80C51单片机通过模拟SPI口驱动UZZ9001读写操作

#include <reg51.h>   
#include<absacc.h>   
#include <intrins.h>   
#include<math.h>   
sbit CS  = P2^0;   
sbit CLK = P2^1;   
sbit DATA= P2^2;   
/*宏定义8155的A口，B口和控制口*/   
#define PA8155 XBYTE[0x7101]   
#define PB8155 XBYTE[0x7102]   
#define COM8155 XBYTE[0x7100]   

//显示[0,1,2,3,4,5,6,7,8,9,A,b,c,d,e,f]的代码；   
unsigned char code  Table[16]={0X0FC,0X60,0X0DA,0X0F2,0X66,0X0B6,0X0BE,0X0E0,0X0FE,0X0F6,0xee,0x3e,0x9c,0x7a,0xde,0x8e};   
unsigned char Buf[4]={0,0,0,0};             //对应四个数码管显示数据的缓冲区   


void delay(unsigned int time)  //延时                                           
{      
    while(time--);     
}   

/*************************************************  
函数名称：数码管显示  
功能：将四个缓冲区单元的内容分别显示到四个数码管上面  
参数：unsigned charp *Bufptr  
返回值：无  
**************************************************/   
void DISP_LED(unsigned char *Bufptr)   
{   
    unsigned char disi;   
    unsigned char BitCT=0X10;   
    for(disi=0;disi<4;disi++)   
    {   
        PA8155=BitCT;                                       //选中个位数码管   
        PB8155=Table[*Bufptr++]+(disi==1);                          //取段码   
        BitCT=_crol_(BitCT,1);                              //左移一位   
        delay(500);   
    }   
}   


unsigned int uzz9001(void)   
{   
    unsigned int i,temp=0;   
    CLK=1;   
    CS=1;   
    delay(5);   
    CS=0;   
    delay(1);   
    i=16;   
    while(i--)   
    {   
        temp<<=1;   
        CLK=0;   
        delay(5);   
        CLK=1;   
        if(DATA==1)   
            temp |=0x0001;   
        else   
            temp &=0xfffe;   
        delay(5);   
    }   
    CS=1;   
    return(temp);   
}   

float angle(void)   
{   
    unsigned int i,temp0,temp1,temp2=0;   
    float jiaodu;   
    for(i=0;i<8;i++)   
    {   
       temp0=uzz9001();   
       temp1=temp0&0x3f00;   
       temp1>>=1;   
       temp0&=0x007f;   
       temp0=temp0+temp1;   
       temp2+=temp0;   
    }   
    jiaodu=temp2*180.000/65536.000;   
    return(jiaodu);   
}   


void main()   
{   
  unsigned char count;   
  unsigned int jiaodu;   
  COM8155=0x03;   
  TMOD=0X01;   
  TH0=0X3c;       //初始化，定时50MS   
  TL0=0Xb0;   
  count=0;   
  TR0=1;   

  while(1)   
    {   
       DISP_LED(Buf);   
       if(TF0==1)    
       {   

          TF0=0;   
          count++;   
          if(count==10)   //20*50MS=1S   
          {   
              count=0;   
              jiaodu=(unsigned int) (angle()*10.0);   
               DISP_LED(Buf);   
              Buf[3]=jiaodu/1000;   
              Buf[2]=jiaodu%1000/100;      
              Buf[1]=jiaodu%100/10;   
              Buf[0]=jiaodu%10;   

          }   
       }   
    }   

}   

相关文章