棒

帐号		自动登录	找回密码
密码			立即注册

光立方的详细制作教程 含程序详解 原理图和仿真电路图等图片和资料下载

评分

光立方的详细制作教程含程序详解原理图和仿真电路图等图片和资料下载